Date: Tue, 21 Jan 2003 23:54:21 +0100 From: "Leif Neland" <leifn@neland.dk> To: <freebsd-scsi@FreeBSD.ORG> Subject: Re: Adaptec 19160 SCSI controller configuration error: 02 Message-ID: <061e01c2c1a0$0cde5260$6805a8c0@gina> References: <05b801c2c17a$a3cb0f40$6805a8c0@gina> <67532704.1043174381@aslan.btc.adaptec.com> <05c601c2c193$183d2990$6805a8c0@gina> <20030121144540.A3912@panzer.kdm.org> <061601c2c19e$a03e5bb0$6805a8c0@gina>
index | next in thread | previous in thread | raw e-mail
[-- Attachment #1 --]
> So what DOES "controller configuration error: 02" mean?
>
>
Question
When the Adaptec SCSI Select Utility loads, the following message
appears on the screen :
SCSI Controller Configuration Error 02
This applies to the following Product(s):
- Adaptec SCSI Card 39160, Adaptec SCSI Card 29160, Adaptec SCSI Card
29160LP, Adaptec SCSI Card 29160N, Adaptec SCSI Card 19160
This applies to the following Operating System(s):
- N/A
Answer
This error message will appear when connecting an HVD (High Voltage
Differential) SCSI device to the Low Voltage Differential (LVD) SCSI card.
Ultra 160 SCSI cards only support the use of Low Voltage Differential (LVD)
and Single-Ended (SE) devices.
CAUTION! Connecting HVD devices to a non-HVD SCSI controller may
damage both the device and the SCSI controller.
Determine if your device(s) being attached is a HVD device. Check for
any markings on the device, typically near the SCSI connector that may
indicate HVD or LVD/SE. However do not trust these marking completely,
double check the type of device inside the unit. Although the external case
may be marked as LVD, it is still possible the internal device may still be
an HVD device.
The manufacuter of the device(s) should be contacted, if reviewing the
documentation or visiting the manufacturers web shed light on the interface
style the device is using.
Note: When using a HVD (High Voltage Differential) device, a HVD SCSI
card must be used.
The correct Adaptec HVD SCSI product, would be an AHA-2944UW. This HVD
SCSI card, designed specifically to work with HVD SCSI devices only.
Question
When the Adaptec SCSI Select Utility loads, the following message
appears on the screen :
SCSI Controller Configuration Error 02
This applies to the following Product(s):
- Adaptec SCSI Card 39160, Adaptec SCSI Card 29160, Adaptec SCSI Card
29160LP, Adaptec SCSI Card 29160N, Adaptec SCSI Card 19160
This applies to the following Operating System(s):
- N/A
Answer
This error message will appear when connecting an HVD (High Voltage
Differential) SCSI device to the Low Voltage Differential (LVD) SCSI card.
Ultra 160 SCSI cards only support the use of Low Voltage Differential (LVD)
and Single-Ended (SE) devices.
CAUTION! Connecting HVD devices to a non-HVD SCSI controller may
damage both the device and the SCSI controller.
Determine if your device(s) being attached is a HVD device. Check for
any markings on the device, typically near the SCSI connector that may
indicate HVD or LVD/SE. However do not trust these marking completely,
double check the type of device inside the unit. Although the external case
may be marked as LVD, it is still possible the internal device may still be
an HVD device.
The manufacuter of the device(s) should be contacted, if reviewing the
documentation or visiting the manufacturers web shed light on the interface
style the device is using.
Note: When using a HVD (High Voltage Differential) device, a HVD SCSI
card must be used.
The correct Adaptec HVD SCSI product, would be an AHA-2944UW. This HVD
SCSI card, designed specifically to work with HVD SCSI devices only.
But does that make sense that I get that error even with cable, but without
disk? Can a _cable_ be a HVD device? It does have a terminator at the end.
Leif
[-- Attachment #2 --]
GIF89a ‘ÿ ÿÿÿ ÿÿÿ !ÿ ADOBE:IR1.0Þí !ù , T ;
home |
help
Want to link to this message? Use this
URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?061e01c2c1a0$0cde5260$6805a8c0>