Date: Fri, 1 Apr 2022 16:13:23 +0300 From: Oleksandr Kryvulia <shuriku@shurik.kiev.ua> To: "Bjoern A. Zeeb" <bz@FreeBSD.org> Cc: FreeBSD wireless mailing list <wireless@freebsd.org> Subject: Re: iwlwifi failed to attach Message-ID: <a49d45fd-6039-2ab8-7ac2-164ed38bf9f2@shurik.kiev.ua> In-Reply-To: <alpine.BSF.2.00.2204011137300.68830@ai.fobar.qr> References: <85f3cdd5-9bcc-426b-55e8-f3964de87c52@shurik.kiev.ua> <alpine.BSF.2.00.2203291300170.68830@ai.fobar.qr> <87e39641-f6c2-3306-e89d-fe6ba5a8ff39@shurik.kiev.ua> <alpine.BSF.2.00.2203291324050.68830@ai.fobar.qr> <89fa7191-30aa-e550-0e5d-d061c985c5ab@shurik.kiev.ua> <alpine.BSF.2.00.2204010044480.68830@ai.fobar.qr> <2c64cf74-ec67-5e6d-e36d-df1bb2c5a402@shurik.kiev.ua> <alpine.BSF.2.00.2204011137300.68830@ai.fobar.qr>
index | next in thread | previous in thread | raw e-mail
01.04.22 14:53, Bjoern A. Zeeb пишет: > On Fri, 1 Apr 2022, Oleksandr Kryvulia wrote: > >> 01.04.22 03:59, Bjoern A. Zeeb пишет: >>> Sorry, I think I have to roll this back. >>> >>> I assume you are on GENERIC? >> Yes, GENERIC-NODEBUG. >>> >>> I assume iwm(4) normally is loaded as a module along with firmware >>> and works fine? >> Yes, iwm(4) works fine, I'm sending this message over it. >>> >>> Ignoring the above hint.iwm... if you move if_iwm.ko out of >>> /boot/kernel temporary and run kldxref /boot/kernel and reboot >>> on a recent main or stable/13, what happens without you doing any >>> devctl? Is iwlfiwi auto-loaded? does pciconf show the BAR enabled >>> then? >> >> # mv /boot/kernel/if_iwm.ko /home/o.kryvulia/ >> # kldxref /boot/kernel >> # shutdown -p now >> >> Power on and boot: >> >> Autoloading module: if_iwlwifi >> Intel(R) Wireless WiFi based driver for FreeBSD >> Autoloading module: ig4 >> Autoloading module: pchtherm >> pchtherm0: <CannonLake-LP Thermal Subsystem> mem >> 0xdd643000-0xdd643fff at device 18.0 on pci0 >> iwlwifi0: <iwlwifi> mem 0xdd638000-0xdd63bfff at device 20.3 on pci0 >> iwlwifi0: HW_REV=0xFFFFFFFF, PCI issues? >> device_attach: iwlwifi0 attach returned 5 >> >> pciconf shows the same: >> >> none3@pci0:0:20:3: class=0x028000 rev=0x30 hdr=0x00 >> vendor=0x8086 device=0x9df0 subvendor=0x8086 subdevice=0x0034 >> vendor = 'Intel Corporation' >> device = 'Cannon Point-LP CNVi [Wireless-AC]' >> class = network >> bar [10] = type Memory, range 64, base 0xdd638000, size 16384, >> disabled >> cap 01[c8] = powerspec 3 supports D0 D3 current D3 >> cap 05[d0] = MSI supports 1 message, 64 bit >> cap 10[40] = PCI-Express 2 root endpoint max data 128(128) FLR RO NS >> max read 128 >> cap 11[80] = MSI-X supports 16 messages >> Table in map 0x10[0x2000], PBA in map 0x10[0x3000] >> ecap 0000[100] = unknown 0 >> ecap 0018[14c] = LTR 1 >> ecap 000b[164] = Vendor [1] ID 0010 Rev 0 Length 20 > > Okay, can I ask you for one last test. Can you boot -s (to single > user) and check the full pciconf there and then simply exit and let > to boot continue back to iwm. You may need to mount -uw / in order to > save the full pciconf output. > > iwlwifi tends to disable resources on detach, so we could se an > aftermath problem here even on attach failure. I just want to make > sure given the device is in D3 that we do boot up and are good before > any wifi driver attaches. > > Later, > Bjoern > I'v got it solved for now. The reason was inhw.pci.do_power_nodriver=3 which was setted in both /boot/loader.conf and /etc/sysctl.conf. iwlwifi0@pci0:0:20:3: class=0x028000 rev=0x30 hdr=0x00 vendor=0x8086 device=0x9df0 subvendor=0x8086 subdevice=0x0034 vendor = 'Intel Corporation' device = 'Cannon Point-LP CNVi [Wireless-AC]' class = network bar [10] = type Memory, range 64, base 0xdd638000, size 16384, enabled cap 01[c8] = powerspec 3 supports D0 D3 current D0 cap 05[d0] = MSI supports 1 message, 64 bit cap 10[40] = PCI-Express 2 root endpoint max data 128(128) FLR RO NS max read 128 cap 11[80] = MSI-X supports 16 messages, enabled Table in map 0x10[0x2000], PBA in map 0x10[0x3000] ecap 0000[100] = unknown 0 ecap 0018[14c] = LTR 1 ecap 000b[164] = Vendor [1] ID 0010 Rev 0 Length 20 Thank you for your help and sorry for wasted time.home | help
Want to link to this message? Use this
URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?a49d45fd-6039-2ab8-7ac2-164ed38bf9f2>