Date: Fri, 11 Apr 1997 06:50:42 -0400 (EDT) From: Murali Rangarajan <muralir@rci.rutgers.edu> To: isp@freebsd.org Subject: trouble with xfree Message-ID: <Pine.GSO.3.94.970411064557.27665A-100000@niflheim.rutgers.edu>
next in thread | raw e-mail | index | archive | help
Hi, I installed freebsd 2.2.1 yesterday, and when i tried to run X, i got the following error(i am including the transcript of the entrire session) Can somebody tell me what the problem is? I have a 2 button mouse and i configured it to be a bus mouse... ----------- XFree86 Version 3.2 / X Window System (protocol Version 11, revision 0, vendor release 6100) Release Date: Oct 26 1996 If the server is older than 6-12 months, or if your card is newer than the above date, look for a newer version before reporting problems. (see http://www.XFree86.Org/FAQ) Operating System: FreeBSD 2.2.0 Configured drivers: S3: accelerated server for S3 graphics adaptors (Patchlevel 0) newmmio, mmio_928, s3_generic Using syscons driver with X support (version 2.0) (using VT number 4) XF86Config: /etc/XF86Config (**) stands for supplied, (--) stands for probed/default values (**) XKB: disabled (**) XKB: keymap: "xfree86(us)" (overrides other XKB settings) (**) Mouse: type: Microsoft, device: /dev/mouse, baudrate: 1200, 3 button emulation (timeout: 50ms) (**) S3: Graphics device ID: "Trio 64+" (**) S3: Monitor ID: "svga" (--) S3: Mode "800x600" needs hsync freq of 35.16 kHz. Deleted. (--) S3: Mode "1024x768" needs hsync freq of 35.52 kHz. Deleted. (--) S3: Mode "640x480" needs hsync freq of 36.46 kHz. Deleted. (--) S3: Mode "800x600" needs hsync freq of 37.88 kHz. Deleted. (--) S3: Mode "800x600" needs hsync freq of 48.08 kHz. Deleted. (--) S3: Mode "1024x768" needs hsync freq of 48.36 kHz. Deleted. (--) S3: Mode "1024x768" needs hsync freq of 56.48 kHz. Deleted. (--) S3: Mode "1280x1024" needs hsync freq of 51.02 kHz. Deleted. (--) S3: Mode "1024x768" needs hsync freq of 62.50 kHz. Deleted. (--) S3: Mode "1280x1024" needs hsync freq of 64.25 kHz. Deleted. (--) S3: Mode "1280x1024" needs hsync freq of 78.86 kHz. Deleted. (--) S3: Mode "1280x1024" needs hsync freq of 81.13 kHz. Deleted. (--) S3: Mode "320x240" needs hsync freq of 39.38 kHz. Deleted. (--) S3: Mode "400x300" needs hsync freq of 35.16 kHz. Deleted. (--) S3: Mode "400x300" needs hsync freq of 37.88 kHz. Deleted. (--) S3: Mode "400x300" needs hsync freq of 48.08 kHz. Deleted. (--) S3: Mode "480x300" needs hsync freq of 35.16 kHz. Deleted. (--) S3: Mode "480x300" needs hsync freq of 37.80 kHz. Deleted. (--) S3: Mode "480x300" needs hsync freq of 39.56 kHz. Deleted. (--) S3: Mode "480x300" needs hsync freq of 48.00 kHz. Deleted. (**) FontPath set to "/usr/X11R6/lib/X11/fonts/misc/,/usr/X11R6/lib/X11/fonts/75dpi/:unscaled,/usr/X11R6/lib/X11/fonts/75dpi/" (--) S3: PCI: Trio32/64 rev 0, Linear FB @ 0xf8000000 (--) S3: card type: PCI (--) S3: chipset: Trio64 rev. 201 (--) S3: chipset driver: mmio_928 (--) S3: videoram: 1024k (--) S3: Ramdac type: s3_trio64 (--) S3: Ramdac speed: 135 (--) S3: Using Trio32/64 programmable clock (MCLK 59.957 MHz) (--) S3: Maximum allowed dot-clock: 135.000 MHz (**) S3: Mode "640x480": mode clock = 25.175 (--) S3: There is no mode definition named "800x600" (--) S3: Removing mode "800x600" from list of valid modes. (--) S3: There is no mode definition named "1024x768" (--) S3: Removing mode "1024x768" from list of valid modes. (--) S3: Using 6 bits per RGB value (--) S3: Virtual resolution set to 640x480 (--) S3: Local bus LAW is 0xF8000000 (--) S3: Using a banksize of 1024k, line width of 640 (--) S3: Using a single 64x64 area at (576,482) for expanding pixmaps (--) S3: Using 8 planes of 640x1092 at (0,546) aligned 8 as font cache MIT-SHM extension disabled due to lack of kernel support PEX extension module not loaded XIE extension module not loaded Fatal server error: Cannot open mouse (Device not configured) ------------------- Thanks Murali
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.GSO.3.94.970411064557.27665A-100000>