Date: Tue, 18 Mar 2008 10:14:34 -0700 From: David Wolfskill <david@catwhisker.org> To: freebsd-hardware@freebsd.org Subject: Dell Optiplex 755 hangs every other boot before 82801 Family Hub Interface to PCI Bridge probed Message-ID: <20080318171434.GA49159@bunrab.catwhisker.org>
next in thread | raw e-mail | index | archive | help
--Y7xTucakfITjPcLV
Content-Type: multipart/mixed; boundary="ibTvN161/egqYuK8"
Content-Disposition: inline
--ibTvN161/egqYuK8
Content-Type: text/plain; charset=us-ascii
Content-Disposition: inline
Content-Transfer-Encoding: quoted-printable
This may prove to be an ACPI issue, but I didn't want to start the
thread with a cross-post: it might set a bad example. :-}
So at work, I was assigned a shiny new Dell Optiplex 755; when I
arrived, it had some flavor of Linux installed on it; I overlaid that
with my usual FreeBSD workstation/laptop install, where I have 4
bootable slices:
* Slice 1 -- RELENG_6
* Slice 2 -- used for experimenting
* Slice 3 -- RELENG_7
* Slice 4 -- HEAD
During the course of setting this up, I had occasion to reboot the
machine a few times. And I noticed a peculiar pattern: once it had been
up & running, the next boot would hang just after
=2E..
ehci1: [GIANT-LOCKED]
usb6: EHCI version 1.0
usb6: companion controllers, 2 ports each: usb3 usb4 usb5
usb6: <EHCI (generic) USB 2.0 controller> on ehci1
usb6: USB revision 2.0
uhub6: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub6: 6 ports with 6 removable, self powered
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
=3D=3D=3D> hang <=3D=3D=3D
The only thing I've found that gets it out of that hang is a forced
power-cycle. Once that's done, the next boot proceeds normally, as if
there were nothing wrong; such a successful (RELENG_6) boot then
continues with:
pci2: <ACPI PCI bus> on pcib2
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
=2E...
If I try power-cycling during an ill-fated boot sequence, but before it
gets to the "hang" point, it will hang on the next boot anyway -- it's
as if the silly machine has a desperate need to hang on a boot before it
will behave ... "rationally" (to the extent the concept makes sense --
and at significant risk of over-anthropomorphizing).
pciconf(8) identifies the last device probed before the hang as:
pcib2@pci0:30:0: class=3D0x060401 card=3D0x02111028 chip=3D0x244e808=
6 rev=3D0x92 hdr=3D0x01
vendor =3D 'Intel Corporation'
device =3D '82801 Family (ICH2/3/4/4/5/5/6/7/8/9,63xxESB) Hub Inter=
face to PCI Bridge'
class =3D bridge
subclass =3D PCI-PCI
I've attached a complete dmesg.boot from a successful RELENG_6 boot,
as well as the output form pciconf -lv.
The "hang pattern" appears to be invariant regardless whether I
boot RELENG_6, RELENG_7, or HEAD.
Please include me on responses, as I am not currently subscribed
to hardware@. (For mail clients that honor it, I've set Reply-To.)
Peace,
david
--=20
David H. Wolfskill david@catwhisker.org
I submit that "conspiracy" would be an appropriate collective noun for cats.
See http://www.catwhisker.org/~david/publickey.gpg for my public key.
--ibTvN161/egqYuK8
Content-Type: text/plain; charset=us-ascii
Content-Disposition: attachment; filename="dmesg.boot"
Copyright (c) 1992-2008 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.3-STABLE #2: Tue Feb 26 10:17:07 PST 2008
root@dwolf-bsd.jnpr.net:/common/S1/obj/usr/src/sys/DWOLF
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Core(TM)2 Duo CPU E4400 @ 2.00GHz (1995.00-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x6fd Stepping = 13
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0xe39d<SSE3,RSVD2,MON,DS_CPL,EST,TM2,SSSE3,CX16,xTPR,PDCM>
AMD Features=0x20000000<LM>
AMD Features2=0x1<LAHF>
Cores per package: 2
real memory = 2102390784 (2004 MB)
avail memory = 2047827968 (1952 MB)
ACPI APIC Table: <DELL B9K >
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
ioapic0: Changing APIC ID to 8
ioapic0 <Version 2.0> irqs 0-23 on motherboard
lapic0: Forcing LINT1 to edge trigger
kbd1 at kbdmux0
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
hptrr: HPT RocketRAID controller driver v1.1 (Feb 26 2008 10:16:06)
acpi0: <DELL B9K > on motherboard
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 900
cpu0: <ACPI CPU> on acpi0
acpi_perf0: <ACPI CPU Frequency Control> on cpu0
cpu1: <ACPI CPU> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: <display, VGA> at device 2.0 (no driver attached)
pci0: <display> at device 2.1 (no driver attached)
pci0: <simple comms> at device 3.0 (no driver attached)
atapci0: <Intel ATA controller> port 0xfe80-0xfe87,0xfe90-0xfe93,0xfea0-0xfea7,0xfeb0-0xfeb3,0xfef0-0xfeff irq 18 at device 3.2 on pci0
ata2: <ATA channel 0> on atapci0
ata3: <ATA channel 1> on atapci0
pci0: <simple comms, UART> at device 3.3 (no driver attached)
em0: <Intel(R) PRO/1000 Network Connection Version - 6.7.3> port 0xecc0-0xecdf mem 0xfe9e0000-0xfe9fffff,0xfe9db000-0xfe9dbfff irq 21 at device 25.0 on pci0
em0: Using MSI interrupt
em0: Ethernet address: 00:1a:a0:62:96:09
uhci0: <UHCI (generic) USB controller> port 0xff20-0xff3f irq 16 at device 26.0 on pci0
uhci0: [GIANT-LOCKED]
usb0: <UHCI (generic) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <UHCI (generic) USB controller> port 0xff00-0xff1f irq 17 at device 26.1 on pci0
uhci1: [GIANT-LOCKED]
usb1: <UHCI (generic) USB controller> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfe9d9c00-0xfe9d9fff irq 22 at device 26.7 on pci0
ehci0: [GIANT-LOCKED]
usb2: EHCI version 1.0
usb2: wrong number of companions (3 != 2)
usb2: companion controllers, 2 ports each: usb0 usb1
usb2: <EHCI (generic) USB 2.0 controller> on ehci0
usb2: USB revision 2.0
uhub2: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 6 ports with 6 removable, self powered
pcm0: <Intel 82801I High Definition Audio Controller> mem 0xfe9dc000-0xfe9dffff irq 16 at device 27.0 on pci0
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pci1: <ACPI PCI bus> on pcib1
uhci2: <UHCI (generic) USB controller> port 0xff80-0xff9f irq 23 at device 29.0 on pci0
uhci2: [GIANT-LOCKED]
usb3: <UHCI (generic) USB controller> on uhci2
usb3: USB revision 1.0
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
uhci3: <UHCI (generic) USB controller> port 0xff60-0xff7f irq 17 at device 29.1 on pci0
uhci3: [GIANT-LOCKED]
usb4: <UHCI (generic) USB controller> on uhci3
usb4: USB revision 1.0
uhub4: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub4: 2 ports with 2 removable, self powered
uhci4: <UHCI (generic) USB controller> port 0xff40-0xff5f irq 18 at device 29.2 on pci0
uhci4: [GIANT-LOCKED]
usb5: <UHCI (generic) USB controller> on uhci4
usb5: USB revision 1.0
uhub5: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub5: 2 ports with 2 removable, self powered
ehci1: <EHCI (generic) USB 2.0 controller> mem 0xff980800-0xff980bff irq 23 at device 29.7 on pci0
ehci1: [GIANT-LOCKED]
usb6: EHCI version 1.0
usb6: companion controllers, 2 ports each: usb3 usb4 usb5
usb6: <EHCI (generic) USB 2.0 controller> on ehci1
usb6: USB revision 2.0
uhub6: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub6: 6 ports with 6 removable, self powered
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci2: <ACPI PCI bus> on pcib2
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci1: <Intel AHCI controller> port 0xfe00-0xfe07,0xfe10-0xfe13,0xfe20-0xfe27,0xfe30-0xfe33,0xfec0-0xfedf mem 0xff970000-0xff9707ff irq 18 at device 31.2 on pci0
atapci1: AHCI Version 01.20 controller with 6 ports detected
ata4: <ATA channel 0> on atapci1
ata5: <ATA channel 1> on atapci1
ata6: <ATA channel 2> on atapci1
ata7: <ATA channel 3> on atapci1
ata8: <ATA channel 4> on atapci1
ata8: port not implemented
ata9: <ATA channel 5> on atapci1
ichsmb0: <SMBus controller> port 0xece0-0xecff mem 0xfe9d9b00-0xfe9d9bff irq 18 at device 31.3 on pci0
ichsmb0: [GIANT-LOCKED]
smbus0: <System Management Bus> on ichsmb0
smb0: <SMBus generic I/O> on smbus0
fdc0: <floppy drive controller (FDE)> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0: <ECP parallel printer port> port 0x378-0x37f,0x778-0x77f irq 7 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xcb7ff,0xcb800-0xcd7ff,0xcd800-0xcffff on isa0
ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
ata1 at port 0x170-0x177,0x376 irq 15 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ums0: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM), rev 1.10/3.00, addr 2, iclass 3/1
ums0: 3 buttons and Z dir.
ukbd0: Key Tronic Keytronic USB Keyboard, rev 1.10/1.02, addr 3, iclass 3/1
kbd2 at ukbd0
Timecounters tick every 1.000 msec
hptrr: no controller detected.
ad8: 76293MB <Seagate ST380815AS 3.ADA> at ata4-master SATA300
acd0: CDRW <HL-DT-STCD-RW/DVD-ROM GCC-T10N/A100> at ata5-master UDMA33
pcm0: <HDA Codec: Analog Devices AD1984>
pcm0: <HDA Driver Revision: 20071129_0050>
lapic1: Forcing LINT1 to edge trigger
SMP: AP CPU #1 Launched!
Trying to mount root from ufs:/dev/ad8s1a
--ibTvN161/egqYuK8
Content-Type: text/plain; charset=us-ascii
Content-Disposition: attachment; filename=pciconf
hostb0@pci0:0:0: class=0x060000 card=0x02111028 chip=0x29b08086 rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '(??) DRAM Controller'
class = bridge
subclass = HOST-PCI
none0@pci0:2:0: class=0x030000 card=0x02111028 chip=0x29b28086 rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '(??) Integrated Graphics Controller'
class = display
subclass = VGA
none1@pci0:2:1: class=0x038000 card=0x02111028 chip=0x29b38086 rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '(??) Integrated Graphics Controller'
class = display
none2@pci0:3:0: class=0x078000 card=0x02111028 chip=0x29b48086 rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '(??) HECI Controller'
class = simple comms
atapci0@pci0:3:2: class=0x010185 card=0x02111028 chip=0x29b68086 rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '(??) PT IDER Controller'
class = mass storage
subclass = ATA
none3@pci0:3:3: class=0x070002 card=0x02111028 chip=0x29b78086 rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '(??) Serial KT Controller'
class = simple comms
subclass = UART
em0@pci0:25:0: class=0x020000 card=0x02111028 chip=0x10bd8086 rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82566DM-2 Gigabit Network Connection'
class = network
subclass = ethernet
uhci0@pci0:26:0: class=0x0c0300 card=0x02111028 chip=0x29378086 rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801IB/IR/IH (ICH9 Family) USB Universal Host Controller'
class = serial bus
subclass = USB
uhci1@pci0:26:1: class=0x0c0300 card=0x02111028 chip=0x29388086 rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801IB/IR/IH (ICH9 Family) USB Universal Host Controller'
class = serial bus
subclass = USB
ehci0@pci0:26:7: class=0x0c0320 card=0x02111028 chip=0x293c8086 rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801IB/IR/IH (ICH9 Family) USB2 Enhanced Host Controller'
class = serial bus
subclass = USB
pcm0@pci0:27:0: class=0x040300 card=0x02111028 chip=0x293e8086 rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801IB/IR/IH (ICH9 Family) HD Audio Controller'
class = multimedia
pcib1@pci0:28:0: class=0x060400 card=0x02111028 chip=0x29408086 rev=0x02 hdr=0x01
vendor = 'Intel Corporation'
device = '82801IB/IR/IH (ICH9 Family) PCIe Root Port 1'
class = bridge
subclass = PCI-PCI
uhci2@pci0:29:0: class=0x0c0300 card=0x02111028 chip=0x29348086 rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801IB/IR/IH (ICH9 Family) USB Universal Host Controller'
class = serial bus
subclass = USB
uhci3@pci0:29:1: class=0x0c0300 card=0x02111028 chip=0x29358086 rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801IB/IR/IH (ICH9 Family) USB Universal Host Controller'
class = serial bus
subclass = USB
uhci4@pci0:29:2: class=0x0c0300 card=0x02111028 chip=0x29368086 rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801IB/IR/IH (ICH9 Family) USB Universal Host Controller'
class = serial bus
subclass = USB
ehci1@pci0:29:7: class=0x0c0320 card=0x02111028 chip=0x293a8086 rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801IB/IR/IH (ICH9 Family) USB2 Enhanced Host Controller'
class = serial bus
subclass = USB
pcib2@pci0:30:0: class=0x060401 card=0x02111028 chip=0x244e8086 rev=0x92 hdr=0x01
vendor = 'Intel Corporation'
device = '82801 Family (ICH2/3/4/4/5/5/6/7/8/9,63xxESB) Hub Interface to PCI Bridge'
class = bridge
subclass = PCI-PCI
isab0@pci0:31:0: class=0x060100 card=0x00000000 chip=0x29148086 rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801IB/IR/IH (ICH9 Family) DO LPC Interface Controller'
class = bridge
subclass = PCI-ISA
atapci1@pci0:31:2: class=0x010601 card=0x02111028 chip=0x29228086 rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801IB/IR/IH (ICH9 Family) 6 port SATA AHCI Controller'
class = mass storage
ichsmb0@pci0:31:3: class=0x0c0500 card=0x02111028 chip=0x29308086 rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801IB/IR/IH (ICH9 Family) SMBus Controller'
class = serial bus
subclass = SMBus
--ibTvN161/egqYuK8--
--Y7xTucakfITjPcLV
Content-Type: application/pgp-signature
Content-Disposition: inline
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.0 (FreeBSD)
iEYEARECAAYFAkff+HkACgkQmprOCmdXAD0hTwCePcPxG89dsWYMs0Rm9TPnY6Xh
mFUAniRC9O9Z7WKg5pJmXD0ut7IxIpGe
=s5Fq
-----END PGP SIGNATURE-----
--Y7xTucakfITjPcLV--
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20080318171434.GA49159>