Date: Mon, 24 Nov 2008 23:36:20 +0300 From: Anton Yuzhaninov <citrin@citrin.ru> To: current@freebsd.org Subject: Re: problem with Marvell ATA on current Message-ID: <492B1044.8030705@citrin.ru> In-Reply-To: <4929EAC5.6070308@delphij.net> References: <4929C63D.6020808@citrin.ru> <4929EAC5.6070308@delphij.net>
next in thread | previous in thread | raw e-mail | index | archive | help
On 24.11.2008 02:44, Xin LI wrote: > Anton Yuzhaninov wrote: >> Marvell ATA controller on current (from Nov 20, amd64) don't work under >> load >> (e. g. when make buildworld started). >> >> With RELENG_7 same hardware works fine. > > Could you please confirm that it's a fresh RELENG_7 (ideally it's > sync'ed within this month)? box was reinstalled and upgraded to fresh RELENG_7: 7.1-PRERELEASE FreeBSD 7.1-PRERELEASE #0: Mon Nov 24 21:18:12 MSK 2008 ATA works without problems. > >> From pciconf: >> >> atapci4@pci0:3:6:0: class=0x010000 card=0x81501043 chip=0x604111ab >> rev=0x09 hdr=0x00 >> vendor = 'Marvell Semiconductor (Was: Galileo Technology Ltd)' >> device = 'MV88SX6041 Marvell Technology Group Ltd. MV88SX6041 >> 4-port SATA II PCI-X Controller (rev 03)' >> class = mass storage >> subclass = SCSI >> cap 01[40] = powerspec 2 supports D0 D3 current D0 >> cap 05[50] = MSI supports 1 message, 64 bit >> cap 07[60] = PCI-X 64-bit supports 133MHz, 512 burst read, 4 split >> transactions >> >> From dmesg: >> >> ad16: FAILURE - load data >> ad16: setting up DMA failed >> ad20: FAILURE - load data >> ad20: setting up DMA failed >> GEOM_MIRROR: ad18: FAILURE - load data >> ad18: setting up DMA failed >> Request failed (error=5).ad18: FAILURE - load data >> ad18: setting up DMA failed >> ad16s1[WRITE(offset=7948492800, length=131072)] >> GEOM_MIRRORad16: FAILURE - load data >> ad16: : setting up DMA failedRequest failed (error=5). >> ad20: FAILURE - load data >> ad20: ad20s1[WRITE(offset=7948492800, length=131072)]setting up DMA failed >> ad16: FAILURE - load data >> ad16: setting up DMA failed >> ad16: >> GEOM_MIRRORFAILURE - load data: >> ad16: Request failed (error=5).setting up DMA failed >> ad16: FAILURE - load data >> ad16: setting up DMA faileda >> d18s1[WRITE(offset=7948722176, length=131072)]ad16: FAILURE - load data >> ad16: setting up DMA failed >> ad20: FAILURE - load data >> .... >> ad16: FAILURE - load data >> ad16: setting up DMA failed >> ad16: FAILURE - load data >> ad16: setting up DMA failed >> GEOM_MIRROR: Device gm0s1: provider ad16s1 disconnected. >> GEOM_MIRROR: Component ad16cs1 (device gm0s1) broken, skipping. >> GEOM_MIRROR: Cannot add disk ad16cs1 to gm0s1 (error=22).
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?492B1044.8030705>