Date: Thu, 16 Mar 2006 07:23:40 -0500 From: "Matt" <matt@successfulhosting.com> To: "'Jack Vogel'" <jfvogel@gmail.com>, <freebsd-net@freebsd.org> Subject: RE: IPMI During Boot Message-ID: <007b01c648f4$75eb41d0$75a31f9b@BLADESNITZ> In-Reply-To: <2a41acea0603151100s45dae1b0mcd9281ff2fe32402@mail.gmail.com>
next in thread | previous in thread | raw e-mail | index | archive | help
Hello,
The help is much appreciate. Just to test thoroughly, I recompiled my
kernel without the em driver, and I didn't load the module in loader.conf.
Upon rebooting, it flew through just fine, and I was even able to drop to
single-user mode with no issues. I then enabled the em module in the
loader.conf, and got the results as before, I'm dead in the water until the
network is configured.
Below is the information you requested.
The IPMI Card is currently configured as:
IP: 192.168.2.110
MAC: 00:30:48:2F:A0:80
Here's the ifconfig:
em0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
options=b<RXCSUM,TXCSUM,VLAN_MTU>
inet 192.168.2.105 netmask 0xffffff00 broadcast 192.168.2.255
ether 00:30:48:2f:a0:80
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
And pciconf -v -l output:
hostb0@pci0:0:0: class=0x060000 card=0x688015d9 chip=0x35908086
rev=0x0c hdr=0x00
vendor = 'Intel Corporation'
device = 'E752x Server Memory Controller Hub'
class = bridge
subclass = HOST-PCI
none0@pci0:0:1: class=0xff0000 card=0x688015d9 chip=0x35918086 rev=0x0c
hdr=0x00
vendor = 'Intel Corporation'
device = 'E752x Memory Controller Hub Error Reporting Registers'
none1@pci0:1:0: class=0x088000 card=0x688015d9 chip=0x35948086 rev=0x0c
hdr=0x00
vendor = 'Intel Corporation'
device = 'E752x Memory Controller Hub DMA Controller'
class = base peripheral
pcib1@pci0:2:0: class=0x060400 card=0x00000050 chip=0x35958086 rev=0x0c
hdr=0x01
vendor = 'Intel Corporation'
device = 'E752x Memory Controller Hub PCI Express Port A0'
class = bridge
subclass = PCI-PCI
pcib4@pci0:4:0: class=0x060400 card=0x00000050 chip=0x35978086 rev=0x0c
hdr=0x01
vendor = 'Intel Corporation'
device = 'E752x Memory Controller Hub PCI Express Port B0'
class = bridge
subclass = PCI-PCI
pcib5@pci0:6:0: class=0x060400 card=0x00000050 chip=0x35998086 rev=0x0c
hdr=0x01
vendor = 'Intel Corporation'
device = 'E752x Memory Controller Hub PCI Express Port C0'
class = bridge
subclass = PCI-PCI
pcib6@pci0:30:0: class=0x060400 card=0x00000000 chip=0x244e8086
rev=0xc2 hdr=0x01
vendor = 'Intel Corporation'
device = '82801BA/CA/DB/DBL/EB/ER/FB (ICH2/3/4/4/5/5/6), 6300ESB Hub
Interface to PCI Bridge'
class = bridge
subclass = PCI-PCI
isab0@pci0:31:0: class=0x060100 card=0x00000000 chip=0x24d08086
rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801EB/ER (ICH5/ICH5R) LPC Interface Bridge'
class = bridge
subclass = PCI-ISA
atapci0@pci0:31:1: class=0x01018a card=0x688015d9 chip=0x24db8086
rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801EB/ER (ICH5/ICH5R) EIDE Controller'
class = mass storage
subclass = ATA
none2@pci0:31:3: class=0x0c0500 card=0x688015d9 chip=0x24d38086
rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82801EB/ER (ICH5/ICH5R) SMBus Controller'
class = serial bus
subclass = SMBus
pcib2@pci1:0:0: class=0x060400 card=0x00000044 chip=0x03298086 rev=0x09
hdr=0x01
vendor = 'Intel Corporation'
device = '6700PXH PCI Express-to-PCI Express Bridge A'
class = bridge
subclass = PCI-PCI
none3@pci1:0:1: class=0x080020 card=0x688015d9 chip=0x03268086 rev=0x09
hdr=0x00
vendor = 'Intel Corporation'
device = 'PCI Bridge Hub I/OxAPIC Interrupt Controller A'
class = base peripheral
subclass = interrupt controller
pcib3@pci1:0:2: class=0x060400 card=0x00000044 chip=0x032a8086 rev=0x09
hdr=0x01
vendor = 'Intel Corporation'
device = '6700PXH PCI Express-to-PCI Express Bridge B'
class = bridge
subclass = PCI-PCI
none4@pci1:0:3: class=0x080020 card=0x688015d9 chip=0x03278086 rev=0x09
hdr=0x00
vendor = 'Intel Corporation'
device = 'PCI Bridge Hub I/OxAPIC Interrupt Controller B'
class = base peripheral
subclass = interrupt controller
em0@pci2:3:0: class=0x020000 card=0x117a15d9 chip=0x10798086 rev=0x03
hdr=0x00
vendor = 'Intel Corporation'
device = '82546EB Dual Port Gigabit Ethernet Controller'
class = network
subclass = ethernet
em1@pci2:3:1: class=0x020000 card=0x117a15d9 chip=0x10798086 rev=0x03
hdr=0x00
vendor = 'Intel Corporation'
device = '82546EB Dual Port Gigabit Ethernet Controller'
class = network
subclass = ethernet
ahd0@pci3:4:0: class=0x010000 card=0x688015d9 chip=0x801d9005 rev=0x10
hdr=0x00
vendor = 'Adaptec Inc'
device = 'AIC-7902B Ultra320 SCSI Controller'
class = mass storage
subclass = SCSI
ahd1@pci3:4:1: class=0x010000 card=0x688015d9 chip=0x801d9005 rev=0x10
hdr=0x00
vendor = 'Adaptec Inc'
device = 'AIC-7902B Ultra320 SCSI Controller'
class = mass storage
subclass = SCSI
none5@pci6:1:0: class=0x030000 card=0x80081002 chip=0x47521002 rev=0x27
hdr=0x00
vendor = 'ATI Technologies Inc'
device = 'Rage XL PCI'
class = display
subclass = VGA
Matt Houston
Systems Administrator
Successful Hosting
matt@successfulhosting.com
http://www.SuccessfulHosting.com
Toll-Free: +1.866.494.5096
=================================
The Success behind your web site!
=================================
-----Original Message-----
From: owner-freebsd-net@freebsd.org [mailto:owner-freebsd-net@freebsd.org]
On Behalf Of Jack Vogel
Sent: Wednesday, March 15, 2006 2:01 PM
To: Julian Elischer
Cc: Matt; freebsd-net@freebsd.org
Subject: Re: IPMI During Boot
On 3/15/06, Jack Vogel <jfvogel@gmail.com> wrote:
> On 3/15/06, Julian Elischer <julian@elischer.org> wrote:
> >
> > Working with intel (TM) motherboards using the Intel Gb chips,
> > and talking to the intel reps last year (for my previous employer) I was
> > led to believe that
> > these chips supported IPMI by giving the BMC a back door into the same
> > NIC that the
> > OS was using.
> > (using an I2c (SMB) interface)
> > On the machines I used, I am pretty sure the bios gave the same MAC
> > address to the BMC
> > side of things as the OS side of theings by default, and we had is set
> > up so that we used the
> > same IP address also.
>
> well, i'm not positive about the MAC thing, but I am quite sure that on
> IBM xSeries systems you assigned a different IP address to the BMC,
> this was done in the BIOS. And, when I think about that, if it did have
> a seperate IP address then it musta had a seperate MAC too...
>
> Course, that was IBM hardware. I'll have to check up on this more
> at work tomorrow.
>
> So Julian, are you saying that you have seen this kind of functionality
> work on FreeBSD??
Hmm, well I've been told that using the same IP address or not should
both work :)
Matt, can you do a pciconf listing for me, I'd like to see exactly what
MAC you have. The most recent systems that are AMT capable
need some special code in the driver that FreeBSD doesnt yet have.
I'm wondering if that might be whats happening here.
Jack
_______________________________________________
freebsd-net@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-net
To unsubscribe, send any mail to "freebsd-net-unsubscribe@freebsd.org"
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?007b01c648f4$75eb41d0$75a31f9b>