Date: Mon, 02 Aug 2004 10:19:49 -0400 From: "Michael Roberts" <tpen0010@hotmail.com> To: geffy@geffychan.co.uk Cc: freebsd-mobile@freebsd.org Subject: Re: DLink DWL-G650 (h/w ver. B4) Message-ID: <BAY10-F36NzUP68zjBU0000e36b@hotmail.com>
next in thread | raw e-mail | index | archive | help
Hi, Thanks for the reply, and sorry for the delay - long weekend. If I put the card in before bootup, it will give the first set of errors that I listed during boot, then will give the "bfe0 timeout" errors after it has finished the boot scripts. So, that method doesn't work either. I haven't tried disabling my ethernet device.. though that's a good idea. How exactly do you do that? I tried "kldunload bfe", where bfe is my nic device, however that doesn't work, since bfe is built into the kernel. I tried syncing my sources and upgrading the kernel again, but something is broken in the sources, and the kernel doesn't compile even a GENERIC kernel. So, is there a way to unload a *part* of the kernel module -- namely bfe? Thanks for the help, it would be great if I could get this working. And it should work.... since it uses the ar5211.sys driver on the windows side, which means Atheros.... regards, Mike >From: Geffy <geffy@geffychan.co.uk> >To: Michael Roberts <tpen0010@hotmail.com> >Subject: Re: DLink DWL-G650 (h/w ver. B4) >Date: Fri, 30 Jul 2004 02:25:04 +0100 > >Michael Roberts wrote: >>Greetings, >> >>I got DLink DWL-G650 (h/w ver. B4) pc-card recently, which is supposed to >>run 802.11g using the atheros drivers. However, I've been trying to get >>it to work for the past three days w/o success. Other people on this list >>claim to have gotten it working, so any help would be much appreciated. > >I have it working on mine, but mine is version B3 Firmware 2.36 > >> >>My setup is: -current (from early July) on a Dell 8600, running a >>Broadcom ethernet interface on bfe0, and a kernel recompiled with "device >>ath" and "device ath_hal". >> >>When I put the Dlink card in, i get the following: >> >>cardbus0: Resource not specified in CIS: id=10, size=2000 >>bfe1: < Broadcom ... > irq 11 at device 0.0 on cardbus0 >>bfe1: BUG! Timeout waiting for bit 00000002 of register 42C to clear >>bfe1: MII without any PHY! >>device_attach: bfe1 attach returned 6 >>cbb0: Cardbus activation failed. > >What happens if you have the card in during bootup? That seems to be the >only way I can get it to work properly in mine. It also doesnt like my LAN >card operating, so I usually have to take that down prior to setting any IP >address or anything on the ath0 card. > >> >>Then a few seconds later I get something like >> >>bfe0: BUG! Timeout waiting for bit 00000002 of register 42C >> >>about 6 times, and then the computer freezes. The above line is not the >>exact output, since after the computer freezes, I can't copy the text >>(clearly..). >> >>Now, the above is strange because the card should be picked up by an >>atheros driver, not the bfe driver (note that bfe0 is my internal ethernet >>card, and the above is trying to assign the pccard to bfe1). I've tryed >>putting in hw.pccard.debug=1 and cis_debug=1, however the computer freezes >>before I get any output from those. >> >>I've read in other posts on the lists that the "Resource not specified" >>line is some sort of resource management issue, but no one has specified >>how to fix it. And that doesn't seem to address the other issue that the >>card isn't recognized by the atheros driver. >> >>So... I'm at a loss as to what to do. >> >>Any help would be much appreciated. >> >>regards, >>Mike >> >>_________________________________________________________________ >>FREE pop-up blocking with the new MSN Toolbar – get it now! >>http://toolbar.msn.click-url.com/go/onm00200415ave/direct/01/ >> >>_______________________________________________ >>freebsd-mobile@freebsd.org mailing list >>http://lists.freebsd.org/mailman/listinfo/freebsd-mobile >>To unsubscribe, send any mail to "freebsd-mobile-unsubscribe@freebsd.org" >> >> >> > >Let me know if that helps, I am sending this directly to you because my >hosting providers mailserver never seems able to send to the freebsd-mobile >mailing-list (mailserver problem my end, not the mailing list) > >Geoff _________________________________________________________________ Express yourself instantly with MSN Messenger! Download today - it's FREE! http://messenger.msn.click-url.com/go/onm00200471ave/direct/01/
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?BAY10-F36NzUP68zjBU0000e36b>