Date: Sun, 14 Nov 2004 22:14:44 +0100 (CET) From: Goran Gajic <ggajic@mail.sbb.co.yu> To: freebsd-amd64@FreeBSD.org Subject: Re: sk driver works fine 5.3rc2 - amd64 Message-ID: <Pine.BSF.4.60.0411142204350.51795@mail.sbb.co.yu> In-Reply-To: <20041114202359.GC11549@dragon.nuxi.com> References: <Pine.BSF.4.60.0411021020340.71690@mail.sbb.co.yu> <20041114202359.GC11549@dragon.nuxi.com>
next in thread | previous in thread | raw e-mail | index | archive | help
Hi,
It has integrated bge. As I have requested two NICs it was shipped
with sk as second NIC (I've looked at www.freebsd.org and card
was mentioned to be supported :) During tests with 5.3RC1 and 5.3RC2
I have installed third NIC xl0, just to see if it can operate in
case sk0 was unusable. Anyway, here is dmesg:
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.3-RELEASE #11: Sat Nov 13 20:41:48 UTC 2004
root@test.sbb.co.yu:/usr/src/sys/amd64/compile/MY
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Opteron(tm) Processor 248 (2191.72-MHz K8-class CPU)
Origin = "AuthenticAMD" Id = 0xf5a Stepping = 10
Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2>
AMD Features=0xe0500800<SYSCALL,NX,MMX+,LM,3DNow+,3DNow>
real memory = 3489071104 (3327 MB)
avail memory = 3364220928 (3208 MB)
ACPI APIC Table: <PTLTD APIC >
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
MADT: Forcing active-low polarity and level trigger for SCI
ioapic0 <Version 1.1> irqs 0-23 on motherboard
ioapic1 <Version 1.1> irqs 24-27 on motherboard
ioapic2 <Version 1.1> irqs 28-31 on motherboard
acpi0: <PTLTD XSDT> on motherboard
acpi0: Power Button (fixed)
acpi0: Sleep Button (fixed)
unknown: I/O range not supported
unknown: I/O range not supported
unknown: I/O range not supported
unknown: I/O range not supported
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x8008-0x800b on acpi0
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 6.0 on pci0
pci1: <ACPI PCI bus> on pcib1
ohci0: <OHCI (generic) USB controller> mem 0xd8104000-0xd8104fff irq 19 at
device 0.0 on pci1
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
ohci1: <OHCI (generic) USB controller> mem 0xd8105000-0xd8105fff irq 19 at
device 0.1 on pci1
ohci1: [GIANT-LOCKED]
usb1: OHCI version 1.0, legacy support
usb1: SMM does not respond, resetting
usb1: <OHCI (generic) USB controller> on ohci1
usb1: USB revision 1.0
uhub1: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 3 ports with 3 removable, self powered
xl0: <3Com 3c905B-TX Fast Etherlink XL> port 0x2000-0x207f mem
0xd8106800-0xd810687f irq 16 at device 10.0 on pci1
miibus0: <MII bus> on xl0
xlphy0: <3Com internal media interface> on miibus0
xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl0: Ethernet address: 00:50:04:23:c0:41
fwohci0: <Texas Instruments TSB43AB22/A> mem
0xd8100000-0xd8103fff,0xd8106000-0xd81067ff irq 19 at device 12.0 on pci1
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:e0:81:00:00:20:7d:5e
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:e0:81:20:7d:5e
fwe0: Ethernet address: 02:e0:81:20:7d:5e
fwe0: if_start running deferred for Giant
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <AMD 8111 UDMA133 controller> port
0x1440-0x144f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 7.1 on pci0
ata0: channel #0 on atapci0
ata1: channel #1 on atapci0
pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached)
pci0: <multimedia, audio> at device 7.5 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> at device 10.0 on pci0
pci2: <ACPI PCI bus> on pcib2
aac0: <Adaptec SCSI RAID 2120S> mem 0xdc000000-0xdfffffff irq 27 at device
8.0 on pci2
aac0: [FAST]
aac0: Enabling 64-bit address support
aac0: Unknown processor 100MHz, 48MB cache memory, optional battery not
installed
aac0: Kernel 4.1-0, Build 6251, S/N bcd1a6
aac0: Supported
Options=11d7e<CLUSTERS,WCACHE,DATA64,HOSTTIME,RAID50,WINDOW4GB,SOFTERR,SGMAP64,ALARM,NONDASD>
aacp0: <SCSI Passthrough Bus> on aac0
bge0: <Broadcom BCM5703 Gigabit Ethernet, ASIC rev. 0x1002> mem
0xd8200000-0xd820ffff irq 24 at device 9.0 on pci2
miibus1: <MII bus> on bge0
brgphy0: <BCM5703 10/100/1000baseTX PHY> on miibus1
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
1000baseTX-FDX, auto
bge0: Ethernet address: 00:e0:81:61:d3:66
pci0: <base peripheral, interrupt controller> at device 10.1 (no driver
attached)
pcib3: <ACPI PCI-PCI bridge> at device 11.0 on pci0
pci3: <ACPI PCI bus> on pcib3
skc0: <SysKonnect Gigabit Ethernet (V2.0)> port 0x3000-0x30ff mem
0xd8300000-0xd8303fff irq 29 at device 6.0 on pci3
skc0: SK-9521 V2.0 10/100/1000Base-T Adapter
skc0: PN: SK-9521 V2.0
skc0: EC: Rev. 1.2
skc0: MN: SysKonnect
skc0: SN: CAF12L49CD96B
sk0: <Marvell Semiconductor, Inc. Yukon> on skc0
sk0: Ethernet address: 00:00:5a:9c:d9:6b
miibus2: <MII bus> on sk0
e1000phy0: <Marvell 88E1000 Gigabit PHY> on miibus2
e1000phy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
1000baseTX-FDX, auto
pci0: <base peripheral, interrupt controller> at device 11.1 (no driver
attached)
pcib4: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pcib4: couldn't read bus number from cfg space
pcib4: trying bus number 4
pcib4: could not get PCI interrupt routing table for \\_SB_.PCIB -
AE_NOT_FOUND
pci4: <ACPI PCI bus> on pcib4
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on
acpi0
sio0: type 16550A, console
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
fdc0: <floppy drive controller> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on
acpi0
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0: <ECP parallel printer port> port 0x778-0x77f,0x378-0x37f irq 7 drq 3
on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
orm0: <ISA Option ROMs> at iomem
0xd4000-0xd57ff,0xcf800-0xd3fff,0xc0000-0xcf7ff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 0.976 msec
acd0: CDRW <HL-DT-ST RW/DVD GCC-4481B/1.03> at ata1-master UDMA33
aacd0: <RAID 5> on aac0
aacd0: 138800MB (284262400 sectors)
(probe11:aacp0:0:4:0): INQUIRY. CDB: 12 0 0 0 24 0
(probe11:aacp0:0:4:0): ILLEGAL REQUEST asc:55,3
(probe11:aacp0:0:4:0): Reserved ASC/ASCQ pair
(probe14:aacp0:0:8:0): INQUIRY. CDB: 12 0 0 0 24 0
(probe14:aacp0:0:8:0): ILLEGAL REQUEST asc:55,3
(probe14:aacp0:0:8:0): Reserved ASC/ASCQ pair
(probe18:aacp0:0:12:0): INQUIRY. CDB: 12 0 0 0 24 0
(probe18:aacp0:0:12:0): ILLEGAL REQUEST asc:55,3
(probe18:aacp0:0:12:0): Reserved ASC/ASCQ pair
(probe21:aacp0:0:15:0): INQUIRY. CDB: 12 0 0 0 24 0
(probe21:aacp0:0:15:0): ILLEGAL REQUEST asc:55,3
(probe21:aacp0:0:15:0): Reserved ASC/ASCQ pair
(probe7:aacp0:0:0:0): INQUIRY. CDB: 12 0 0 0 24 0
(probe7:aacp0:0:0:0): ILLEGAL REQUEST asc:55,3
(probe7:aacp0:0:0:0): Reserved ASC/ASCQ pair
(probe9:aacp0:0:2:0): INQUIRY. CDB: 12 0 0 0 24 0
(probe9:aacp0:0:2:0): ILLEGAL REQUEST asc:55,3
(probe9:aacp0:0:2:0): Reserved ASC/ASCQ pair
(probe10:aacp0:0:3:0): INQUIRY. CDB: 12 0 0 0 24 0
(probe10:aacp0:0:3:0): ILLEGAL REQUEST asc:55,3
(probe10:aacp0:0:3:0): Reserved ASC/ASCQ pair
(probe12:aacp0:0:5:0): INQUIRY. CDB: 12 0 0 0 24 0
(probe12:aacp0:0:5:0): ILLEGAL REQUEST asc:55,3
(probe12:aacp0:0:5:0): Reserved ASC/ASCQ pair
(probe13:aacp0:0:6:0): INQUIRY. CDB: 12 0 0 0 24 0
(probe13:aacp0:0:6:0): ILLEGAL REQUEST asc:55,3
(probe13:aacp0:0:6:0): Reserved ASC/ASCQ pair
(probe15:aacp0:0:9:0): INQUIRY. CDB: 12 0 0 0 24 0
(probe15:aacp0:0:9:0): ILLEGAL REQUEST asc:55,3
(probe15:aacp0:0:9:0): Reserved ASC/ASCQ pair
(probe16:aacp0:0:10:0): INQUIRY. CDB: 12 0 0 0 24 0
(probe16:aacp0:0:10:0): ILLEGAL REQUEST asc:55,3
(probe16:aacp0:0:10:0): Reserved ASC/ASCQ pair
(probe17:aacp0:0:11:0): INQUIRY. CDB: 12 0 0 0 24 0
(probe17:aacp0:0:11:0): ILLEGAL REQUEST asc:55,3
(probe17:aacp0:0:11:0): Reserved ASC/ASCQ pair
(probe19:aacp0:0:13:0): INQUIRY. CDB: 12 0 0 0 24 0
(probe19:aacp0:0:13:0): ILLEGAL REQUEST asc:55,3
(probe19:aacp0:0:13:0): Reserved ASC/ASCQ pair
(probe20:aacp0:0:14:0): INQUIRY. CDB: 12 0 0 0 24 0
(probe20:aacp0:0:14:0): ILLEGAL REQUEST asc:55,3
(probe20:aacp0:0:14:0): Reserved ASC/ASCQ pair
(probe8:aacp0:0:1:0): INQUIRY. CDB: 12 0 0 0 24 0
(probe8:aacp0:0:1:0): ILLEGAL REQUEST asc:55,3
(probe8:aacp0:0:1:0): Reserved ASC/ASCQ pair
SMP: AP CPU #1 Launched!
Mounting root from ufs:/dev/aacd0s1a
Regards,
gg.
p.s. I would like once again to thank Peter Edwards and Bjoern A.
Zeeb for all work done to make sk driver functional and stable.
On Sun, 14 Nov 2004, David O'Brien wrote:
> On Tue, Nov 02, 2004 at 10:25:03AM +0100, Goran Gajic wrote:
>> I have reported problems with sk driver in FreeBSD 5.3RC1 on amd64 on
>> Fujitsu Siemens Celsisu (dual amd64 box with 4 GB memory).
>
> Can you post your dmesg? The Fujitsu Siemens Celsisus is a Tyan K8W
> Thunder (s2885) based machine. Which means it has bge 5703, not sk
> on-board.
>
> --
> -- David (obrien@FreeBSD.org)
>
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.4.60.0411142204350.51795>