Date: Sat, 13 May 2000 17:32:51 -0400 (EDT) From: Thomas David Rivers <rivers@dignus.com> To: freebsd-questions@freebsd.org, pao-report@clave.gr.jp, rivers@dignus.com Subject: Re: Archtek PCMCIA "SmartLink" ethernet adapter. Message-ID: <200005132132.RAA35286@lakes.dignus.com> In-Reply-To: <200005132126.RAA35227@lakes.dignus.com>
next in thread | previous in thread | raw e-mail | index | archive | help
Oops - I neglected to provide the dumpcis output.
Here it is (again, from FreeBSD/PAO 3.4):
Configuration data for card in slot 0
Tuple #1, code = 0x1 (Common memory descriptor), length = 2
000: 00 ff
Common memory device information:
Device number 1, type No device, WPS = OFF
Speed = No speed, Memory block size = reserved, 32 units
Tuple #2, code = 0x15 (Version 1 info), length = 29
000: 04 01 50 43 4d 43 49 41 00 46 61 73 74 45 74 68
010: 65 72 6e 65 74 00 56 00 31 2e 30 00 ff
Version = 4.1, Manuf = [PCMCIA], card vers = [FastEthernet]
Addit. info = [V],[1.0]
Tuple #3, code = 0x20 (Manufacturer ID), length = 4
000: 1b 02 02 02
PCMCIA ID = 0x21b, OEM ID = 0x202
Tuple #4, code = 0x1a (Configuration map), length = 5
000: 01 01 c0 03 63
Reg len = 2, config register addr = 0x3c0, last config = 0x1
Registers: XX---XX-
Tuple #5, code = 0x1b (Configuration entry), length = 11
000: c7 81 19 07 55 4d 5d 65 30 ff ff
Config index = 0x7(default)
Interface byte = 0x81 (I/O) wait signal supported
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Minimum operating supply voltage: 4.5 x 1V
Maximum operating supply voltage: 5.5 x 1V
Card decodes 5 address lines, full 8/16 Bit I/O
IRQ modes: Level
IRQs: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Tuple #6, code = 0x1b (Configuration entry), length = 7
000: 07 08 ca 60 00 03 1f
Config index = 0x7
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x300 block length = 0x20
Tuple #7, code = 0x1b (Configuration entry), length = 7
000: 07 08 ca 60 20 03 1f
Config index = 0x7
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x320 block length = 0x20
Tuple #8, code = 0x1b (Configuration entry), length = 7
000: 07 08 ca 60 40 03 1f
Config index = 0x7
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x340 block length = 0x20
Tuple #9, code = 0x1b (Configuration entry), length = 7
000: 07 08 ca 60 60 03 1f
Config index = 0x7
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x360 block length = 0x20
Tuple #10, code = 0x1b (Configuration entry), length = 7
000: 07 08 ca 60 00 02 1f
Config index = 0x7
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x200 block length = 0x20
Tuple #11, code = 0x1b (Configuration entry), length = 7
000: 07 08 ca 60 20 02 1f
Config index = 0x7
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x220 block length = 0x20
Tuple #12, code = 0x21 (Functional ID), length = 2
000: 06 00
Network/LAN adapter
Tuple #13, code = 0x14 (No link), length = 0
Tuple #14, code = 0xff (Terminator), length = 0
2 slots found
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200005132132.RAA35286>