Date: Tue, 05 May 2009 01:07:13 +0100 From: Craig Butler <craig001@lerwick.hopto.org> To: Olev <hannula@gmail.com> Cc: freebsd-sparc@FreeBSD.org Subject: Re: 7.2-RELEASE working on Sun Fire V480R Message-ID: <1241482033.86830.2.camel@main.lerwick.hopto.org> In-Reply-To: <4b8db2420905040623o6af3a0c2je96954880a1d32d9@mail.gmail.com> References: <4b8db2420905040623o6af3a0c2je96954880a1d32d9@mail.gmail.com>
next in thread | previous in thread | raw e-mail | index | archive | help
nics are Cassini's I think... found-> vendor=0x108e, dev=0xabba, revid=0x11 Correct Marius ?? On Mon, 2009-05-04 at 16:23 +0300, Olev wrote: > As it is not listed in supported systems I gave it a shot. Installs > ok. Onboard ethernet not working. The machine I tested it on has 2x > PCI SCSI cards inside and it finds them too. Verbose dmesg below: > > Sun Fire 480R, No Keyboard > Copyright 2007 Sun Microsystems, Inc. All rights reserved. > OpenBoot 4.22.34, 4096 MB memory installed, Serial #53044977. > Ethernet address 0:3:ba:29:66:f1, Host ID: 832966f1. > > Rebooting with command: boot > Boot device: disk File and args: > > >> FreeBSD/sparc64 boot block > Boot path: /pci@9,600000/SUNW,qlc@2/fp@0,0/disk@w21000004cfb551b1,0:a > Boot loader: /boot/loader > Consoles: Open Firmware console > > Booting with sun4u support. > > FreeBSD/sparc64 bootstrap loader, Revision 1.0 > (root@obrian.cse.buffalo.edu, Fri May 1 14:51:37 UTC 2009) > bootpath="/pci@9,600000/SUNW,qlc@2/fp@0,0/disk@w21000004cfb551b1,0:a" > Loading /boot/defaults/loader.conf > /boot/kernel/kernel data=0x7c0348+0x78d48 syms=[0x8+0x823e0+0x8+0x70aa3] > / > Hit [Enter] to boot immediately, or any other key for command prompt. > Booting [/boot/kernel/kernel] in 8 seconds... > > Type '?' for a list of commands, 'help' for more detailed help. > OK boot -v > jumping to kernel entry at 0xc0078000. > Copyright (c) 1992-2009 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD is a registered trademark of The FreeBSD Foundation. > FreeBSD 7.2-RELEASE #0: Sat May 2 08:25:23 UTC 2009 > root@obrian.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC > Preloaded elf kernel "/boot/kernel/kernel" at 0xc092e000. > real memory = 4294967296 (4096 MB) > avail memory = 4174045184 (3980 MB) > machine: SUNW,Sun-Fire-480R > cpu0: Sun Microsystems UltraSparc-III+ Processor (900.00 MHz CPU) > mask=0x23 maxtl=5 maxwin=7 > initalizing intr_countp > cpu1: Sun Microsystems UltraSparc-III+ Processor (900.00 MHz CPU) > mask=0x23 maxtl=5 maxwin=7 > INTR: Adding CPU 1 as a target > FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs > wlan: <802.11 Link Layer> > firmware: 'isp_1000' version 1: 20142 bytes loaded at 0xc05fd180 > registered firmware set <isp_1000> > firmware: 'isp_1040' version 1: 22944 bytes loaded at 0xc060202e > registered firmware set <isp_1040> > firmware: 'isp_1040_it' version 1: 32942 bytes loaded at 0xc06079ce > registered firmware set <isp_1040_it> > firmware: 'isp_1080' version 1: 31350 bytes loaded at 0xc060fa7c > registered firmware set <isp_1080> > firmware: 'isp_1080_it' version 1: 40644 bytes loaded at 0xc06174f2 > registered firmware set <isp_1080_it> > firmware: 'isp_12160' version 1: 28050 bytes loaded at 0xc06213b6 > registered firmware set <isp_12160> > firmware: 'isp_12160_it' version 1: 40604 bytes loaded at 0xc0628148 > registered firmware set <isp_12160_it> > firmware: 'isp_2100' version 1: 76770 bytes loaded at 0xc0631fe4 > registered firmware set <isp_2100> > firmware: 'isp_2200' version 1: 77214 bytes loaded at 0xc0644bc6 > registered firmware set <isp_2200> > firmware: 'isp_2300' version 1: 105078 bytes loaded at 0xc0657964 > registered firmware set <isp_2300> > firmware: 'isp_2322' version 1: 108856 bytes loaded at 0xc06713da > registered firmware set <isp_2322> > firmware: 'isp_2400' version 1: 172952 bytes loaded at 0xc068ef94 > registered firmware set <isp_2400> > random: <entropy source, Software, Yarrow> > kbd0 at kbdmux0 > nfslock: pseudo-device > mem: <memory> > null: <null device, zero device> > openfirm: <Open Firmware control device> > nexus0: <Open Firmware Nexus device> > nexus0: <memory-controller> mem 0x40000400000-0x40000400047 type > memory-controller (no driver attached) > nexus0: <memory-controller> mem 0x40001400000-0x40001400047 type > memory-controller (no driver attached) > pcib0: <Sun Host-PCI bridge> mem > 0x40004700000-0x40004717fff,0x40004410000-0x4000441004f,0x7ffee000000-0x7ffee0000ff > irq 563,560,561,564,565 on nexus0 > pcib0: Schizo, version 4, IGN 0x8, bus B, 33MHz > pcib0: DVMA map: 0xc0000000 to 0xffffffff > pcib0: bus range 0 to 0; PCI bus 0 > pcib0: [FILTER] > pci0: <OFW PCI bus> on pcib0 > pci0: domain=0, physical bus=0 > found-> vendor=0x108e, dev=0x8001, revid=0x00 > domain=0, bus=0, slot=0, func=0 > class=06-00-00, hdrtype=0x00, mfdev=0 > cmdreg=0x0146, statreg=0x0280, cachelnsz=0 (dwords) > lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) > found-> vendor=0x1000, dev=0x000f, revid=0x14 > domain=0, bus=0, slot=3, func=0 > class=01-00-00, hdrtype=0x00, mfdev=1 > cmdreg=0x0146, statreg=0x0200, cachelnsz=16 (dwords) > lattimer=0x88 (4080 ns), mingnt=0x11 (4250 ns), maxlat=0x40 (16000 ns) > intpin=a, irq=255 > map[10]: type I/O Port, range 32, base 0x300, size 8, port disabled > map[14]: type Memory, range 32, base 0x100000, size 8, enabled > map[18]: type Memory, range 32, base 0x102000, size 12, enabled > found-> vendor=0x1000, dev=0x000f, revid=0x14 > domain=0, bus=0, slot=3, func=1 > class=01-00-00, hdrtype=0x00, mfdev=1 > cmdreg=0x0146, statreg=0x0200, cachelnsz=16 (dwords) > lattimer=0x88 (4080 ns), mingnt=0x11 (4250 ns), maxlat=0x40 (16000 ns) > intpin=b, irq=255 > map[10]: type I/O Port, range 32, base 0x400, size 8, port disabled > map[14]: type Memory, range 32, base 0x104000, size 8, enabled > map[18]: type Memory, range 32, base 0x106000, size 12, enabled > found-> vendor=0x1000, dev=0x000f, revid=0x14 > domain=0, bus=0, slot=4, func=0 > class=01-00-00, hdrtype=0x00, mfdev=1 > cmdreg=0x0146, statreg=0x0200, cachelnsz=16 (dwords) > lattimer=0x88 (4080 ns), mingnt=0x11 (4250 ns), maxlat=0x40 (16000 ns) > intpin=a, irq=255 > map[10]: type I/O Port, range 32, base 0x500, size 8, port disabled > map[14]: type Memory, range 32, base 0x108000, size 8, enabled > map[18]: type Memory, range 32, base 0x10a000, size 12, enabled > found-> vendor=0x1000, dev=0x000f, revid=0x14 > domain=0, bus=0, slot=4, func=1 > class=01-00-00, hdrtype=0x00, mfdev=1 > cmdreg=0x0146, statreg=0x0200, cachelnsz=16 (dwords) > lattimer=0x88 (4080 ns), mingnt=0x11 (4250 ns), maxlat=0x40 (16000 ns) > intpin=b, irq=255 > map[10]: type I/O Port, range 32, base 0x600, size 8, port disabled > map[14]: type Memory, range 32, base 0x10c000, size 8, enabled > map[18]: type Memory, range 32, base 0x10e000, size 12, enabled > found-> vendor=0x1095, dev=0x0646, revid=0x07 > domain=0, bus=0, slot=6, func=0 > class=01-01-8f, hdrtype=0x00, mfdev=0 > cmdreg=0x0000, statreg=0x0290, cachelnsz=0 (dwords) > lattimer=0x10 (480 ns), mingnt=0x02 (500 ns), maxlat=0x04 (1000 ns) > intpin=a, irq=255 > powerspec 1 supports D0 D1 D2 D3 current D0 > map[10]: type I/O Port, range 32, base 0x700, size 3, port disabled > map[14]: type I/O Port, range 32, base 0x718, size 2, enabled > map[18]: type I/O Port, range 32, base 0x710, size 3, enabled > map[1c]: type I/O Port, range 32, base 0x708, size 2, enabled > map[20]: type I/O Port, range 32, base 0x720, size 4, enabled > sym0: <875> port 0x300-0x3ff mem 0x100000-0x1000ff,0x102000-0x102fff > at device 3.0 on pci0 > sym0: Reserved 0x100 bytes for rid 0x14 type 3 at 0x100000 > sym0: Reserved 0x1000 bytes for rid 0x18 type 3 at 0x102000 > sym0: chip clock is 40218KHz > sym0: No NVRAM, ID 7, Fast-20, SE, parity checking > sym0: open drain IRQ line driver, using on-chip SRAM > sym0: using LOAD/STORE-based firmware. > sym0: [MPSAFE] > sym0: [ITHREAD] > sym1: <875> port 0x400-0x4ff mem 0x104000-0x1040ff,0x106000-0x106fff > at device 3.1 on pci0 > sym1: Reserved 0x100 bytes for rid 0x14 type 3 at 0x104000 > sym1: Reserved 0x1000 bytes for rid 0x18 type 3 at 0x106000 > sym1: chip clock is 40218KHz > sym1: No NVRAM, ID 7, Fast-20, SE, parity checking > sym1: open drain IRQ line driver, using on-chip SRAM > sym1: using LOAD/STORE-based firmware. > sym1: [MPSAFE] > sym1: [ITHREAD] > sym2: <875> port 0x500-0x5ff mem 0x108000-0x1080ff,0x10a000-0x10afff > at device 4.0 on pci0 > sym2: Reserved 0x100 bytes for rid 0x14 type 3 at 0x108000 > sym2: Reserved 0x1000 bytes for rid 0x18 type 3 at 0x10a000 > sym2: chip clock is 40218KHz > sym2: No NVRAM, ID 7, Fast-20, SE, parity checking > sym2: open drain IRQ line driver, using on-chip SRAM > sym2: using LOAD/STORE-based firmware. > sym2: [MPSAFE] > sym2: [ITHREAD] > sym3: <875> port 0x600-0x6ff mem 0x10c000-0x10c0ff,0x10e000-0x10efff > at device 4.1 on pci0 > sym3: Reserved 0x100 bytes for rid 0x14 type 3 at 0x10c000 > sym3: Reserved 0x1000 bytes for rid 0x18 type 3 at 0x10e000 > sym3: chip clock is 40218KHz > sym3: No NVRAM, ID 7, Fast-20, SE, parity checking > sym3: open drain IRQ line driver, using on-chip SRAM > sym3: using LOAD/STORE-based firmware. > sym3: [MPSAFE] > sym3: [ITHREAD] > atapci0: <SiI CMD 646U2 UDMA33 controller> port > 0x700-0x707,0x718-0x71b,0x710-0x717,0x708-0x70b,0x720-0x72f at device > 6.0 on pci0 > atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x720 > pcib0: belatedly registered as interrupt controller for vector 0x208 > atapci0: [MPSAFE] > atapci0: [ITHREAD] > atapci0: HW has secondary channel disabled > ata2: <ATA channel 0> on atapci0 > atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x700 > atapci0: Reserved 0x4 bytes for rid 0x14 type 4 at 0x718 > ata2: reset tp1 mask=03 ostat0=00 ostat1=00 > ata2: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb > ata2: stat1=0x00 err=0x04 lsb=0x00 msb=0x00 > ata2: reset tp2 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER> > ata2: [MPSAFE] > ata2: [ITHREAD] > pcib1: <Sun Host-PCI bridge> mem > 0x40004600000-0x40004617fff,0x40004410000-0x4000441004f,0x7ffec000000-0x7ffec0000ff > irq 562,560,561,564,566 on nexus0 > pcib1: Schizo, version 4, IGN 0x8, bus A, 66MHz > Timecounter "pcib1" frequency 150000000 Hz quality 100 > pcib1: DVMA map: 0xc0000000 to 0xffffffff > pcib1: bus range 0 to 0; PCI bus 0 > pcib1: [FILTER] > pcib1: [FILTER] > pcib1: [FILTER] > pcib1: [FILTER] > pci1: <OFW PCI bus> on pcib1 > pci1: domain=1, physical bus=0 > found-> vendor=0x108e, dev=0x8001, revid=0x00 > domain=1, bus=0, slot=0, func=0 > class=06-00-00, hdrtype=0x00, mfdev=0 > cmdreg=0x0146, statreg=0x02a0, cachelnsz=0 (dwords) > lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) > pcib2: <Sun Host-PCI bridge> mem > 0x40004f00000-0x40004f17fff,0x40004c10000-0x40004c1004f,0x7ffea000000-0x7ffea0000ff > irq 627,624,625,628,629 on nexus0 > pcib2: Schizo, version 4, IGN 0x9, bus B, 33MHz > pcib2: DVMA map: 0xc0000000 to 0xffffffff > pcib2: bus range 0 to 0; PCI bus 0 > pcib2: [FILTER] > pci2: <OFW PCI bus> on pcib2 > pci2: domain=2, physical bus=0 > found-> vendor=0x108e, dev=0x8001, revid=0x00 > domain=2, bus=0, slot=0, func=0 > class=06-00-00, hdrtype=0x00, mfdev=0 > cmdreg=0x0146, statreg=0x0280, cachelnsz=0 (dwords) > lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) > found-> vendor=0x108e, dev=0x1100, revid=0x01 > domain=2, bus=0, slot=1, func=0 > class=06-80-00, hdrtype=0x00, mfdev=1 > cmdreg=0x0146, statreg=0x0280, cachelnsz=16 (dwords) > lattimer=0x50 (2400 ns), mingnt=0x0a (2500 ns), maxlat=0x19 (6250 ns) > map[10]: type Memory, range 32, base 0x7d000000, size 24, enabled > map[14]: type Memory, range 32, base 0x7e000000, size 23, enabled > found-> vendor=0x108e, dev=0x1103, revid=0x01 > domain=2, bus=0, slot=1, func=3 > class=0c-03-10, hdrtype=0x00, mfdev=1 > cmdreg=0x0000, statreg=0x0280, cachelnsz=16 (dwords) > lattimer=0x50 (2400 ns), mingnt=0x0a (2500 ns), maxlat=0x05 (1250 ns) > map[10]: type Memory, range 32, base 0x1000000, size 15, memory disabled > found-> vendor=0x108e, dev=0xabba, revid=0x11 > domain=2, bus=0, slot=2, func=0 > class=02-00-00, hdrtype=0x00, mfdev=0 > cmdreg=0x0144, statreg=0x04a0, cachelnsz=16 (dwords) > lattimer=0xff (7650 ns), mingnt=0x40 (16000 ns), maxlat=0x40 (16000 ns) > intpin=a, irq=255 > map[10]: type Memory, range 32, base 0x200000, size 21, memory disabled > ebus0: <PCI-EBus3 bridge> mem > 0x7d000000-0x7dffffff,0x7e000000-0x7e7fffff at device 1.0 on pci2 > ebus0: Reserved 0x1000000 bytes for rid 0x10 type 3 at 0x7d000000 > ebus0: Reserved 0x800000 bytes for rid 0x14 type 3 at 0x7e000000 > ebus0: <flashprom> addr 0-0x1fffff (no driver attached) > ebus0: <bbc> addr 0x100000000-0x1000fffff (no driver attached) > ebus0: <power> addr 0x10030002e-0x10030002f,0x100300600-0x100300607 > (no driver attached) > ebus0: <i2c> addr 0x10000002e-0x10000002f,0x10000002d irq 35 (no > driver attached) > ebus0: <i2c> addr 0x100000030-0x100000031 irq 35 (no driver attached) > rtc0: <Real-Time Clock> addr 0x100300070-0x100300071 irq 36 on ebus0 > rtc0: registered as a time-of-day clock (resolution 1000000us) > rtc0: invalid timeebus0: <gpio> addr 0x100300600-0x100300607 (no > driver attached) > ebus0: <pmc> addr 0x100300700-0x100300701 (no driver attached) > uart0: <16550 or compatible> addr 0x1003062f8-0x1003062ff irq 46 on ebus0 > uart0: [FILTER] > uart0: fast interrupt > uart1: <16550 or compatible> addr 0x1003083f8-0x1003083ff irq 45 on ebus0 > uart1: [FILTER] > uart1: fast interrupt > scc0: <Siemens SAB 82532 dual channel SCC> addr > 0x100400000-0x10040007f irq 34 on ebus0 > scc0: not resetting hardware > scc0: [FILTER] > uart2: <SAB 82532 v3.2, channel A> on scc0 > uart2: [FILTER] > uart2: CTS oflow > uart2: fast interrupt > uart2: console (9600,n,8,1) > uart3: <SAB 82532 v3.2, channel B> on scc0 > uart3: [FILTER] > uart3: CTS oflow > uart3: fast interrupt > scc0: fast interrupt > ohci0: <Sun PCIO-2 USB controller> mem 0x1000000-0x1007fff at device 1.3 on pci2 > ohci0: Reserved 0x8000 bytes for rid 0x10 type 3 at 0x1000000 > ohci0: (New OHCI DeviceId=0x1103108e) > ohci0: [GIANT-LOCKED] > ohci0: [ITHREAD] > usb0: OHCI version 1.0, legacy support > usb0: <Sun PCIO-2 USB controller> on ohci0 > usb0: USB revision 1.0 > uhub0: <(0x108e) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0 > uhub0: 4 ports with 4 removable, self powered > pci2: <network, ethernet> at device 2.0 (no driver attached) > pcib3: <Sun Host-PCI bridge> mem > 0x40004e00000-0x40004e17fff,0x40004c10000-0x40004c1004f,0x7ffe8000000-0x7ffe80000ff > irq 626,624,625,628,630 on nexus0 > pcib3: Schizo, version 4, IGN 0x9, bus A, 66MHz > Timecounter "pcib3" frequency 150000000 Hz quality 100 > pcib3: DVMA map: 0xc0000000 to 0xffffffff > pcib3: bus range 0 to 0; PCI bus 0 > pcib3: [FILTER] > pcib3: [FILTER] > pcib3: [FILTER] > pcib3: [FILTER] > pci3: <OFW PCI bus> on pcib3 > pci3: domain=3, physical bus=0 > found-> vendor=0x108e, dev=0x8001, revid=0x00 > domain=3, bus=0, slot=0, func=0 > class=06-00-00, hdrtype=0x00, mfdev=0 > cmdreg=0x0146, statreg=0x02a0, cachelnsz=0 (dwords) > lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) > found-> vendor=0x108e, dev=0xabba, revid=0x11 > domain=3, bus=0, slot=1, func=0 > class=02-00-00, hdrtype=0x00, mfdev=0 > cmdreg=0x0144, statreg=0x04a0, cachelnsz=16 (dwords) > lattimer=0xff (7650 ns), mingnt=0x40 (16000 ns), maxlat=0x40 (16000 ns) > intpin=a, irq=255 > map[10]: type Memory, range 32, base 0x200000, size 21, memory disabled > found-> vendor=0x1077, dev=0x2200, revid=0x05 > domain=3, bus=0, slot=2, func=0 > class=01-00-00, hdrtype=0x00, mfdev=0 > cmdreg=0x0000, statreg=0x02b0, cachelnsz=16 (dwords) > lattimer=0xf8 (7440 ns), mingnt=0x40 (16000 ns), maxlat=0x00 (0 ns) > intpin=a, irq=255 > powerspec 1 supports D0 D3 current D0 > map[10]: type I/O Port, range 32, base 0x300, size 8, port disabled > map[14]: type Memory, range 32, base 0x400000, size 12, memory disabled > pci3: <network, ethernet> at device 1.0 (no driver attached) > Qlogic ISP Driver, FreeBSD Version 5.9, Core Version 3.0 > isp0: <Qlogic ISP 2200 PCI FC-AL Adapter> port 0x300-0x3ff mem > 0x400000-0x400fff at device 2.0 on pci3 > isp0: Reserved 0x1000 bytes for rid 0x14 type 3 at 0x400000 > isp0: using Memory space register mapping > isp0: [MPSAFE] > isp0: [ITHREAD] > isp0: Board Type 2200, Chip Revision 0x5, loaded F/W Revision 2.2.6 > isp0: Last F/W revision was 2.1.105 > isp0: 309 max I/O command limit set > isp0: invalid NVRAM header > isp0: invalid NVRAM header > isp0: Using Node WWN 0x400000007f000009 > isp0: Using Port WWN 0x400000007f000009 > syscons0: no video adapter found. > nexus0: <syscons> type unknown (no driver attached) > Reducing kern.maxvnodes 134011 -> 100000 > procfs registered > Timecounter "tick" frequency 900000000 Hz quality 10 > Timecounters tick every 1.000 msec > lo0: bpf attached > isp0: LIP Received > isp0: Loop UP > isp0: Port Database Changed > ata2-master: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=80 wire > isp0: Firmware State <Config Wait->Ready> > acd0: setting PIO4 on CMD 646U2 chip > isp0: HBA PortID 0x000029 N-Port Handle 109, Connection Topology 'Private Loop' > isp0: HBA WWNN 0x400000007f000009 HBA WWPN 0x400000007f000009 > isp0: PortID 0x0000ef handle 0x0 role Target arrived at tgt 0 > WWNN 0x20000004cfb551b1 WWPN 0x21000004cfb551b1 > isp0: PortID 0x0000e8 handle 0x1 role Target arrived at tgt 1 > WWNN 0x20000004cfb558ed WWPN 0x21000004cfb558ed > acd0: <TOSHIBA DVD-ROM SD-C2512/1013> DVDR drive at ata2 as master > acd0: read 4134KB/s (4134KB/s) write 172KB/s, 512KB buffer, PIO4 > acd0: Reads: CDDA > acd0: Writes: CDR, CDRW, DVDR, DVDRAM, test write > acd0: Audio: play, 16 volume levels > acd0: Mechanism: ejectable tray, unlocked > acd0: Medium: no/blank disc > Waiting 5 seconds for SCSI devices to settle > (noperiph:sym0:0:-1:-1): SCSI BUS reset delivered. > (noperiph:sym1:0:-1:-1): SCSI BUS reset delivered. > (noperiph:sym2:0:-1:-1): SCSI BUS reset delivered. > (noperiph:sym3:0:-1:-1): SCSI BUS reset delivered. > (probe0:isp0:0:0:0): Retrying Command > (probe1:isp0:0:1:0): Retrying Command > pass0 at isp0 bus 0 target 0 lun 0 > pass0: <SEAGATE ST336605FSUN36G 0638> Fixed Direct Access SCSI-3 device > pass0: Serial Number 3FP233TR00007316NY71 > pass0: 100.000MB/s transfers > pass0: Command Queueing Enabled > pass1 at isp0 bus 0 target 1 lun 0 > pass1: <SEAGATE ST336605FSUN36G 0638> Fixed Direct Access SCSI-3 device > pass1: Serial Number 3FP239L000007315HL0H > pass1: 100.000MB/s transfers WWNN 0x20000004cfb558ed WWPN > 0x21000004cfb558ed PortID 0xe8 > pass1: Command Queueing Enabled > GEOM: new disk da0 > GEOM: new disk da1 > da0 at isp0 bus 0 target 0 lun 0 > da0: <SEAGATE ST336605FSUN36G 0638> Fixed Direct Access SCSI-3 device > da0: Serial Number 3FP233TR00007316NY71 > da0: 100.000MB/s transfers > da0: Command Queueing Enabled > da0: 34732MB (71132959 512 byte sectors: 255H 63S/T 4427C) > da1 at isp0 bus 0 target 1 lun 0 > da1: <SEAGATE ST336605FSUN36G 0638> Fixed Direct Access SCSI-3 device > da1: Serial Number 3FP239L000007315HL0H > da1: 100.000MB/s transfers WWNN 0x20000004cfb558ed WWPN > 0x21000004cfb558ed PortID 0xe8 > da1: Command Queueing Enabled > da1: 34732MB (71132959 512 byte sectors: 255H 63S/T 4427C) > SMP: AP CPU #1 Launched! > _______________________________________________ > freebsd-sparc64@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-sparc64 > To unsubscribe, send any mail to "freebsd-sparc64-unsubscribe@freebsd.org"
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?1241482033.86830.2.camel>