Date: Wed, 28 Aug 1996 15:43:40 -0700 (PDT) From: Steve Khoo <steve@gordian.com> To: freebsd-current@freebsd.org Cc: freebsd-scsi@freebsd.org, se@ZPR.Uni-Koeln.DE Subject: Re: problems booting with 2 drives on NCR8251D Message-ID: <199608282243.PAA19057@delphi.gordian.com> In-Reply-To: Steve Khoo's message of Mon, 26 Aug 1996 12:15:09 -0700 (PDT) References: <199608261915.MAA10702@delphi.gordian.com>
next in thread | previous in thread | raw e-mail | index | archive | help
FYI:
Well, I didn't get any response on this, but finally tracked down the
problem to a flaky pin on one of the 68pin FWD SCSI connectors.
SEK
>>>>> "Steve" == Steve Khoo <steve@gordian.com> writes:
Steve> setup:
Steve> Asus MB(P55TP4XEG) 512K Cache
Steve> 32MB RAM
Steve> Fast Wide Differential SCSI Controller (NCR8251D)
Steve> Seagate ST12550WD on SCSI ID #0
Steve> Seagate ST15150WD on SCSI ID #1
Steve> The system is running FreeBSD 2.2-CURRENT sup'd on 8/17/96.
Steve> The system boots and runs find with just the first(Seagate
Steve> ST12550WD) drive. When I added the second(Seagate
Steve> ST15150WD) drive I get the following errors. I can boot
Steve> dos and do fdisk/format and stuff on the second drive
Steve> without any problems. Any ideas what the errors mean?
Steve> I'd appreciate any help.
Steve> Thanks!
Steve> SEK
Steve> FreeBSD 2.2-CURRENT #0: Mon Aug 19 12:48:53 PDT 1996
Steve> steve@metis.gordian.com:/usr/src/sys/compile/metis
Steve> Calibrating clock(s) relative to mc146818A clock...
Steve> i586 clock: 99465569 Hz, i8254 clock: 1193086 Hz
Steve> CPU: Pentium (99.47-MHz 586-class CPU)
Steve> Origin = "GenuineIntel" Id = 0x525 Stepping=5
Steve> Features=0x1bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8>
Steve> real memory = 33554432 (32768K bytes)
Steve> avail memory = 30695424 (29976K bytes)
Steve> Probing for devices on PCI bus 0:
Steve> chip0 <Intel 82437 (Triton) PCI cache memory controller> rev 2 on pci0:0
Steve> chip1 <Intel 82371 (Triton) PCI-ISA bridge> rev 2 on pci0:7:0
Steve> pci0:7:1: Intel Corporation, device=0x1230, class=storage (ide) [no driver assigned]
Steve> de0 <Digital DC21140 Fast Ethernet> rev 18 int a irq 12 on pci0:9
Steve> de0: SMC 9332 DC21140 [10-100Mb/s] pass 1.2
Steve> de0: address 00:00:c0:58:c3:e4
Steve> de0: enabling 10baseT port
Steve> ncr0 <ncr 53c825 wide scsi> rev 2 int a irq 10 on pci0:10
Steve> ncr0 waiting for scsi devices to settle
Steve> (ncr0:0:0): "SEAGATE ST12550W 0004" type 0 fixed SCSI 2
Steve> sd0(ncr0:0:0): Direct-Access
Steve> sd0(ncr0:0:0): WIDE SCSI (16 bit) enabled.
Steve> sd0(ncr0:0:0): FAST SCSI-2 100ns (10 Mb/sec) offset 8.
Steve> 2040MB (4178874 512 byte sectors)
Steve> (ncr0:1:0): "SEAGATE ST15150W 0023" type 0 fixed SCSI 2
Steve> sd1(ncr0:1:0): Direct-Access
Steve> sd1(ncr0:1:0): WIDE SCSI (16 bit) enabled.
Steve> ncr0:1: ERROR (80:91) (9-ae-0) (0/1b) @ (d8c:19000004).
Steve> script cmd = 89030000
Steve> reg: da 10 80 1b 47 00 01 07 23 09 81 ae 80 00 0e 08.
Steve> ncr0: restart (fatal error).
Steve> sd1(ncr0:1:0): COMMAND FAILED (9 ff) @f109b400.
Steve> ncr0: aborting job ...
Steve> ncr0:0: ERROR (90:0) (8-a6-0) (0/13) @ (418:43000060).
Steve> script cmd = 878b0000
Steve> reg: da 00 00 13 47 00 01 07 31 08 01 a6 80 00 0e 0a.
Steve> ncr0: restart (fatal error).
Steve> sd1(ncr0:1:0): COMMAND FAILED (9 ff) @f109b400.
Steve> ncr0: aborting job ...
Steve> ncr0:0: ERROR (90:0) (8-a6-0) (0/13) @ (418:43000060).
Steve> script cmd = 878b0000
Steve> reg: da 00 00 13 47 00 01 07 31 08 01 a6 80 00 0e 0a.
Steve> ncr0: restart (fatal error).
Steve> sd1(ncr0:1:0): COMMAND FAILED (9 ff) @f109b400.
Steve> ncr0: aborting job ...
Steve> ncr0:0: ERROR (90:0) (8-a6-0) (0/13) @ (418:43000060).
Steve> script cmd = 878b0000
Steve> reg: da 00 00 13 47 00 01 07 31 08 01 a6 80 00 0e 0a.
Steve> ncr0: restart (fatal error).
Steve> sd1(ncr0:1:0): COMMAND FAILED (9 ff) @f109b400.
Steve> ncr0: aborting job ...
Steve> ncr0:0: ERROR (90:0) (8-a6-0) (0/13) @ (418:43000060).
Steve> script cmd = 878b0000
Steve> reg: da 00 00 13 47 00 01 07 31 08 01 a6 80 00 0e 0a.
Steve> ncr0: restart (fatal error).
Steve> sd1(ncr0:1:0): COMMAND FAILED (9 ff) @f109b400.
Steve> sd1 could not mode sense (4). Using ficticious geometry
Steve> ncr0: aborting job ...
Steve> ncr0:0: ERROR (90:0) (8-a6-0) (0/13) @ (418:43000060).
Steve> script cmd = 878b0000
Steve> reg: da 00 00 13 47 00 01 07 31 08 01 a6 80 00 0e 0a.
Steve> ncr0: restart (fatal error).
Steve> sd1(ncr0:1:0): COMMAND FAILED (9 ff) @f109b400.
Steve> ncr0: aborting job ...
Steve> ncr0:0: ERROR (90:0) (8-a6-0) (0/13) @ (418:43000060).
Steve> script cmd = 878b0000
Steve> reg: da 00 00 13 47 00 01 07 31 08 01 a6 80 00 0e 0a.
Steve> ncr0: restart (fatal error).
Steve> sd1(ncr0:1:0): COMMAND FAILED (9 ff) @f109b400.
Steve> ncr0: aborting job ...
Steve> ncr0:0: ERROR (90:0) (8-a6-0) (0/13) @ (418:43000060).
Steve> script cmd = 878b0000
Steve> reg: da 00 00 13 47 00 01 07 31 08 01 a6 80 00 0e 0a.
Steve> ncr0: restart (fatal error).
Steve> sd1(ncr0:1:0): COMMAND FAILED (9 ff) @f109b400.
Steve> ncr0: aborting job ...
Steve> ncr0:0: ERROR (90:0) (8-a6-0) (0/13) @ (418:43000060).
Steve> script cmd = 878b0000
Steve> reg: da 00 00 13 47 00 01 07 31 08 01 a6 80 00 0e 0a.
Steve> ncr0: restart (fatal error).
Steve> sd1(ncr0:1:0): COMMAND FAILED (9 ff) @f109b400.
Steve> ncr0: aborting job ...
Steve> ncr0:0: ERROR (90:0) (8-a6-0) (0/13) @ (418:43000060).
Steve> script cmd = 878b0000
Steve> reg: da 00 00 13 47 00 01 07 31 08 01 a6 80 00 0e 0a.
Steve> ncr0: restart (fatal error).
Steve> sd1(ncr0:1:0): COMMAND FAILED (9 ff) @f109b400.
Steve> sd1: could not get size
Steve> 0MB (0 512 byte sectors)
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?199608282243.PAA19057>