Date: Tue, 8 Sep 2009 14:33:35 -0700 From: Pyun YongHyeon <pyunyh@gmail.com> To: freebsd-net@freebsd.org Subject: Re: D-Link DGE-560SX (Marvell 88E8061-based) doesn't see link Message-ID: <20090908213335.GE1520@michelle.cdnetworks.com> In-Reply-To: <20090908075030.GA6644@traktor.dnepro.net> References: <20090821221932.GE1262@michelle.cdnetworks.com> <20090825083857.GA22983@traktor.dnepro.net> <20090825114649.GA11642@traktor.dnepro.net> <20090825130821.GA41669@traktor.dnepro.net> <20090825182553.GD1282@michelle.cdnetworks.com> <20090826093916.GB10790@traktor.dnepro.net> <20090826094856.GC10790@traktor.dnepro.net> <20090901161310.GA37481@traktor.dnepro.net> <20090904212223.GA9950@michelle.cdnetworks.com> <20090908075030.GA6644@traktor.dnepro.net>
next in thread | previous in thread | raw e-mail | index | archive | help
On Tue, Sep 08, 2009 at 10:50:30AM +0300, Eugene Perevyazko wrote: > On Fri, Sep 04, 2009 at 02:22:23PM -0700, Pyun YongHyeon wrote: > > > > Would you back out previous changes and apply the patch at the > > following URL? > > http://people.freebsd.org/~yongari/msk/msk.DGE560.diff2 > > > > Note, I have no more access to msk(4) hardwares so it wasn't tested > > at all except compilation. > > > > Still no success. > > mskc0: <D-Link 560SX Gigabit Ethernet> port 0xd800-0xd8ff mem 0xfeafc000-0xfeafffff irq 16 at device 0.0 on pci1 > msk0: <Marvell Technology Group Ltd. Yukon XL Id 0xb3 Rev 0x03> on mskc0 > msk0: Ethernet address: 00:21:91:52:4f:09 > miibus0: <MII bus> on msk0 > e1000phy0: <Marvell 88E1112 Gigabit PHY> PHY 0 on miibus0 > e1000phy0: 1000baseSX, 1000baseSX-FDX, auto > mskc0: [FILTER] > > ifconfig -m msk0 > msk0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 > options=11a<TXCSUM,VLAN_MTU,VLAN_HWTAGGING,TSO4> > capabilities=11a<TXCSUM,VLAN_MTU,VLAN_HWTAGGING,TSO4> > ether 00:21:91:52:4f:09 > inet 10.2.3.1 netmask 0xffffff00 broadcast 10.2.3.255 > media: Ethernet autoselect (autoselect <full-duplex>) > status: active > supported media: > media autoselect > media 1000baseSX mediaopt full-duplex > media 1000baseSX > media none > > Switch shows no link on the port. > > # ifconfig msk0 media 1000baseSX mediaopt full-duplex > # ifconfig msk0 > msk0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 > options=11a<TXCSUM,VLAN_MTU,VLAN_HWTAGGING,TSO4> > ether 00:21:91:52:4f:09 > inet 10.2.3.1 netmask 0xffffff00 broadcast 10.2.3.255 > media: Ethernet 1000baseSX <full-duplex> (autoselect <full-duplex>) > status: active > > Switch shows no link again. > > All dev.msk.0.stats counters are zero even after trying broadcast ping. > > I can arrange you root access to the host with this NIC if you have time/wish. > I've sent mail in private. > -- > Eugene Perevyazko
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20090908213335.GE1520>