Date: Sun, 2 Oct 2022 12:06:14 -0700 From: bob prohaska <fbsd@www.zefox.net> To: Mark Millard <marklmi@yahoo.com> Cc: freebsd-arm <freebsd-arm@freebsd.org>, freebsd-uboot@freebsd.org Subject: Re: u-boot debug, was: Re: U-boot on RPI3, sees disk but won't boot it Message-ID: <20221002190614.GA2704@www.zefox.net> In-Reply-To: <20221002182049.GA2255@www.zefox.net> References: <197D3C46-063B-4C67-AB1A-A3A072521D7F@yahoo.com> <A8C2BA4E-4520-4B34-9614-DDC4D8BEB097@yahoo.com> <6AA65AE6-41F1-405F-A592-7D641EA4C9CF@yahoo.com> <E3A1C678-8C47-4283-9F9F-4C9011DB8A2B@yahoo.com> <20221001174724.GA98055@www.zefox.net> <ABFDD634-5CB6-4DAE-B4DE-629CE7E4FE06@yahoo.com> <20221001193033.GA98348@www.zefox.net> <46226720-D867-4AD3-9559-A4365FAC28C4@yahoo.com> <6DB88FC9-629C-43E6-9673-32640FC547F7@yahoo.com> <20221002182049.GA2255@www.zefox.net>
index | next in thread | previous in thread | raw e-mail
An odd occurrence not seen before, perhaps because
I never waited long enough.
The console reported:
U-Boot 2022.04 (Oct 02 2022 - 09:46:36 -0700)
DRAM: 948 MiB
RPI 3 Model B (0xa02082)
Core: 69 devices, 10 uclasses, devicetree: board
MMC: mmc@7e300000: 2
Loading Environment from FAT... In: serial
Out: vidconsole
Err: vidconsole
Net: No ethernet found.
starting USB...
Bus usb@7e980000: USB DWC2
scanning bus usb@7e980000 for devices... error in inquiry
6 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
MMC Device 0 not found
no mmc device at slot 0
MMC Device 1 not found
no mmc device at slot 1
Card did not respond to voltage select! : -110
Device 0: unknown device
missing environment variable: pxeuuid
Retrieving file: pxelinux.cfg/01-b8-27-eb-ba-68-d5
Retrieving file: pxelinux.cfg/00000000
Retrieving file: pxelinux.cfg/0000000
Retrieving file: pxelinux.cfg/000000
Retrieving file: pxelinux.cfg/00000
Retrieving file: pxelinux.cfg/0000
Retrieving file: pxelinux.cfg/000
Retrieving file: pxelinux.cfg/00
Retrieving file: pxelinux.cfg/0
Retrieving file: pxelinux.cfg/default-arm-bcm283x-rpi
Retrieving file: pxelinux.cfg/default-arm-bcm283x
Retrieving file: pxelinux.cfg/default-arm
Retrieving file: pxelinux.cfg/default
Config file not found
U-Boot> usb reset
resetting USB...
Bus usb@7e980000: USB DWC2
scanning bus usb@7e980000 for devices... 6 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
U-Boot> run bootcmd_usb0
[a few seconds elapsed]
Device 0: [ few minutes] Vendor: SABRENT Rev: 0214 Prod:
Type: Hard Disk
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
... is now current device
[tens of minutes elapsed]
** No partition table - usb 0 **
Couldn't find partition usb 0:1
U-Boot>
U-Boot>
U-Boot>
U-Boot>
U-Boot>
I thought it was stuck, but apparently not.
It's still unbootable.
Not sure it's relevant, but certainly a surprise to me.
bob prohaska
help
Want to link to this message? Use this
URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20221002190614.GA2704>