Date: Mon, 9 Oct 2000 17:11:14 -0400 (EDT) From: Arley Carter <arc@twinds.com> To: Steven Farmer <steve@megahack.com> Cc: freebsd-stable@FreeBSD.ORG Subject: Re: ahc driver problem Message-ID: <Pine.BSF.4.21.0010091651170.30399-200000@seahawk.twinds.com> In-Reply-To: <14815.61540.655647.106686@catbert.megahack.com>
index | next in thread | previous in thread | raw e-mail
[-- Attachment #1 --]
I can report the same failure. My config dmesg is attached to this
message. The ahc driver put on the 4.1 Release CD works and the system
boots and operates with no problems detected. This problem occurs when
the machine is booted from the new GENERIC kernel built from sources
cvsup'd Saturday Oct. 7. Therefore some change committed between these two
dates broke the driver. I have not tried building current. Is this
problem also present in current or only stable?
Cheers:
-arc
Arley Carter arc@twinds.com
Tradewinds Technologies, Inc. www.twinds.com
Winston-Salem, NC USA Network Engineering & Security
[-- Attachment #2 --]
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.1-RELEASE #0: Fri Jul 28 14:30:31 GMT 2000
jkh@ref4.freebsd.org:/usr/src/sys/compile/GENERIC
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (797.42-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x683 Stepping = 3
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,XMM>
real memory = 132907008 (129792K bytes)
avail memory = 125116416 (122184K bytes)
pnpbios: Bad PnP BIOS data checksum
Preloaded elf kernel "kernel.old" at 0xc040d000.
Pentium Pro MTRR support enabled
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82810E (i810E GMCH) Host To Hub bridge> on motherboard
pci0: <PCI bus> on pcib0
pci0: <Intel 82810E (i810E GMCH) SVGA controller> at 1.0 irq 11
pcib1: <Intel 82801AA (ICH) Hub to PCI bridge> at device 30.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <unknown card> (vendor=0x1274, dev=0x1371) at 7.0 irq 11
ahc0: <Adaptec 2940A Ultra SCSI adapter> port 0xd800-0xd8ff mem 0xff8ff000-0xff8fffff irq 11 at device 8.0 on pci1
ahc0: aic7860 Single Channel A, SCSI Id=7, 3/255 SCBs
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xdf00-0xdf3f mem 0xff700000-0xff7fffff,0xff8fe000-0xff8fefff irq 10 at device 9.0 on pci1
fxp0: Ethernet address 00:d0:b7:5d:d9:29
isab0: <Intel 82801AA (ICH) PCI to LPC bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH ATA66 controller> port 0xffa0-0xffaf at device 31.1 on pci0
uhci0: <Intel 82801AA (ICH) USB controller> port 0xef80-0xef9f irq 9 at device 31.2 on pci0
usb0: <Intel 82801AA (ICH) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub0: port 1 power on failed, IOERROR
uhub0: port 2 power on failed, IOERROR
pci0: <unknown card> (vendor=0x8086, dev=0x2413) at 31.3 irq 10
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppi0: <Parallel I/O> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
plip0: <PLIP network interface> on ppbus0
Waiting 15 seconds for SCSI devices to settle
Mounting root from ufs:/dev/da0s1a
da0 at ahc0 bus 0 target 0 lun 0
da0: <SEAGATE ST51080N 0958> Fixed Direct Access SCSI-2 device
da0: 10.000MB/s transfers (10.000MHz, offset 15), Tagged Queueing Enabled
da0: 1030MB (2109840 512 byte sectors: 255H 63S/T 131C)
da3 at ahc0 bus 0 target 5 lun 0
da3: <SEAGATE ST31200N SUN1.05 8722> Fixed Direct Access SCSI-2 device
da3: 10.000MB/s transfers (10.000MHz, offset 15), Tagged Queueing Enabled
da3: 1006MB (2061108 512 byte sectors: 64H 32S/T 1006C)
da2 at ahc0 bus 0 target 3 lun 0
da2: <SEAGATE ST31200N 3138> Fixed Direct Access SCSI-2 device
da2: 10.000MB/s transfers (10.000MHz, offset 15), Tagged Queueing Enabled
da2: 1005MB (2059140 512 byte sectors: 64H 32S/T 1005C)
cd0 at ahc0 bus 0 target 4 lun 0
cd0: <MATSHITA CD-ROM CR-504 ST23> Removable CD-ROM SCSI-2 device
cd0: 5.000MB/s transfers (5.000MHz, offset 15)
cd0: Attempt to query device size failed: NOT READY, Medium not present
da1 at ahc0 bus 0 target 1 lun 0
da1: <CONNER CFP1080S 4649> Fixed Direct Access SCSI-2 device
da1: 10.000MB/s transfers (10.000MHz, offset 15), Tagged Queueing Enabled
da1: 1030MB (2110812 512 byte sectors: 255H 63S/T 131C)
vinum: loaded
(da1:ahc0:0:1:0): SCB 0xb - timed out in Command phase, SEQADDR == 0x155
(da1:ahc0:0:1:0): BDR message in message buffer
(da1:ahc0:0:1:0): no longer in timeout, status = 353
(da1:ahc0:0:1:0): Unexpected busfree in Message-out phase
SEQADDR == 0x155
(da1:ahc0:0:1:0): Synchronize cache failed, status == 0x53, scsi status == 0x0
vinum: reading configuration from /dev/da3s1e
vinum: updating configuration from /dev/da2s1e
vinum: updating configuration from /dev/da1s1e
help
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.4.21.0010091651170.30399-200000>