Date: Fri, 22 Dec 2000 12:44:22 -0500 (EST) From: "H. Jared Agnew" <hjagnew@mba1.mba-consulting.com> To: questions@freebsd.org Subject: dial in question REVISED Message-ID: <200012221744.eBMHiME02381@mba1.mba-consulting.com>
next in thread | raw e-mail | index | archive | help
I'm so sorry to re send this question but I figured it would save maybe
one or two people the time of replying. In the original e-mail I included
the incorrect gettytab and ttys file. Thanks again for any help.
Setup :
FreeBSD -- 4.2 Stable 12/21/00 i386
/dev/ttyd0 -- SB Modem Blaster 56K II
/dev/ttyd1 -- SB Modem Blaster 56K II
/dev/gettytab -- included
/dev/ttys -- included
Problem :
I'm using `ppp` on /dev/cuaa1 (/dev/ttyd1) to dial in to
/dev/ttyd0. ttyd0 picks up and talks with ttyd1, and seems
to establish a connection. ttyd0 tells ttyd1 that it has connected
at what ever speed ttyd1 asks for (ie "CONNECT 9600"). When
I use `watch` to look at what is going on with ttyd0, it shows
the usual login prompt. However on ttyd1 all I see is the "CONNECT"
message and then garbage. When I type anything in `ppp` (ttyd1)
it shows up as garbage on both the `watch` of ttyd0 and in `ppp`
of ttyd1, but it is not the same garbage. The modems are identical
and have identical register settings save for the answer register.
Thanks for any help you might give.
--- /dev/gettytab ---
# $FreeBSD: src/etc/gettytab,v 1.17.2.1 2000/08/16 22:46:30 jhb Exp $
# from: @(#)gettytab 5.14 (Berkeley) 3/27/91
#
# Most of the table entries here are just copies of the old getty table,
# it is by no means certain, or even likely, that any of them are optimal
# for any purpose whatever. Nor is it likely that more than a couple are
# even correct.
#
# The default gettytab entry, used to set defaults for all other
# entries, and in cases where getty is called with no table name.
#
# cb, ce and ck are desirable on most crt's. The non-crt entries need to
# be changed to turn them off (:cb@:ce@:ck@:).
#
# lc should always be on; it's a remainder of some stone age when there
# have been terminals around not being able of handling lower-case
# characters. Those terminals aren't supported any longer, but getty is
# `smart' about them by default.
#
# Parity defaults to even, but the Pc entry and all the `std' entries
# specify no parity. The different parities are:
# (none): same as even except -inpck instead of inpck for login.
# ep: getty will use raw mode (cs8 -parenb) (unless rw is set) and
# fake parity. login will use even parity (cs7 parenb -parodd).
# op: same as ep except odd parity (cs7 parenb parodd) for login.
# op overrides ep.
# ap: same as ep except -inpck instead of inpck for login.
# ap overrides op and ep.
# np: 1. don't fake parity in getty. The fake parity garbles
# characters on non-terminals (like pccons) that don't
# support parity. It would probably better for getty not to
# try to fake parity. It could just use cbreak mode so as
# not to force cs8 and let the hardware handle the parity.
# login has to be rely on the hardware anyway.
# 2. set PASS8, giving cs8 -parenb -istrip -inpck.
# np:ep: same as np except inpck.
# np:op: same as np:ep except for parodd (but parodd is overridden).
# np:ap: same as np except istrip.
#
default:\
:cb:ce:ck:lc:fd#1000:im=\r\n%s/%m (%h) (%t)\r\n\r\n:sp#1200:
#
# Fixed speed entries
#
# The "std.NNN" names are known to the special case
# portselector code in getty, however they can
# be assigned to any table desired.
# The "NNN-baud" names are known to the special case
# autobaud code in getty, and likewise can
# be assigned to any table desired (hopefully the same speed).
#
a|std.110|110-baud:\
:np:nd#1:cd#1:uc:sp#110:
b|std.134|134.5-baud:\
:np:nd#1:cd#2:ff#1:td#1:sp#134:ht:nl:
1|std.150|150-baud:\
:np:nd#1:cd#2:td#1:fd#1:sp#150:ht:nl:lm=\E\72\6\6\17login\72 :
c|std.300|300-baud:\
:np:nd#1:cd#1:sp#300:
d|std.600|600-baud:\
:np:nd#1:cd#1:sp#600:
f|std.1200|1200-baud:\
:np:fd#1:sp#1200:
6|std.2400|2400-baud:\
:np:sp#2400:
7|std.4800|4800-baud:\
:np:sp#4800:
2|std.9600|9600-baud:\
:np:sp#9600:
g|std.19200|19200-baud:\
:np:sp#19200:
std.38400|38400-baud:\
:np:sp#38400:
std.57600|57600-baud:\
:np:sp#57600:
std.115200|115200-baud:\
:np:sp#115200:
std.230400|230400-baud:\
:np:sp#230400:
vha|VH300|High Speed Modem at 300,8-bit:\
:nx=VH230400:tc=std.300:
vhb|VH1200|High Speed Modem at 1200,8-bit:\
:nx=VH300:tc=std.1200:
vhc|VH2400|High Speed Modem at 2400,8-bit:\
:nx=VH1200:tc=std.2400:
vhd|VH9600|High Speed Modem at 9600,8-bit:\
:nx=VH2400:tc=std.9600:
vhe|VH19200|High Speed Modem at 19200,8-bit:\
:nx=VH9600:tc=std.19200:
vhf|VH38400|High Speed Modem at 38400,8-bit:\
:nx=VH19200:tc=std.38400:
vhg|VH57600|High Speed Modem at 57600,8-bit:\
:nx=VH38400:tc=std.57600:
vhh|VH115200|High Speed Modem at 115200,8-bit:\
:nx=VH57600:tc=std.115200:
vhi|VH230400|High Speed Modem at 230400,8-bit:\
:nx=VH230400:tc=std.230400:
#
# Entry specifying explicit device settings. See termios(4) and
# /usr/include/termios.h, too. The entry forces the tty into
# CLOCAL mode (so no DCD is required), and uses Xon/Xoff flow control.
#
# cflags: CLOCAL | HUPCL | CREAD | CS8
# oflags: OPOST | ONLCR | OXTABS
# iflags: IXOFF | IXON | ICRNL | IGNPAR
# lflags: IEXTEN | ICANON | ISIG | ECHOCTL | ECHO | ECHOK | ECHOE | ECHOKE
#
# The `0' flags don't have input enabled. The `1' flags don't echo.
# (Echoing is done inside getty itself.)
#
local.9600|CLOCAL tty @ 9600 Bd:\
:c0#0x0000c300:c1#0x0000cb00:c2#0x0000cb00:\
:o0#0x00000007:o1#0x00000002:o2#0x00000007:\
:i0#0x00000704:i1#0x00000000:i2#0x00000704:\
:l0#0x000005cf:l1#0x00000000:l2#0x000005cf:\
:sp#9600:
#
# Dial in rotary tables, speed selection via 'break'
#
0|d300|Dial-300:\
:nx=d1200:cd#2:sp#300:
d1200|Dial-1200:\
:nx=d150:fd#1:sp#1200:
d150|Dial-150:\
:nx=d110:lm@:tc=150-baud:
d110|Dial-110:\
:nx=d300:tc=300-baud:
#
# Fast dialup terminals, 2400/1200/300 rotary (can start either way)
#
D2400|d2400|Fast-Dial-2400:\
:nx=D1200:tc=2400-baud:
3|D1200|Fast-Dial-1200:\
:nx=D300:tc=1200-baud:
5|D300|Fast-Dial-300:\
:nx=D2400:tc=300-baud:
#
#telebit (19200)
#
t19200:\
:nx=t2400:tc=19200-baud:
t2400:\
:nx=t1200:tc=2400-baud:
t1200:\
:nx=t19200:tc=1200-baud:
#
#telebit (9600)
#
t9600:\
:nx=t2400a:tc=9600-baud:
t2400a:\
:nx=t1200a:tc=2400-baud:
t1200a:\
:nx=t9600:tc=1200-baud:
#
# Odd special case terminals
#
-|tty33|asr33|Pity the poor user of this beast:\
:tc=110-baud:
4|Console|Console Decwriter II:\
:nd@:cd@:rw:tc=300-baud:
e|Console-1200|Console Decwriter III:\
:fd@:nd@:cd@:rw:tc=1200-baud:
i|Interdata console:\
:uc:sp#0:
l|lsi chess terminal:\
:sp#300:
X|Xwindow|X window system:\
:fd@:nd@:cd@:rw:sp#9600:
P|Pc|Pc console:\
:ht:np:sp#115200:
#
# Wierdo special case for fast crt's with hardcopy devices
#
8|T9600|CRT with hardcopy:\
:nx=T300:tc=9600-baud:
9|T300|CRT with hardcopy (300):\
:nx=T9600:tc=300-baud:
#
# Plugboard, and misc other terminals
#
plug-9600|Plugboard-9600:\
:pf#1:tc=9600-baud:
p|P9600|Plugboard-9600-rotary:\
:pf#1:nx=P300:tc=9600-baud:
q|P300|Plugboard-300:\
:pf#1:nx=P1200:tc=300-baud:
r|P1200|Plugboard-1200:\
:pf#1:nx=P9600:tc=1200-baud:
#
# XXXX Port selector
#
s|DSW|Port Selector:\
:ps:sp#2400:
#
# Auto-baud speed detect entry for Micom 600.
# Special code in getty will switch this out
# to one of the NNN-baud entries.
#
A|Auto-baud:\
:ab:sp#2400:f0#040:
#
# autologin - automatically log in as root
#
autologin|al.9600:\
:al=root:tc=std.9600:
#
# $FreeBSD: src/etc/etc.i386/ttys,v 1.8 2000/01/29 12:18:03 obrien Exp $
# @(#)ttys 5.1 (Berkeley) 4/17/89
#
# This file specifies various information about terminals on the system.
# It is used by several different programs. Common entries for the
# various columns include:
#
# name The name of the terminal device.
#
# getty The program to start running on the terminal. Typically a
# getty program, as the name implies. Other common entries
# include none, when no getty is needed, and xdm, to start the
# X Window System.
#
# type The initial terminal type for this port. For hardwired
# terminal lines, this will contain the type of terminal used.
# For virtual consoles, the correct type is cons25. Other
# common values include network for network connections on
# pseudo-terminals, dialup for incoming modem ports, and unknown
# when the terminal type cannot be predetermined.
#
# status Must be on or off. If on, init will run the getty program on
# the specified port. If the word "secure" appears, this tty
# allows root login.
#
# name getty type status comments
#
# If console is marked "insecure", then init will ask for the root password
# when going to single-user mode.
console none unknown off secure
#
ttyv0 "/usr/libexec/getty Pc" cons25 on secure
# Virtual terminals
ttyv1 "/usr/libexec/getty Pc" cons25 on secure
ttyv2 "/usr/libexec/getty Pc" cons25 on secure
ttyv3 "/usr/libexec/getty Pc" cons25 on secure
ttyv4 "/usr/libexec/getty Pc" cons25 on secure
ttyv5 "/usr/libexec/getty Pc" cons25 on secure
ttyv6 "/usr/libexec/getty Pc" cons25 on secure
ttyv7 "/usr/libexec/getty Pc" cons25 on secure
ttyv8 "/usr/X11R6/bin/xdm -nodaemon" xterm off secure
# Serial terminals
# The 'dialup' keyword identifies dialin lines to login, fingerd etc.
ttyd0 "/usr/libexec/getty VH57600" dialup on
#ttyd0 "/usr/libexec/getty std.9600" dialup off secure
ttyd1 "/usr/libexec/getty std.9600" dialup off secure
ttyd2 "/usr/libexec/getty std.9600" dialup off secure
ttyd3 "/usr/libexec/getty std.9600" dialup off secure
# Pseudo terminals
ttyp0 none network
ttyp1 none network
ttyp2 none network
ttyp3 none network
ttyp4 none network
ttyp5 none network
ttyp6 none network
ttyp7 none network
ttyp8 none network
ttyp9 none network
ttypa none network
ttypb none network
ttypc none network
ttypd none network
ttype none network
ttypf none network
ttypg none network
ttyph none network
ttypi none network
ttypj none network
ttypk none network
ttypl none network
ttypm none network
ttypn none network
ttypo none network
ttypp none network
ttypq none network
ttypr none network
ttyps none network
ttypt none network
ttypu none network
ttypv none network
ttyq0 none network
ttyq1 none network
ttyq2 none network
ttyq3 none network
ttyq4 none network
ttyq5 none network
ttyq6 none network
ttyq7 none network
ttyq8 none network
ttyq9 none network
ttyqa none network
ttyqb none network
ttyqc none network
ttyqd none network
ttyqe none network
ttyqf none network
ttyqg none network
ttyqh none network
ttyqi none network
ttyqj none network
ttyqk none network
ttyql none network
ttyqm none network
ttyqn none network
ttyqo none network
ttyqp none network
ttyqq none network
ttyqr none network
ttyqs none network
ttyqt none network
ttyqu none network
ttyqv none network
ttyr0 none network
ttyr1 none network
ttyr2 none network
ttyr3 none network
ttyr4 none network
ttyr5 none network
ttyr6 none network
ttyr7 none network
ttyr8 none network
ttyr9 none network
ttyra none network
ttyrb none network
ttyrc none network
ttyrd none network
ttyre none network
ttyrf none network
ttyrg none network
ttyrh none network
ttyri none network
ttyrj none network
ttyrk none network
ttyrl none network
ttyrm none network
ttyrn none network
ttyro none network
ttyrp none network
ttyrq none network
ttyrr none network
ttyrs none network
ttyrt none network
ttyru none network
ttyrv none network
ttys0 none network
ttys1 none network
ttys2 none network
ttys3 none network
ttys4 none network
ttys5 none network
ttys6 none network
ttys7 none network
ttys8 none network
ttys9 none network
ttysa none network
ttysb none network
ttysc none network
ttysd none network
ttyse none network
ttysf none network
ttysg none network
ttysh none network
ttysi none network
ttysj none network
ttysk none network
ttysl none network
ttysm none network
ttysn none network
ttyso none network
ttysp none network
ttysq none network
ttysr none network
ttyss none network
ttyst none network
ttysu none network
ttysv none network
ttyP0 none network
ttyP1 none network
ttyP2 none network
ttyP3 none network
ttyP4 none network
ttyP5 none network
ttyP6 none network
ttyP7 none network
ttyP8 none network
ttyP9 none network
ttyPa none network
ttyPb none network
ttyPc none network
ttyPd none network
ttyPe none network
ttyPf none network
ttyPg none network
ttyPh none network
ttyPi none network
ttyPj none network
ttyPk none network
ttyPl none network
ttyPm none network
ttyPn none network
ttyPo none network
ttyPp none network
ttyPq none network
ttyPr none network
ttyPs none network
ttyPt none network
ttyPu none network
ttyPv none network
ttyQ0 none network
ttyQ1 none network
ttyQ2 none network
ttyQ3 none network
ttyQ4 none network
ttyQ5 none network
ttyQ6 none network
ttyQ7 none network
ttyQ8 none network
ttyQ9 none network
ttyQa none network
ttyQb none network
ttyQc none network
ttyQd none network
ttyQe none network
ttyQf none network
ttyQg none network
ttyQh none network
ttyQi none network
ttyQj none network
ttyQk none network
ttyQl none network
ttyQm none network
ttyQn none network
ttyQo none network
ttyQp none network
ttyQq none network
ttyQr none network
ttyQs none network
ttyQt none network
ttyQu none network
ttyQv none network
ttyR0 none network
ttyR1 none network
ttyR2 none network
ttyR3 none network
ttyR4 none network
ttyR5 none network
ttyR6 none network
ttyR7 none network
ttyR8 none network
ttyR9 none network
ttyRa none network
ttyRb none network
ttyRc none network
ttyRd none network
ttyRe none network
ttyRf none network
ttyRg none network
ttyRh none network
ttyRi none network
ttyRj none network
ttyRk none network
ttyRl none network
ttyRm none network
ttyRn none network
ttyRo none network
ttyRp none network
ttyRq none network
ttyRr none network
ttyRs none network
ttyRt none network
ttyRu none network
ttyRv none network
ttyS0 none network
ttyS1 none network
ttyS2 none network
ttyS3 none network
ttyS4 none network
ttyS5 none network
ttyS6 none network
ttyS7 none network
ttyS8 none network
ttyS9 none network
ttySa none network
ttySb none network
ttySc none network
ttySd none network
ttySe none network
ttySf none network
ttySg none network
ttySh none network
ttySi none network
ttySj none network
ttySk none network
ttySl none network
ttySm none network
ttySn none network
ttySo none network
ttySp none network
ttySq none network
ttySr none network
ttySs none network
ttySt none network
ttySu none network
ttySv none network
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200012221744.eBMHiME02381>