Date: Mon, 25 May 2009 10:49:39 -0400 From: Nicolas Blais <nicblais@clkroot.net> To: Willem Jan Withagen <wjw@withagen.nl> Cc: freebsd-current@freebsd.org Subject: Re: syslogd starting before IPv6 network is up Message-ID: <7061d9f50905250749n1c152f0fs41f7042ac374da82@mail.gmail.com> In-Reply-To: <4A1858CE.8050803@withagen.nl> References: <7061d9f50905230958n5fd7d434t790a964e79511d6b@mail.gmail.com> <4A1853A7.8080606@digiware.nl> <7061d9f50905231257n29d9e75ehb827ffdc9c077353@mail.gmail.com> <4A1858CE.8050803@withagen.nl>
index | next in thread | previous in thread | raw e-mail
[-- Attachment #1 --]
On Sat, May 23, 2009 at 4:13 PM, Willem Jan Withagen <wjw@withagen.nl>wrote:
> Nicolas Blais wrote:
>
>> On Sat, May 23, 2009 at 3:51 PM, Willem Jan Withagen <wjw@digiware.nl
>> >wrote:
>>
>> Nicolas Blais wrote:
>>>
>>> I migrated one of my 8-CURRENT (Thu May 21) box to IPv6 and since then,
>>>> I
>>>> get the following message at boot:
>>>>
>>>> syslogd: bind: Can't assign requested address
>>>> syslogd: bind: Can't assign requested address
>>>> syslogd:
>>>> child pid 250 exited with return code 1
>>>>
>>>> and syslogd obviously fails to start. Apparently this problem has been
>>>> reported before, but no actual solution other than start syslogd from
>>>> rc.local was given.
>>>>
>>>> It is not because net.inet6.ip6.v6only is off?
>>>
>>> Because than you otherwise get ip4 in ip6 mapping.
>>> It should be of in recent releases, but in 5.x I remember it being on.
>>>
>>
> Perhaps you are right, but that interface requires ip4 to connect to the
>> tunnel broker and become ip6-capable. I don't understand why that sysctl
>> should have an effect on the rcorder. I checked and net.inet6.ip6.v6only:
>> 1
>>
>> Here's my dmesg:
>>
>> /etc/rc: WARNING: failed to start syslogd
>> Starting Network: lo0 em0.
>> May 22 15:59:53 pflogd[620]: [priv]: msg PRIV_OPEN_LOG received
>> pf enabled
>>
> ....
>
>> IPv4 mapped IPv6 address support=NO
>>
>
> Well that should not be the case given what you have.
>
> You could use lsof to see what has the socket open already.
> Or start syslog with strace and see where it fails.
>
> Or first check when booting without firewall
>
> --WjW
>
>
I tried disabling the firewall and it didn't fix the problem.
I have attached a dmesg -a with RC_DEBUG="YES"
Thanks,
Nicolas.
[-- Attachment #2 --]
Copyright (c) 1992-2009 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.0-CURRENT #2: Thu May 21 06:28:12 EDT 2009
root@daemon:/usr/obj/usr/src/sys/OPTIPLEX755
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Core(TM)2 Duo CPU E6750 @ 2.66GHz (2660.00-MHz K8-class CPU)
Origin = "GenuineIntel" Id = 0x6fb Stepping = 11
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0xe3fd<SSE3,DTES64,MON,DS_CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,PDCM>
AMD Features=0x20100800<SYSCALL,NX,LM>
AMD Features2=0x1<LAHF>
TSC: P-state invariant
real memory = 2147483648 (2048 MB)
avail memory = 2024669184 (1930 MB)
ACPI APIC Table: <DELL B9K >
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
FreeBSD/SMP: 1 package(s) x 2 core(s)
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
ioapic0: Changing APIC ID to 8
ioapic0 <Version 2.0> irqs 0-23 on motherboard
lapic0: Forcing LINT1 to edge trigger
kbd1 at kbdmux0
cryptosoft0: <software crypto> on motherboard
acpi0: <DELL B9K > on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 900
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
0:0:1:0 sec 1 sub 1
0:0:28:0 sec 2 sub 2
0:0:30:0 sec 3 sub 3
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0xdc00-0xdcff mem 0xf0000000-0xf7ffffff,0xfe9e0000-0xfe9effff irq 16 at device 0.0 on pci1
vgapci1: <VGA-compatible display> mem 0xfe9f0000-0xfe9fffff at device 0.1 on pci1
pci0: <simple comms> at device 3.0 (no driver attached)
atapci0: <Intel ATA controller> port 0xfe80-0xfe87,0xfe90-0xfe93,0xfea0-0xfea7,0xfeb0-0xfeb3,0xfef0-0xfeff irq 18 at device 3.2 on pci0
atapci0: [ITHREAD]
ata2: <ATA channel 0> on atapci0
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci0
ata3: [ITHREAD]
pci0: <simple comms, UART> at device 3.3 (no driver attached)
em0: <Intel(R) PRO/1000 Network Connection 6.9.9> port 0xecc0-0xecdf mem 0xfebe0000-0xfebfffff,0xfebdb000-0xfebdbfff irq 21 at device 25.0 on pci0
em0: Using MSI interrupt
em0: [FILTER]
em0: Ethernet address: 00:21:9b:34:a2:35
uhci0: <Intel 82801I (ICH9) USB controller> port 0xff20-0xff3f irq 16 at device 26.0 on pci0
uhci0: [ITHREAD]
uhci0: LegSup = 0x0f00
usbus0: <Intel 82801I (ICH9) USB controller> on uhci0
uhci1: <Intel 82801I (ICH9) USB controller> port 0xff00-0xff1f irq 17 at device 26.1 on pci0
uhci1: [ITHREAD]
uhci1: LegSup = 0x0f00
usbus1: <Intel 82801I (ICH9) USB controller> on uhci1
ehci0: <Intel 82801I (ICH9) USB 2.0 controller> mem 0xfebd9c00-0xfebd9fff irq 22 at device 26.7 on pci0
ehci0: [ITHREAD]
usbus2: EHCI version 1.0
usbus2: <Intel 82801I (ICH9) USB 2.0 controller> on ehci0
hdac0: <Intel 82801I High Definition Audio Controller> mem 0xfebdc000-0xfebdffff irq 16 at device 27.0 on pci0
hdac0: HDA Driver Revision: 20090401_0132
hdac0: [ITHREAD]
pcib2: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pci2: <ACPI PCI bus> on pcib2
uhci2: <Intel 82801I (ICH9) USB controller> port 0xff80-0xff9f irq 23 at device 29.0 on pci0
uhci2: [ITHREAD]
uhci2: LegSup = 0x0000
usbus3: <Intel 82801I (ICH9) USB controller> on uhci2
uhci3: <Intel 82801I (ICH9) USB controller> port 0xff60-0xff7f irq 17 at device 29.1 on pci0
uhci3: [ITHREAD]
uhci3: LegSup = 0x0000
usbus4: <Intel 82801I (ICH9) USB controller> on uhci3
uhci4: <Intel 82801I (ICH9) USB controller> port 0xff40-0xff5f irq 18 at device 29.2 on pci0
uhci4: [ITHREAD]
uhci4: LegSup = 0x0000
usbus5: <Intel 82801I (ICH9) USB controller> on uhci4
ehci1: <Intel 82801I (ICH9) USB 2.0 controller> mem 0xff980800-0xff980bff irq 23 at device 29.7 on pci0
ehci1: [ITHREAD]
usbus6: EHCI version 1.0
usbus6: <Intel 82801I (ICH9) USB 2.0 controller> on ehci1
pcib3: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci3: <ACPI PCI bus> on pcib3
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xcc80-0xccff mem 0xfe6fff80-0xfe6fffff irq 18 at device 2.0 on pci3
miibus0: <MII bus> on xl0
ukphy0: <Generic IEEE 802.3u media interface> PHY 24 on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl0: Ethernet address: 00:0a:5e:20:c9:15
xl0: [ITHREAD]
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci1: <Intel ICH9 SATA300 controller> port 0xfe00-0xfe07,0xfe10-0xfe13,0xfe20-0xfe27,0xfe30-0xfe33,0xfec0-0xfedf mem 0xff970000-0xff9707ff irq 18 at device 31.2 on pci0
atapci1: [ITHREAD]
atapci1: AHCI called from vendor specific driver
atapci1: AHCI Version 01.20 controller with 6 ports PM supported
ata4: <ATA channel 0> on atapci1
ata4: [ITHREAD]
ata5: <ATA channel 1> on atapci1
ata5: [ITHREAD]
ata6: <ATA channel 2> on atapci1
ata6: [ITHREAD]
ata7: <ATA channel 3> on atapci1
ata7: [ITHREAD]
ata8: <ATA channel 5> on atapci1
ata8: [ITHREAD]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
atrtc0: <AT realtime clock> port 0x70-0x7f irq 8 on acpi0
fdc0: <floppy drive controller (FDE)> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: [FILTER]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model IntelliMouse, device ID 3
ppc0: <Parallel port> port 0x378-0x37f,0x778-0x77f irq 7 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppc0: [ITHREAD]
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
plip0: [ITHREAD]
lpt0: <Printer> on ppbus0
lpt0: [ITHREAD]
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
uart0: [FILTER]
uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
uart1: [FILTER]
cpu0: <ACPI CPU> on acpi0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 82a082a0600082a
device_attach: est0 attach returned 6
p4tcc0: <CPU Frequency Thermal Control> on cpu0
cpu1: <ACPI CPU> on acpi0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 82a082a0600082a
device_attach: est1 attach returned 6
p4tcc1: <CPU Frequency Thermal Control> on cpu1
orm0: <ISA Option ROMs> at iomem 0xc0000-0xccfff,0xcd000-0xcd7ff,0xcd800-0xcf7ff,0xcf800-0xd1fff,0xd2000-0xd3fff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 1.000 msec
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 480Mbps High Speed USB v2.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 12Mbps Full Speed USB v1.0
usbus5: 12Mbps Full Speed USB v1.0
usbus6: 480Mbps High Speed USB v2.0
ata4-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire
ad8: 76293MB <WDC WD800JD-75MSA3 10.01E04> at ata4-master SATA300
ugen0.1: <Intel> at usbus0
uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <Intel> at usbus2
uhub2: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
ugen3.1: <Intel> at usbus3
uhub3: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
ugen4.1: <Intel> at usbus4
uhub4: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
ugen5.1: <Intel> at usbus5
uhub5: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5
ugen6.1: <Intel> at usbus6
uhub6: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus6
ata5-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=40 wire
acd0: DVDR <Optiarc DVD+/-RW AD-7200S/101A> at ata5-master SATA150
hdac0: HDA Codec #0: Analog Devices AD1984
pcm0: <HDA Analog Devices AD1984 PCM #0 Analog> at cad 0 nid 1 on hdac0
pcm1: <HDA Analog Devices AD1984 PCM #1 Analog> at cad 0 nid 1 on hdac0
lapic1: Forcing LINT1 to edge trigger
SMP: AP CPU #1 Launched!
uhub1: 2 ports with 2 removable, self powered
uhub0: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
uhub5: 2 ports with 2 removable, self powered
uhub4: 2 ports with 2 removable, self powered
GEOM: ad8s1: geometry does not match label (255h,63s != 16h,63s).
GEOM_LABEL: Label for provider ad8s1a is ufsid/4a0d3f3f50eef272.
GEOM_LABEL: Label for provider ad8s1d is ufsid/4a0d3f42592e43d2.
GEOM_LABEL: Label for provider ad8s1e is ufsid/4a0d3f41a9b27c62.
GEOM_LABEL: Label for provider ad8s1f is ufsid/4a0d3f3f091e55af.
GEOM_LABEL: Label for provider ad8s1g is ufsid/4a0d3f41dc0c76f8.
Root mount waiting for: usbus6 usbus2
Root mount waiting for: usbus6 usbus2
uhub2: 6 ports with 6 removable, self powered
uhub6: 6 ports with 6 removable, self powered
Trying to mount root from ufs:/dev/ad8s1a
/etc/rc: DEBUG: run_rc_command: doit: dumpon_start
/etc/rc: DEBUG: checkyesno: ddb_enable is set to NO.
/etc/rc: DEBUG: run_rc_command: doit: initrandom_start
Entropy harvesting:
/etc/rc: DEBUG: checkyesno: harvest_interrupt is set to YES.
interrupts
/etc/rc: DEBUG: checkyesno: harvest_ethernet is set to YES.
ethernet
/etc/rc: DEBUG: checkyesno: harvest_p_to_p is set to YES.
point_to_point
ugen0.2: <Tangtop> at usbus0
ukbd0: <EP1> on usbus0
kbd2 at ukbd0
ums0: <EP2> on usbus0
ums0: 5 buttons and [XYZ] coordinates ID=1
kickstart
.
/etc/rc: DEBUG: run_rc_command: start_precmd: [ -n "$(geli_make_list)" ]
/etc/rc: DEBUG: run_rc_command: start_precmd: find_gbde_devices start
/etc/rc: DEBUG: run_rc_command: doit: gbde_start
/etc/rc: DEBUG: run_rc_command: doit: encswap_attach
/etc/rc: DEBUG: run_rc_command: doit: ccd_start
/etc/rc: DEBUG: run_rc_command: doit: swapon -aq
/etc/rc: DEBUG: run_rc_command: doit: fsck_start
/etc/rc: DEBUG: checkyesno: background_fsck is set to NO.
GEOM_LABEL: Label ufsid/4a0d3f3f50eef272 removed.
/dev/ad8s1a: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/ad8s1a: clean, 13763 free (1219 frags, 1568 blocks, 0.5% fragmentation)
GEOM_LABEL: Label for provider ad8s1a is ufsid/4a0d3f3f50eef272.
GEOM_LABEL: Label ufsid/4a0d3f41dc0c76f8 removed.
/dev/ad8s1g: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/ad8s1g: clean, 238199 free (58743 frags, 22432 blocks, 2.9% fragmentation)
GEOM_LABEL: Label for provider ad8s1g is ufsid/4a0d3f41dc0c76f8.
/etc/rc: DEBUG: run_rc_command: doit: root_start
GEOM_LABEL: Label ufsid/4a0d3f3f50eef272 removed.
/etc/rc: DEBUG: checkyesno: hostid_enable is set to YES.
/etc/rc: DEBUG: run_rc_command: doit: hostid_start
/etc/rc: DEBUG: run_rc_command: start_precmd: [ -n "${_mdconfig_list}" ]
/etc/rc: DEBUG: run_rc_command: doit: mountcritlocal_start
GEOM_LABEL: Label ufsid/4a0d3f41dc0c76f8 removed.
/etc/rc: DEBUG: checkyesno: zfs_enable is set to YES.
This module (opensolaris) contains code covered by the
Common Development and Distribution License (CDDL)
see http://opensolaris.org/os/licensing/opensolaris_license/
WARNING: ZFS is considered to be an experimental feature in FreeBSD.
/etc/rc: DEBUG: run_rc_command: doit: zfs_start
ZFS filesystem version 13
ZFS storage pool version 13
ugen1.2: <Logitech> at usbus1
ums1: <Logitech USB-PS/2 Optical Mouse, class 0/0, rev 2.00/20.00, addr 2> on usbus1
ums1: 3 buttons and [XYZ] coordinates ID=0
/etc/rc: DEBUG: checkyesno: cleanvar_enable is set to YES.
/etc/rc: DEBUG: run_rc_command: start_precmd: cleanvar_prestart
/etc/rc: DEBUG: run_rc_command: doit: cleanvar_start
/etc/rc: DEBUG: run_rc_command: doit: devfs_start
/etc/rc: DEBUG: checkyesno: ipfilter_enable is set to NO.
/etc/rc: DEBUG: run_rc_command: doit: addswap_start
/etc/rc: DEBUG: run_rc_command: doit: auto_linklocal_start
/etc/rc: DEBUG: checkyesno: ipv6_enable is set to YES.
/etc/rc: DEBUG: run_rc_command: doit: sysctl_start
/etc/rc: DEBUG: run_rc_command: doit: hostname_start
/etc/rc: DEBUG: checkyesno: ipmon_enable is set to NO.
/etc/rc: DEBUG: run_rc_command: start_precmd: [ -n "${_mdconfig2_list}" ]
/etc/rc: DEBUG: checkyesno: newsyslog_enable is set to YES.
/etc/rc: DEBUG: run_rc_command: doit: newsyslog_start
/etc/rc: DEBUG: pid file (/var/run/syslog.pid): not readable.
/etc/rc: DEBUG: checkyesno: syslogd_enable is set to YES.
/etc/rc: DEBUG: run_rc_command: start_precmd: syslogd_precmd
/etc/rc: DEBUG: checkyesno: named_enable is set to NO.
/etc/rc: DEBUG: run_rc_command: doit: /usr/sbin/syslogd -s
May 25 02:30:05 syslogd: bind: Can't assign requested address
May 25 02:30:05 syslogd: bind: Can't assign requested address
syslogd:
child pid 271 exited with return code 1
/etc/rc: WARNING: failed to start syslogd
/etc/rc: DEBUG: run_rc_command: start_precmd: savecore_prestart
/etc/rc: DEBUG: No dump device. Quitting.
/etc/rc: DEBUG: run_rc_command: doit: ldconfig_start
/etc/rc: DEBUG: checkyesno: ldconfig_insecure is set to NO.
/etc/rc: DEBUG: run_rc_command: doit: archdep_start
/etc/rc: DEBUG: run_rc_command: doit: abi_start
/etc/rc: DEBUG: checkyesno: sysvipc_enable is set to NO.
/etc/rc: DEBUG: checkyesno: linux_enable is set to NO.
/etc/rc: DEBUG: checkyesno: svr4_enable is set to NO.
/etc/rc: DEBUG: checkyesno: sysvipc_enable is set to NO.
/etc/rc: DEBUG: checkyesno: linux_enable is set to NO.
/etc/rc: DEBUG: checkyesno: svr4_enable is set to NO.
/etc/rc: DEBUG: pid file (/var/run/named/pid): not readable.
/etc/rc: DEBUG: checkyesno: named_enable is set to NO.
/etc/rc: DEBUG: run_rc_command: doit: random_start
/etc/rc: DEBUG: run_rc_command: doit: adjkerntz -i
/etc/rc: DEBUG: checkyesno: atm_enable is set to NO.
/etc/rc: DEBUG: checkyesno: ipnat_enable is set to NO.
/etc/rc: DEBUG: checkyesno: ipfs_enable is set to NO.
/etc/rc: DEBUG: checkyesno: kldxref_enable is set to NO.
/etc/rc: DEBUG: run_rc_command: doit: sppp_start
/etc/rc: DEBUG: run_rc_command: doit: network_start
/etc/rc: DEBUG: Cloned:
/etc/rc: DEBUG: checkyesno: synchronous_dhclient is set to NO.
Starting Network: lo0 em0.
/etc/rc: DEBUG: The following interfaces were not configured: xl0 plip0 pflog0 pfsync0
/etc/rc.d/ipfilter: DEBUG: checkyesno: ipfilter_enable is set to NO.
/etc/rc: DEBUG: checkyesno: ppp_enable is set to NO.
/etc/rc: DEBUG: checkyesno: firewall_enable is set to NO.
/etc/rc: DEBUG: run_rc_command: doit: nsswitch_start
/etc/rc: DEBUG: checkyesno: mroute6d_enable is set to NO.
/etc/rc: DEBUG: checkyesno: ipv6_router_enable is set to NO.
/etc/rc: DEBUG: checkyesno: atm_enable is set to NO.
/etc/rc: DEBUG: checkyesno: pfsync_enable is set to NO.
/etc/rc: DEBUG: pid file (/var/run/pflogd.pid): not readable.
/etc/rc: DEBUG: checkyesno: pflog_enable is set to YES.
/etc/rc: DEBUG: run_rc_command: start_precmd: pflog_prestart
/etc/rc: DEBUG: load_kld: pflog kernel module already loaded.
/etc/rc: DEBUG: run_rc_command: doit: /sbin/pflogd -f /var/log/pflog
/etc/rc: DEBUG: checkyesno: pf_enable is set to YES.
May 25 06:30:06 pflogd[679]: [priv]: msg PRIV_OPEN_LOG received
/etc/rc: DEBUG: load_kld: pf kernel module already loaded.
/etc/rc: DEBUG: run_rc_command: doit: pf_start
pf enabled
/etc/rc: DEBUG: run_rc_command: doit: routing_start
/etc/rc: DEBUG: pid file (/var/run/mrouted.pid): not readable.
/etc/rc: DEBUG: checkyesno: mrouted_enable is set to NO.
/etc/rc: DEBUG: checkyesno: router_enable is set to NO.
/etc/rc: DEBUG: run_rc_command: doit: defaultroute_start
/etc/rc: DEBUG: checkyesno: freenet6_enable is set to YES.
/etc/rc: DEBUG: run_rc_command: doit: /usr/local/bin/gw6c -f /usr/local/etc/gw6c.conf
Gateway6 Client v5.1-RELEASE build May 19 2009-11:35:44
Built on ///FreeBSD daemon.videotron.ca 8.0-CURRENT FreeBSD 8.0-CURRENT #1: Tue May 19 11:05:57 EDT 2009 root@daemon.videotron.ca:/usr/obj/usr/src/sys/GENERIC amd64///
Failed to connect to Gateway6 authenticated.freenet6.net. Verify Gateway6 name/address.
Disconnected. Retrying.
Failed to connect to Gateway6 authenticated.freenet6.net. Verify Gateway6 name/address.
Disconnected. Retrying in 30 seconds.
Script /usr/local/etc/rc.d/freenet6 interrupted
/etc/rc: DEBUG: checkyesno: ip6addrctl_enable is set to YES.
/etc/rc: DEBUG: run_rc_command: doit: ip6addrctl_start
/etc/rc: DEBUG: checkyesno: ipv6_enable is set to YES.
/etc/rc: DEBUG: checkyesno: ip6addrctl_verbose is set to NO.
/etc/rc: DEBUG: checkyesno: ipv6_firewall_enable is set to NO.
/etc/rc: DEBUG: checkyesno: ipv6_enable is set to YES.
/etc/rc: DEBUG: run_rc_command: doit: network_ipv6_start
add net ::ffff:0.0.0.0: gateway ::1
add net ::0.0.0.0: gateway ::1
/etc/rc: DEBUG: checkyesno: ipv6_gateway_enable is set to YES.
net.inet6.ip6.forwarding:
0
->
1
net.inet6.ip6.accept_rtadv:
0
->
0
em0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=19b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4>
inet6 fe80::221:9bff:fe34:a235%em0 prefixlen 64 scopeid 0x1
xl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=9<RXCSUM,VLAN_MTU>
inet6 fe80::20a:5eff:fe20:c915%xl0 prefixlen 64 scopeid 0x2
plip0: flags=8851<UP,POINTOPOINT,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
pflog0: flags=141<UP,RUNNING,PROMISC> metric 0 mtu 33152
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
options=3<RXCSUM,TXCSUM>
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5
pfsync0: flags=41<UP,RUNNING> metric 0 mtu 1460
/etc/rc: DEBUG: checkyesno: ipv6_gateway_enable is set to YES.
add net fe80::: gateway ::1
add net ff02::: gateway ::1
/etc/rc: DEBUG: checkyesno: ipv6_ipv4mapping is set to NO.
IPv4 mapped IPv6 address support=NO
/etc/rc: DEBUG: checkyesno: devd_enable is set to YES.
/etc/rc: DEBUG: run_rc_command: doit: /sbin/devd
/etc/pccard_ether: DEBUG: run_rc_command: start_precmd: checkauto
/etc/pccard_ether: DEBUG: run_rc_command: doit: pccard_ether_start
/etc/pccard_ether: DEBUG: run_rc_command: start_precmd: checkauto
/etc/pccard_ether: DEBUG: run_rc_command: doit: pccard_ether_start
/etc/pccard_ether: DEBUG: run_rc_command: start_precmd: checkauto
/etc/pccard_ether: DEBUG: run_rc_command: doit: pccard_ether_start
/etc/pccard_ether: DEBUG: run_rc_command: start_precmd: checkauto
/etc/pccard_ether: DEBUG: run_rc_command: doit: pccard_ether_start
/etc/pccard_ether: DEBUG: run_rc_command: start_precmd: checkauto
/etc/pccard_ether: DEBUG: run_rc_command: doit: pccard_ether_start
/etc/pccard_ether: DEBUG: run_rc_command: start_precmd: checkauto
/etc/pccard_ether: DEBUG: run_rc_command: doit: pccard_ether_start
/etc/rc.d/syscons: DEBUG: run_rc_command: doit: syscons_setkeyboard /dev/ukbd0
Configuring keyboard:
keymap
.
/etc/rc.d/moused: DEBUG: pid file (/var/run/moused.ums0.pid): not readable.
/etc/rc.d/moused: DEBUG: checkyesno: moused_ums0_enable is set to YES.
/etc/rc.d/moused: DEBUG: run_rc_command: doit: moused_start ums0
/etc/rc.d/moused: DEBUG: pid file (/var/run/moused.ums1.pid): not readable.
/etc/rc.d/moused: DEBUG: checkyesno: moused_ums1_enable is set to YES.
/etc/rc.d/moused: DEBUG: run_rc_command: doit: moused_start ums1
/etc/rc.d/dhclient: DEBUG: run_rc_command: doit: dhclient_start
/etc/rc.d/dhclient: DEBUG: checkyesno: background_dhclient is set to NO.
DHCPREQUEST on em0 to 255.255.255.255 port 67
DHCPACK from 192.168.15.1
bound to 192.168.15.58 -- renewal in 1800 seconds.
/etc/rc: DEBUG: checkyesno: devd_enable is set to YES.
/etc/rc: DEBUG: checkyesno: ipsec_enable is set to NO.
/etc/rc: DEBUG: run_rc_command: start_precmd: mountcritremote_precmd
/etc/rc: DEBUG: run_rc_command: doit: mountcritremote_start
/etc/rc.d/cleanvar: DEBUG: checkyesno: cleanvar_enable is set to YES.
/etc/rc.d/cleanvar: DEBUG: run_rc_command: doit: cleanvar_start
/etc/rc: DEBUG: checkyesno: accounting_enable is set to NO.
/etc/rc: DEBUG: checkyesno: ntpdate_enable is set to YES.
/etc/rc: DEBUG: run_rc_command: doit: ntpdate_start
Setting date via ntp.
25 May 06:30:17 ntpdate[1201]: adjust time server 64.6.144.6 offset -0.421032 sec
/etc/rc: DEBUG: checkyesno: rpcbind_enable is set to NO.
/etc/rc: DEBUG: checkyesno: nfs_client_enable is set to NO.
/etc/rc: DEBUG: run_rc_command: doit: nisdomain_start
/etc/rc: DEBUG: checkyesno: nis_server_enable is set to NO.
/etc/rc: DEBUG: checkyesno: nis_client_enable is set to NO.
/etc/rc: DEBUG: checkyesno: amd_enable is set to NO.
/etc/rc: DEBUG: checkyesno: atm_enable is set to NO.
/etc/rc: DEBUG: checkyesno: auditd_enable is set to NO.
/etc/rc: DEBUG: run_rc_command: doit: cleartmp_start
/etc/rc: DEBUG: checkyesno: clear_tmp_enable is set to YES.
/etc/rc: DEBUG: checkyesno: clear_tmp_X is set to YES.
/etc/rc: DEBUG: checkyesno: dmesg_enable is set to YES.
/etc/rc: DEBUG: run_rc_command: doit: do_dmesg
/etc/rc: DEBUG: checkyesno: ipxrouted_enable is set to NO.
/etc/rc: DEBUG: checkyesno: kerberos5_server_enable is set to NO.
/etc/rc: DEBUG: checkyesno: kadmind5_server_enable is set to NO.
/etc/rc: DEBUG: checkyesno: keyserv_enable is set to NO.
/etc/rc: DEBUG: checkyesno: kpasswdd_server_enable is set to NO.
/etc/rc: DEBUG: checkyesno: gssd_enable is set to NO.
/etc/rc: DEBUG: checkyesno: quota_enable is set to NO.
/etc/rc: DEBUG: checkyesno: nfs_server_enable is set to NO.
/etc/rc: DEBUG: pid file (/var/run/mountd.pid): not readable.
/etc/rc: DEBUG: checkyesno: mountd_enable is set to NO.
/etc/rc: DEBUG: checkyesno: nfs_server_enable is set to NO.
/etc/rc: DEBUG: checkyesno: rpc_statd_enable is set to NO.
/etc/rc: DEBUG: checkyesno: rpc_lockd_enable is set to NO.
/etc/rc: DEBUG: checkyesno: pppoed_enable is set to NO.
/etc/rc: DEBUG: run_rc_command: doit: pwcheck_start
/etc/rc: DEBUG: checkyesno: virecover_enable is set to YES.
/etc/rc: DEBUG: run_rc_command: doit: virecover_start
/etc/rc: DEBUG: checkyesno: apm_enable is set to NO.
/etc/rc: DEBUG: checkyesno: apmd_enable is set to NO.
/etc/rc: DEBUG: checkyesno: bootparamd_enable is set to NO.
/etc/rc: DEBUG: pid file (/var/run/hcsecd.pid): not readable.
/etc/rc: DEBUG: checkyesno: hcsecd_enable is set to NO.
/etc/rc: DEBUG: pid file (/var/run/bthidd.pid): not readable.
/etc/rc: DEBUG: checkyesno: bthidd_enable is set to NO.
/etc/rc: DEBUG: run_rc_command: doit: local_start
Starting local daemons:
.
/etc/rc: DEBUG: checkyesno: lpd_enable is set to NO.
/etc/rc: DEBUG: checkyesno: update_motd is set to YES.
/etc/rc: DEBUG: run_rc_command: doit: motd_start
/etc/rc: DEBUG: run_rc_command: doit: mountlate_start
/etc/rc: DEBUG: checkyesno: nscd_enable is set to NO.
/etc/rc: DEBUG: pid file (/var/run/ntpd.pid): not readable.
/etc/rc: DEBUG: checkyesno: ntpd_enable is set to NO.
/etc/rc: DEBUG: checkyesno: powerd_enable is set to NO.
/etc/rc: DEBUG: pid file (/var/run/rarpd.pid): not readable.
/etc/rc: DEBUG: checkyesno: rarpd_enable is set to NO.
/etc/rc: DEBUG: checkyesno: sdpd_enable is set to NO.
/etc/rc: DEBUG: checkyesno: rfcomm_pppd_server_enable is set to NO.
/etc/rc: DEBUG: checkyesno: rtadvd_enable is set to YES.
/etc/rc: DEBUG: run_rc_command: start_precmd: rtadvd_precmd
/etc/rc: DEBUG: checkyesno: ipv6_gateway_enable is set to YES.
/etc/rc: DEBUG: run_rc_command: doit: /usr/sbin/rtadvd em0
/etc/rc: DEBUG: checkyesno: rwhod_enable is set to NO.
/etc/rc: DEBUG: checkyesno: timed_enable is set to NO.
/etc/rc: DEBUG: checkyesno: ugidfw_enable is set to NO.
/etc/rc: DEBUG: checkyesno: nis_yppasswdd_enable is set to NO.
/etc/rc: DEBUG: checkyesno: webmin_enable is set to YES.
/etc/rc: DEBUG: run_rc_command: doit: /usr/local/etc/webmin/start
Pre-loaded WebminCore
/etc/rc: DEBUG: pid file (/var/db/mysql/daemon.pid): not readable.
/etc/rc: DEBUG: checkyesno: mysql_enable is set to YES.
/etc/rc: DEBUG: run_rc_command: start_precmd: mysql_prestart
/etc/rc: DEBUG: checkyesno: mysql_limits is set to NO.
/etc/rc: DEBUG: run_rc_command: doit: su -m mysql -c 'sh -c "/usr/local/bin/mysqld_safe --defaults-extra-file=/var/db/mysql/my.cnf --user=mysql --datadir=/var/db/mysql --pid-file=/var/db/mysql/daemon.pid > /dev/null 2>&1 &"'
/etc/rc: DEBUG: run_rc_command: start_postcmd: mysql_poststart
/etc/rc: DEBUG: checkyesno: htcacheclean_enable is set to NO.
/etc/rc: DEBUG: checkyesno: apache22_http_accept_enable is set to NO.
/etc/rc: DEBUG: pid file (/var/run/httpd.pid): not readable.
/etc/rc: DEBUG: checkyesno: apache22_enable is set to YES.
/etc/rc: DEBUG: run_rc_command: start_precmd: apache22_prestart
Performing sanity check on apache22 configuration:
Syntax OK
/etc/rc: DEBUG: checkyesno: apache22limits_enable is set to NO.
/etc/rc: DEBUG: run_rc_command: doit: /usr/local/sbin/httpd -DNOHTTPACCEPT
/etc/rc: DEBUG: checkyesno: nis_ypxfrd_enable is set to NO.
/etc/rc: DEBUG: checkyesno: rpc_ypupdated_enable is set to NO.
/etc/rc: DEBUG: checkyesno: nis_ypset_enable is set to NO.
/etc/rc: DEBUG: pid file (/var/run/watchdogd.pid): not readable.
/etc/rc: DEBUG: checkyesno: watchdogd_enable is set to NO.
/etc/rc: DEBUG: run_rc_command: start_precmd: syscons_precmd
/etc/rc: DEBUG: run_rc_command: doit: syscons_start
Configuring syscons:
keymap
blanktime
.
/etc/rc: DEBUG: pid file (/var/run/sshd.pid): not readable.
/etc/rc: DEBUG: checkyesno: sshd_enable is set to YES.
/etc/rc: DEBUG: run_rc_command: start_precmd: sshd_precmd
/etc/rc: DEBUG: run_rc_command: doit: /usr/sbin/sshd
/etc/rc: DEBUG: checkyesno: sendmail_enable is set to NO.
/etc/rc: DEBUG: checkyesno: sendmail_submit_enable is set to YES.
/etc/rc: DEBUG: pid file (/var/run/sendmail.pid): not readable.
/etc/rc: DEBUG: checkyesno: sendmail_enable is set to NO.
/etc/rc: DEBUG: checkyesno: sendmail_submit_enable is set to YES.
/etc/rc: DEBUG: pid file (/var/run/sendmail.pid): not readable.
/etc/rc: DEBUG: checkyesno: sendmail_submit_enable is set to YES.
/etc/rc: DEBUG: run_rc_command: start_precmd: sendmail_precmd
/etc/rc: DEBUG: checkyesno: sendmail_submit_enable is set to YES.
/etc/rc: DEBUG: checkyesno: sendmail_rebuild_aliases is set to NO.
/etc/rc: DEBUG: run_rc_command: doit: /usr/sbin/sendmail -L sm-mta -bd -q30m -ODaemonPortOptions=Addr=localhost
/etc/rc: DEBUG: checkyesno: sendmail_outbound_enable is set to NO.
/etc/rc: DEBUG: pid file (/var/spool/clientmqueue/sm-client.pid): not readable.
/etc/rc: DEBUG: checkyesno: sendmail_msp_queue_enable is set to YES.
/etc/rc: DEBUG: run_rc_command: start_precmd: sendmail_precmd
/etc/rc: DEBUG: checkyesno: sendmail_msp_queue_enable is set to YES.
/etc/rc: DEBUG: checkyesno: sendmail_rebuild_aliases is set to NO.
/etc/rc: DEBUG: run_rc_command: doit: /usr/sbin/sendmail -L sm-msp-queue -Ac -q30m
/etc/rc: DEBUG: checkyesno: cron_dst is set to YES.
/etc/rc: DEBUG: pid file (/var/run/cron.pid): not readable.
/etc/rc: DEBUG: checkyesno: cron_enable is set to YES.
/etc/rc: DEBUG: run_rc_command: doit: /usr/sbin/cron -s
/etc/rc: DEBUG: checkyesno: jail_enable is set to NO.
/etc/rc: DEBUG: run_rc_command: doit: pkg_start
/etc/rc.d/sysctl: DEBUG: run_rc_command: doit: sysctl_start last
/etc/rc: DEBUG: checkyesno: kern_securelevel_enable is set to NO.
/etc/rc: DEBUG: pid file (/var/run/moused.pid): not readable.
/etc/rc: DEBUG: checkyesno: moused_enable is set to NO.
/etc/rc: DEBUG: checkyesno: mixer_enable is set to YES.
/etc/rc: DEBUG: run_rc_command: doit: mixer_start
/etc/rc: DEBUG: pid file (/var/run/inetd.pid): not readable.
/etc/rc: DEBUG: checkyesno: inetd_enable is set to NO.
/etc/rc: DEBUG: checkyesno: idmapd_enable is set to NO.
/etc/rc: DEBUG: pid file (/var/run/hostapd.pid): not readable.
/etc/rc: DEBUG: checkyesno: hostapd_enable is set to NO.
/etc/rc: DEBUG: run_rc_command: doit: geli2_start
/etc/rc: DEBUG: pid file (/var/run/ftpd.pid): not readable.
/etc/rc: DEBUG: checkyesno: ftpd_enable is set to NO.
/etc/rc: DEBUG: checkyesno: ftpproxy_enable is set to NO.
/etc/rc: DEBUG: pid file (/var/run/snmpd.pid): not readable.
/etc/rc: DEBUG: checkyesno: bsnmpd_enable is set to NO.
/etc/rc: DEBUG: run_rc_command: doit: bridge_start
/etc/rc: DEBUG: checkyesno: background_fsck is set to NO.
Mon May 25 06:30:23 EDT 2009
help
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?7061d9f50905250749n1c152f0fs41f7042ac374da82>