Date: Fri, 05 Mar 2004 11:23:36 -0800 From: othermark <atkin901@yahoo.com> To: freebsd-current@freebsd.org Subject: Re: [solved!] usb mouse is stuttering and losing input. Message-ID: <c2ak3o$o9m$1@sea.gmane.org> References: <c22tn2$va3$1@sea.gmane.org>
next in thread | previous in thread | raw e-mail | index | archive | help
othermark wrote: > I was wondering if anyone else had seen this problem. I've cvsupped > current from March 1st and have just gotten to the point in building this > machine > up that I can run X11. However, the usb mouse I have is unusable. It's > behaving like ums is not retrieving/receiving all the input. > > Basically you'll move the mouse and nothing will happen and you'll keep > moving it and eventually the pointer will move a little bit, but only in > brief flashes. replying to myself, I know. After some good research, I tried the following: - removing SMP from kernel config .. no effect - adding NO_MIXED_MODE to kernel config .. caused my HDD not to mount on bootup. - removing 'device apic' from kernel config .. success! Of course, this is an SMP capable board, I'd have to use ps/2 if I added a second processor. > The behavior occurs under all these scenarios: > > - I tried a completely different usb mouse > - I tried changing the scheduler ULE to 4BSD > - I tried setting hint.acpi.0.disabled="1" > - I tried turning the ps/2 detection on and off in the bios > - I tried both X and sysmouse support > > No errors from boot time or kernel from this device. > > If I plug the ps/2 to usb adaptor for this mouse and reboot, everythings' > fine. This machine used to run -stable before I upgraded and the USB > mouse worked great. Is anyone else seeing this behavior with usb mice on > -current? > > if I boot it as ps/2, with acpi I get this: > > ohci0: <OHCI (generic) USB controller> mem 0xfeafe000-0xfeafefff irq 16 at > device 15.2 on pci0 > usb0: OHCI version 1.0, legacy support > usb0: <OHCI (generic) USB controller> on ohci0 > usb0: USB revision 1.0 > uhub0: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 4 ports with 4 removable, self powered > > If I boot with the usb mouse and acpi disabled, I get this: > > ohci0: <OHCI (generic) USB controller> mem 0xfeafe000-0xfeafefff irq 12 at > device 15.2 on pci0 > usb0: OHCI version 1.0, legacy support > usb0: <OHCI (generic) USB controller> on ohci0 > usb0: USB revision 1.0 > uhub0: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 4 ports with 4 removable, self powered > ums0: Kensington Kensington USB/PS2 Trackball, rev 1.10/1.00, addr 2, > iclass 3/1 > ums0: 5 buttons and Z dir. > > --- > othermark > atkin901 at nospam dot yahoo dot com > (!wired)?(coffee++):(wired); > > _______________________________________________ > freebsd-current@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-current > To unsubscribe, send any mail to "freebsd-current-unsubscribe@freebsd.org" -- othermark atkin901 at nospam dot yahoo dot com (!wired)?(coffee++):(wired);
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?c2ak3o$o9m$1>