Date: Tue, 7 Nov 2006 18:20:03 +0300 From: "Eugene M. Minkovskii" <emin@mccme.ru> To: freebsd-acpi@freebsd.org Subject: HP Compaq nc6320 ES479EA Message-ID: <20061107152003.GA11335@mccme.ru>
next in thread | raw e-mail | index | archive | help
Hello!
Now I bying laptop HP Compaq nc6320 ES479EA. I install FreeBSD
CURRENT 7.0 on it. I see some bugs in ACPI on this laptop:
1) My kernel permanently generated messages like:
acpi_tz0: _CRT value is absurd, ignored (256.0C)
2) When I boot whithount plugging to power in variable
hw.acpi.battery.time placed absurd value (about 2000 minutes 33
hours!) So I used two batterys simultaneously (primary and
secondary) but this of course wrong value - 2000 min :).
If I boot with plugged power and detach power after the boot
variable hw.acpi.battery.time show good forecast. Again, when I
my secondary battery decharged, variable hw.acpi.battery.time
began to show good forecast.
I would be happy to help FreeBSD community any test on this
laptop model.
following is my dmesg:
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.0-CURRENT #4: Thu Nov 2 14:00:09 MSK 2006
root@hp.house.hcn-strela.ru:/usr/obj/usr/src/sys/GENERIC
WARNING: WITNESS option enabled, expect reduced performance.
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Genuine Intel(R) CPU T2400 @ 1.83GHz (1828.77-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x6e8 Stepping = 8
Features=0xbfe9fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0xc1a9<SSE3,MON,VMX,EST,TM2,XTPR,<b15>>
AMD Features=0x100000<NX>
Cores per package: 2
real memory = 1065156608 (1015 MB)
avail memory = 1028853760 (981 MB)
ACPI APIC Table: <HP 30AA >
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
ioapic0: Changing APIC ID to 1
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
acpi0: <HP 30AA> on motherboard
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi_bus_number: can't get _ADR
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
acpi_ec0: <Embedded Controller: GPE 0x16> port 0x62,0x66 on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
cpu1: <ACPI CPU> on acpi0
acpi_throttle1: <ACPI CPU Throttling> on cpu1
acpi_throttle1: failed to attach P_CNT
device_attach: acpi_throttle1 attach returned 6
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
vgapci0: <VGA-compatible display> port 0x6000-0x6007 mem 0xe8400000-0xe847ffff,0xd0000000-0xdfffffff,0xe8480000-0xe84bffff irq 16 at device 2.0 on pci0
agp0: <Intel 82945GM (945GM GMCH) SVGA controller> on vgapci0
agp0: detected 7932k stolen memory
agp0: aperture size is 256M
vgapci1: <VGA-compatible display> mem 0xe8500000-0xe857ffff at device 2.1 on pci0
pcm0: <Intel 82801G High Definition Audio Controller> mem 0xe8580000-0xe8583fff irq 21 at device 27.0 on pci0
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pci8: <ACPI PCI bus> on pcib1
pci8: <network> at device 0.0 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> irq 18 at device 28.2 on pci0
pci24: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> irq 19 at device 28.3 on pci0
pci32: <ACPI PCI bus> on pcib3
uhci0: <UHCI (generic) USB controller> port 0x6020-0x603f irq 20 at device 29.0 on pci0
uhci0: [GIANT-LOCKED]
usb0: <UHCI (generic) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 2 ports with 2 removable, self powered
uhci1: <UHCI (generic) USB controller> port 0x6040-0x605f irq 21 at device 29.1 on pci0
uhci1: [GIANT-LOCKED]
usb1: <UHCI (generic) USB controller> on uhci1
usb1: USB revision 1.0
uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 2 ports with 2 removable, self powered
uhci2: <UHCI (generic) USB controller> port 0x6060-0x607f irq 18 at device 29.2 on pci0
uhci2: [GIANT-LOCKED]
usb2: <UHCI (generic) USB controller> on uhci2
usb2: USB revision 1.0
uhub2: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2
uhub2: 2 ports with 2 removable, self powered
uhci3: <UHCI (generic) USB controller> port 0x6080-0x609f irq 19 at device 29.3 on pci0
uhci3: [GIANT-LOCKED]
usb3: <UHCI (generic) USB controller> on uhci3
usb3: USB revision 1.0
uhub3: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb3
uhub3: 2 ports with 2 removable, self powered
ehci0: <Intel 82801GB/R (ICH7) USB 2.0 controller> mem 0xe8584000-0xe85843ff irq 20 at device 29.7 on pci0
ehci0: [GIANT-LOCKED]
usb4: EHCI version 1.0
usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
usb4: <Intel 82801GB/R (ICH7) USB 2.0 controller> on ehci0
usb4: USB revision 2.0
uhub4: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb4
uhub4: 8 ports with 8 removable, self powered
uhub5: <vendor 0x0424 product 0x2503, class 9/0, rev 2.00/0.01, addr 2> on uhub4
uhub5: multiple transaction translators
uhub5: 3 ports with 0 removable, self powered
ugen0: <vendor 0x08ff Fingerprint Sensor, class 255/255, rev 1.10/6.21, addr 3> on uhub5
pcib4: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci2: <ACPI PCI bus> on pcib4
pci2:14:0: bad VPD cksum, remain 14
cbb0: <PCI-CardBus Bridge> mem 0xe8100000-0xe8100fff irq 18 at device 6.0 on pci2
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
fwohci0: <1394 Open Host Controller Interface> mem 0xe8101000-0xe81017ff,0xe8104000-0xe8107fff irq 19 at device 6.1 on pci2
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:02:3f:99:29:15:33:0c
fwohci0: Phy 1394a available S400, 3 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:02:3f:15:33:0c
fwe0: Ethernet address: 02:02:3f:15:33:0c
fwe0: if_start running deferred for Giant
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc800ffc0, gen=2, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
fwohci0: phy int
pci2: <mass storage> at device 6.2 (no driver attached)
pci2: <base peripheral> at device 6.3 (no driver attached)
bge0: <Broadcom BCM5705 A3, ASIC rev. 0x3003> mem 0xe8110000-0xe811ffff irq 16 at device 14.0 on pci2
miibus0: <MII bus> on bge0
brgphy0: <BCM5705 10/100/1000baseTX PHY> on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto
bge0: Ethernet address: 00:17:08:2f:a6:90
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH7 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x60a0-0x60af irq 16 at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
atapci1: <Intel ICH7M SATA300 controller> port 0x13f0-0x13f7,0x15f4-0x15f7,0x1370-0x1377,0x1574-0x1577,0x60d0-0x60df mem 0xe8585000-0xe85853ff irq 17 at device 31.2 on pci0
atapci1: AHCI Version 01.10 controller with 4 ports detected
ata2: <ATA channel 0> on atapci1
ata3: <ATA channel 1> on atapci1
ata4: <ATA channel 2> on atapci1
ata5: <ATA channel 3> on atapci1
battery0: <ACPI Control Method Battery> on acpi0
battery1: <ACPI Control Method Battery> on acpi0
acpi_acad0: <AC Adapter> on acpi0
acpi_button0: <Sleep Button> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
acpi_tz0: _CRT value is absurd, ignored (256.0C)
acpi_tz1: <Thermal Zone> on acpi0
acpi_tz2: <Thermal Zone> on acpi0
acpi_tz3: <Thermal Zone> on acpi0
acpi_tz4: <Thermal Zone> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model IntelliMouse, device ID 3
sio0: <Standard PC COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
sio0: [FAST]
pmtimer0 on isa0
orm0: <ISA Option ROM> at iomem 0xc0000-0xcffff pnpid ORM0000 on isa0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ppc0: [GIANT-LOCKED]
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 1.000 msec
acd0: DVDR <MATSHITADVD-RAM UJ-840S/1.11> at ata0-master PIO4
acpi_tz0: _CRT value is absurd, ignored (256.0C)
ad4: 95396MB <HTS541010G9SA00 MBZOC60P> at ata2-master SATA150
pcm0: <HDA Codec: Analog Device AD1981HD>
pcm0: <HDA Driver Revision: 20061017_0033>
SMP: AP CPU #1 Launched!
Trying to mount root from ufs:/dev/ad4s2a
bge0: link state changed to UP
acpi_tz0: _CRT value is absurd, ignored (256.0C)
acpi_tz0: _CRT value is absurd, ignored (256.0C)
acpi_tz0: _CRT value is absurd, ignored (256.0C)
acpi_tz0: _CRT value is absurd, ignored (256.0C)
...<skiped>...
battery1: critically low charge!
--
Sensory yours, Eugene Minkovskii
Сенсорно ваш, Евгений Миньковский
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20061107152003.GA11335>