Date: Mon, 26 Nov 2012 02:41:30 +0000 (UTC) From: Pyun YongHyeon <yongari@FreeBSD.org> To: src-committers@freebsd.org, svn-src-all@freebsd.org, svn-src-stable@freebsd.org, svn-src-stable-9@freebsd.org Subject: svn commit: r243538 - stable/9/sys/dev/bge Message-ID: <201211260241.qAQ2fU7w074744@svn.freebsd.org>
next in thread | raw e-mail | index | archive | help
Author: yongari Date: Mon Nov 26 02:41:30 2012 New Revision: 243538 URL: http://svnweb.freebsd.org/changeset/base/243538 Log: MFC r241388-241393: r241388: If the maximum payload size is 256 bytes or more, set the DMA write water mark to 256 bytes. Otherwise controller will encounter DMA write under run errors and would result in RX DMA hang. If the maximum payload size is 128 bytes, the water mark is set to 128 bytes as usual. While here, set maximum read request size to 2048 for BCM5719/BCM5720. For other PCIe devices, use 4096. And reprogram the maximum read request size whenever device reset is performed. r241389: On PHY write error use hex number to show the value. Add more comments. r241390: Honor PHY type fiber for BCM5717/BCM5718/BCM5719/BCM5720. r241391: Do not force PCIe 1.0a mode in device reset on BCM5717 and newer controllers. BCM5785 does not require PCI 1.0a mode as well during reset. r241392: Fix a long standing VCPU reset sequence bug on BCM5906. The VCPU(Virtual CPU) of BCM5906 is used to provide a mechanism to control the bootcode execution and to pick up configuration data stored inside the EEPROM. The bootcode of BCM5906 will check the BGE_VCPU_STATUS_DRV_RESET bit to decide which booting procedure to choose. Data sheet indicates the VCPU of BCM5906 should set BGE_VCPU_STATUS_DRV_RESET bit *before* VCPU reset or global reset. r241393: Remove unnecessary delay. I don't see any comments in data sheet that requires 10ms delay after device reset. Because that code was there from day 1, I guess it was added to give enough settlement time after updating BGE_MAC_MODE register. The recommended delay time for BGE_MAC_MODE after updating is 40us and it was already done in r241219. Modified: stable/9/sys/dev/bge/if_bge.c stable/9/sys/dev/bge/if_bgereg.h Directory Properties: stable/9/sys/ (props changed) stable/9/sys/dev/ (props changed) Modified: stable/9/sys/dev/bge/if_bge.c ============================================================================== --- stable/9/sys/dev/bge/if_bge.c Mon Nov 26 02:32:32 2012 (r243537) +++ stable/9/sys/dev/bge/if_bge.c Mon Nov 26 02:41:30 2012 (r243538) @@ -885,7 +885,7 @@ bge_miibus_writereg(device_t dev, int ph if (i == BGE_TIMEOUT) device_printf(sc->bge_dev, - "PHY write timed out (phy %d, reg %d, val %d)\n", + "PHY write timed out (phy %d, reg %d, val 0x%04x)\n", phy, reg, val); return (0); @@ -1466,8 +1466,10 @@ bge_chipinit(struct bge_softc *sc) dma_rw_ctl = BGE_PCIDMARWCTL_RD_CMD_SHIFT(6) | BGE_PCIDMARWCTL_WR_CMD_SHIFT(7); if (sc->bge_flags & BGE_FLAG_PCIE) { - /* Read watermark not used, 128 bytes for write. */ - dma_rw_ctl |= BGE_PCIDMARWCTL_WR_WAT_SHIFT(3); + if (sc->bge_mps >= 256) + dma_rw_ctl |= BGE_PCIDMARWCTL_WR_WAT_SHIFT(7); + else + dma_rw_ctl |= BGE_PCIDMARWCTL_WR_WAT_SHIFT(3); } else if (sc->bge_flags & BGE_FLAG_PCIX) { if (BGE_IS_5714_FAMILY(sc)) { /* 256 bytes for read and write. */ @@ -2034,6 +2036,7 @@ bge_blockinit(struct bge_softc *sc) if (!(BGE_IS_5705_PLUS(sc))) CSR_WRITE_4(sc, BGE_RXLS_MODE, BGE_RXLSMODE_ENABLE); + /* Turn on DMA, clear stats. */ val = BGE_MACMODE_TXDMA_ENB | BGE_MACMODE_RXDMA_ENB | BGE_MACMODE_RX_STATS_CLEAR | BGE_MACMODE_TX_STATS_CLEAR | BGE_MACMODE_RX_STATS_ENB | BGE_MACMODE_TX_STATS_ENB | @@ -2046,7 +2049,6 @@ bge_blockinit(struct bge_softc *sc) else val |= BGE_PORTMODE_MII; - /* Turn on DMA, clear stats */ CSR_WRITE_4(sc, BGE_MAC_MODE, val); DELAY(40); @@ -3186,11 +3188,16 @@ bge_attach(device_t dev) */ sc->bge_flags |= BGE_FLAG_PCIE; sc->bge_expcap = reg; + /* Extract supported maximum payload size. */ + sc->bge_mps = pci_read_config(dev, sc->bge_expcap + + PCIER_DEVICE_CAP, 2); + sc->bge_mps = 128 << (sc->bge_mps & PCIEM_CAP_MAX_PAYLOAD); if (sc->bge_asicrev == BGE_ASICREV_BCM5719 || sc->bge_asicrev == BGE_ASICREV_BCM5720) - pci_set_max_read_req(dev, 2048); - else if (pci_get_max_read_req(dev) != 4096) - pci_set_max_read_req(dev, 4096); + sc->bge_expmrq = 2048; + else + sc->bge_expmrq = 4096; + pci_set_max_read_req(dev, sc->bge_expmrq); } else { /* * Check if the device is in PCI-X Mode. @@ -3399,7 +3406,7 @@ bge_attach(device_t dev) /* The SysKonnect SK-9D41 is a 1000baseSX card. */ if ((pci_read_config(dev, BGE_PCI_SUBSYS, 4) >> 16) == SK_SUBSYSID_9D41 || (hwcfg & BGE_HWCFG_MEDIA) == BGE_MEDIA_FIBER) { - if (BGE_IS_5714_FAMILY(sc)) + if (BGE_IS_5705_PLUS(sc)) sc->bge_flags |= BGE_FLAG_MII_SERDES; else sc->bge_flags |= BGE_FLAG_TBI; @@ -3622,8 +3629,11 @@ bge_reset(struct bge_softc *sc) /* XXX: Broadcom Linux driver. */ if (sc->bge_flags & BGE_FLAG_PCIE) { - if (CSR_READ_4(sc, 0x7E2C) == 0x60) /* PCIE 1.0 */ - CSR_WRITE_4(sc, 0x7E2C, 0x20); + if (sc->bge_asicrev != BGE_ASICREV_BCM5785 && + (sc->bge_flags & BGE_FLAG_5717_PLUS) == 0) { + if (CSR_READ_4(sc, 0x7E2C) == 0x60) /* PCIE 1.0 */ + CSR_WRITE_4(sc, 0x7E2C, 0x20); + } if (sc->bge_chipid != BGE_CHIPID_BCM5750_A0) { /* Prevent PCIE link training during global reset */ CSR_WRITE_4(sc, BGE_MISC_CFG, 1 << 29); @@ -3631,6 +3641,15 @@ bge_reset(struct bge_softc *sc) } } + if (sc->bge_asicrev == BGE_ASICREV_BCM5906) { + val = CSR_READ_4(sc, BGE_VCPU_STATUS); + CSR_WRITE_4(sc, BGE_VCPU_STATUS, + val | BGE_VCPU_STATUS_DRV_RESET); + val = CSR_READ_4(sc, BGE_VCPU_EXT_CTRL); + CSR_WRITE_4(sc, BGE_VCPU_EXT_CTRL, + val & ~BGE_VCPU_EXT_CTRL_HALT_CPU); + } + /* * Set GPHY Power Down Override to leave GPHY * powered up in D0 uninitialized. @@ -3642,15 +3661,6 @@ bge_reset(struct bge_softc *sc) /* Issue global reset */ write_op(sc, BGE_MISC_CFG, reset); - if (sc->bge_asicrev == BGE_ASICREV_BCM5906) { - val = CSR_READ_4(sc, BGE_VCPU_STATUS); - CSR_WRITE_4(sc, BGE_VCPU_STATUS, - val | BGE_VCPU_STATUS_DRV_RESET); - val = CSR_READ_4(sc, BGE_VCPU_EXT_CTRL); - CSR_WRITE_4(sc, BGE_VCPU_EXT_CTRL, - val & ~BGE_VCPU_EXT_CTRL_HALT_CPU); - } - DELAY(1000); /* XXX: Broadcom Linux driver. */ @@ -3667,6 +3677,7 @@ bge_reset(struct bge_softc *sc) PCIEM_CTL_NOSNOOP_ENABLE); pci_write_config(dev, sc->bge_expcap + PCIER_DEVICE_CTL, devctl, 2); + pci_set_max_read_req(dev, sc->bge_expmrq); /* Clear error status. */ pci_write_config(dev, sc->bge_expcap + PCIER_DEVICE_STA, PCIEM_STA_CORRECTABLE_ERROR | @@ -3798,7 +3809,6 @@ bge_reset(struct bge_softc *sc) val = CSR_READ_4(sc, 0x7C00); CSR_WRITE_4(sc, 0x7C00, val | (1 << 25)); } - DELAY(10000); if (sc->bge_asicrev == BGE_ASICREV_BCM5720) BGE_CLRBIT(sc, BGE_CPMU_CLCK_ORIDE, @@ -4088,10 +4098,12 @@ bge_poll(struct ifnet *ifp, enum poll_cm bus_dmamap_sync(sc->bge_cdata.bge_status_tag, sc->bge_cdata.bge_status_map, BUS_DMASYNC_POSTREAD | BUS_DMASYNC_POSTWRITE); + /* Fetch updates from the status block. */ rx_prod = sc->bge_ldata.bge_status_block->bge_idx[0].bge_rx_prod_idx; tx_cons = sc->bge_ldata.bge_status_block->bge_idx[0].bge_tx_cons_idx; statusword = sc->bge_ldata.bge_status_block->bge_status; + /* Clear the status so the next pass only sees the changes. */ sc->bge_ldata.bge_status_block->bge_status = 0; bus_dmamap_sync(sc->bge_cdata.bge_status_tag, @@ -4159,11 +4171,12 @@ bge_intr_task(void *arg, int pending) sc->bge_cdata.bge_status_map, BUS_DMASYNC_POSTREAD | BUS_DMASYNC_POSTWRITE); - /* Save producer/consumer indexess. */ + /* Save producer/consumer indices. */ rx_prod = sc->bge_ldata.bge_status_block->bge_idx[0].bge_rx_prod_idx; tx_cons = sc->bge_ldata.bge_status_block->bge_idx[0].bge_tx_cons_idx; status = sc->bge_ldata.bge_status_block->bge_status; status_tag = sc->bge_ldata.bge_status_block->bge_status_tag << 24; + /* Dirty the status flag. */ sc->bge_ldata.bge_status_block->bge_status = 0; bus_dmamap_sync(sc->bge_cdata.bge_status_tag, sc->bge_cdata.bge_status_map, @@ -5703,7 +5716,7 @@ bge_link_upd(struct bge_softc *sc) bge_miibus_statchg(sc->bge_dev); } - /* Clear the attention. */ + /* Disable MAC attention when link is up. */ CSR_WRITE_4(sc, BGE_MAC_STS, BGE_MACSTAT_SYNC_CHANGED | BGE_MACSTAT_CFG_CHANGED | BGE_MACSTAT_MI_COMPLETE | BGE_MACSTAT_LINK_CHANGED); Modified: stable/9/sys/dev/bge/if_bgereg.h ============================================================================== --- stable/9/sys/dev/bge/if_bgereg.h Mon Nov 26 02:32:32 2012 (r243537) +++ stable/9/sys/dev/bge/if_bgereg.h Mon Nov 26 02:41:30 2012 (r243538) @@ -2802,6 +2802,7 @@ struct bge_softc { struct resource *bge_res; struct ifmedia bge_ifmedia; /* TBI media info */ int bge_expcap; + int bge_expmrq; int bge_msicap; int bge_pcixcap; uint32_t bge_flags; @@ -2845,6 +2846,7 @@ struct bge_softc { uint32_t bge_chiprev; uint8_t bge_asf_mode; uint8_t bge_asf_count; + uint16_t bge_mps; struct bge_ring_data bge_ldata; /* rings */ struct bge_chain_data bge_cdata; /* mbufs */ uint16_t bge_tx_saved_considx;
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?201211260241.qAQ2fU7w074744>