Date: Tue, 27 Nov 2012 14:24:48 +0900 From: YongHyeon PYUN <pyunyh@gmail.com> To: Richard Kuhns <rjk@wintek.com> Cc: "freebsd-stable@freebsd.org" <freebsd-stable@freebsd.org> Subject: Re: bge on the new Mac Mini Message-ID: <20121127052448.GC1452@michelle.cdnetworks.com> In-Reply-To: <50B3872B.9010709@wintek.com> References: <50A65BFC.7030406@wintek.com> <20121120085200.GB1778@michelle.cdnetworks.com> <50AD32A6.8080209@wintek.com> <20121122014921.GA3180@michelle.cdnetworks.com> <20121122020851.GB3180@michelle.cdnetworks.com> <50B3872B.9010709@wintek.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On Mon, Nov 26, 2012 at 10:13:47AM -0500, Richard Kuhns wrote: > On 11/21/12 21:08, YongHyeon PYUN wrote: > > On Thu, Nov 22, 2012 at 10:49:21AM +0900, YongHyeon PYUN wrote: > >> On Wed, Nov 21, 2012 at 02:59:34PM -0500, Richard Kuhns wrote: > >>> On 11/20/12 03:52, YongHyeon PYUN wrote: > >>>> On Fri, Nov 16, 2012 at 10:30:04AM -0500, Richard Kuhns wrote: > >>>>> Hi all, > >>>>> > >>>>> Over the last month or so I've installed FreeBSD 9 (-stable) on several Mac > >>>>> Minis via the memstick image; they seem to be pretty good little boxes for > >>>>> things like offsite secondary nameservers, for example, and they're easily > >>>>> replaced in case of problems. > >>>>> > >>>>> However, the newest minis have slightly different hardware, and FreeBSD can't > >>>>> find the built-in NIC. pciconf -lv on the new mini shows it as > >>>>> > >>>>> none3@pci0:1:0:0: class=0x020000 card=0x168614e4 chip=0x168614e4 rev=0x01 > >>>> > >>>> It seems this controller is BCM57766. > >>>> > >>>>> hdr=0x00 > >>>>> vendor = 'Broadcom Corporation' > >>>>> class = network > >>>>> subclass = ethernet > >>>>> > >>>>> The previous edition mini (that works) reports > >>>>> > >>>>> bge0@pci0:2:0:0: class=0x020000 card=0x16b414e4 chip=0x16b414e4 rev=0x10 hdr=0x00 > >>>>> vendor = 'Broadcom Corporation' > >>>>> device = 'NetXtreme BCM57765 Gigabit Ethernet PCIe' > >>>>> class = network > >>>>> subclass = ethernet > >>>>> > >>>>> Is there a chance that adding the new card/chip info to the current driver would > >>>>> allow it to work? I'll be happy to test and report back. I'm afraid I'm not > >>>>> familiar enough with hardware at that level to figure out the patch myself. > >>>>> > >>>> > >>>> Try attached patch and let me know whether the patch works or not. > >>>> If the patch works please share dmesg output(bge(4) and brgphy(4) > >>>> output only). > >>>> Note, the patch was generated against CURRENT. > >>>> > >>> > >>> I'm afraid it didn't help. I ended up grabbing if_bge.c and if_bgereg.h from > >> > >> I guess you also need to copy brgphy.c from HEAD to > >> /usr/src/sys/dev/mii directory. > >> > >>> HEAD using svnweb.freebsd.org. The patch installed cleanly and there were no > >>> errors during the build, but still no NIC. > >> > >> Does it mean you're not seeing bge0 interface? Or you can't pass > >> any traffic via bge0? > > > > Oops, it seems I've not included your device ID in the diff. > > Try attach one instead. Make sure you use brgphy.c from HEAD. > > > > There's progress! With your latest patch using brgphy.c, if_bge.c, and > if_bgereg.h from head I'm now seeing the bge0 interface. Unfortunately, the > moment I try to configure it the box locks up completely; it won't even toggle > the caps lock LED. > > Booting single user and running ifconfig shows: > > bge0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 > options=8009b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,LINKSTATE> > ether a8:20:66:11:3b:d6 > nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL> > media: Ethernet autoselect (1000baseT <full-duplex>) > status: active > > I did a verbose boot; here's the part that seems to be relevant to bge0: > > bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. 0x57766001> mem > 0xa0400000-0xa040ffff,0xa0410000-0xa041ffff irq 16 at device 0.0 on pci1 > bge0: CHIP ID 0x10110142; ASIC REV 0x10110; CHIP REV 0x101101; PCI-E ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ All these information are garbage which indicates a bug in the diff. > miibus0: <MII bus> on bge0 > brgphy0: <BCM57765 1000BASE-T media interface> PHY 1 on miibus0 > brgphy0: OUI 0x001be9, model 0x0024, rev. 1 > brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, > 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow > bge0: bpf attached > bge0: Ethernet address: a8:20:66:11:3b:d6 > ioapic0: routing intpin 16 (PCI IRQ 16) to lapic 0 vector 61 > > I greatly appreciate your efforts. I'm sorry for the delay getting back with > you, but we had a busy Thanksgiving weekend. > Try again with attached bge.57766.diff3. Thanks for testing!
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20121127052448.GC1452>