Date: Wed, 5 Dec 2001 19:41:15 -0600 (CST) From: Nick Rogness <nick@rogness.net> To: wilko@freebsd.org Cc: freebsd-scsi@freebsd.org, mjacob@feral.com Subject: Re: Qlogic 2100 FC and COMPAQ HSG60 Message-ID: <Pine.BSF.4.21.0112051939510.88137-100000@cody.jharris.com>
next in thread | raw e-mail | index | archive | help
On Thu, 6 Dec 2001, Wilko Bulte wrote:
>> I'm having a couple of issues that I need some help with. I have a
>> Qlogic 2100 FC card connected to a Compaq HSG60 FC controller via a 8
>> port switch. The HSG60 has 10 18.2GB disks tied to it, configured in a
>> RAID5 config. This all resides on a 4.4-STABLE machine (sup'd
>> yesterday).
>>
>> Here's the relative info from dmesg:
>>
>> isp0: <Qlogic ISP 2100 PCI FC-AL Adapter> port 0x1400-0x14ff mem
>> 0x40000000-0x40000fff irq 9 at device 10.0 on pci2
>> ...
>> pass0 at isp0 bus 0 target 129 lun 0
>> pass0: <DEC HSG60CCL V85L> Fixed Storage Arrray SCSI-2 device
>> pass0: 100.000MB/s transfers, Tagged Queueing Enabled
>> pass3 at isp0 bus 0 target 130 lun 0
>> pass3: <DEC HSG60CCL V85L> Fixed Storage Arrray SCSI-2 device
>> pass3: 100.000MB/s transfers, Tagged Queueing Enabled
>
> Is there anything else (other servers) connected to the HSG?
Yes, A W2k machine...but it hasn't been setup.
> What kind of FC switch do you have?
Compaq 8-EL
> If it is a Brocade FC switch, what firmware do you run on the switch?
No, unless Compaq resells it under it's name.
>
>> da0 at isp0 bus 0 target 129 lun 1
>> da0: <DEC HSG60 V85L> Fixed Direct Access SCSI-2 device
>> da0: 100.000MB/s transfers, Tagged Queueing Enabled
>> da0: 103101MB (211152379 512 byte sectors: 255H 63S/T 13143C)
>
> Can I please have a SHOW THIS FULL, a SHOW CONNECTIONS, a SHOW UNITS,
> a SHOW STORAGE from the HSG?
OK, but before you read them, a couple of notes:
-This is running in MultiBus failover
-D1 is the unit allocated to the BSD machine.
-D1 is a partition out of the RAID5-1 raidset
-The BSD machine is UNIX1 & UNIX2 in 'show conn'
Here is the stuff you requested. I also added a "SHOW D1" and a
"SHOW RAID5-1":
Controller-1> SHOW THIS FULL
Controller:
HSG60 ZG01800744 Software V85L-0, Hardware E11
NODE_ID = 5000-1FE1-0008-3150
ALLOCATION_CLASS = 0
SCSI_VERSION = SCSI-3
Configured for MULTIBUS_FAILOVER with ZG03202522
In dual-redundant configuration
Device Port SCSI address 7
Time: NOT SET
Command Console LUN is lun 0 (IDENTIFIER = 2)
Host PORT_1:
Reported PORT_ID = 5000-1FE1-0008-3153
PORT_1_TOPOLOGY = FABRIC (fabric up)
Address = 011100
Host PORT_2:
Reported PORT_ID = 5000-1FE1-0008-3154
PORT_2_TOPOLOGY = OFFLINE (offline)
NOREMOTE_COPY
Cache:
128 megabyte write cache, version 0022
Cache is GOOD
No unflushed data in cache
CACHE_FLUSH_TIMER = DEFAULT (10 seconds)
Mirrored Cache:
128 megabyte write cache, version 0022
Cache is GOOD
No unflushed data in cache
Battery:
NOUPS
FULLY CHARGED
Expires: 26-NOV-2003
Extended information:
Terminal speed 9600 baud, eight bit, no parity, 1 stop bit
Operation control: 00000000 Security state code: 98063
Configuration backup disabled
Controller-1> SHOW CONN
Connection Unit
Name Operating system Controller Port Address Status Offset
CALLISTO1 WINNT THIS 1 011601 OL this 10
HOST_ID=2000-0000-C922-67F3 ADAPTER_ID=1000-0000-C922-67F3
CALLISTO2 WINNT OTHER 1 011601 OL other 0
HOST_ID=2000-0000-C922-67F3 ADAPTER_ID=1000-0000-C922-67F3
UNIX1 WINNT THIS 1 0114EF OL this 0
HOST_ID=2000-00E0-8B01-EC20 ADAPTER_ID=2100-00E0-8B01-EC20
UNIX2 WINNT OTHER 1 0114EF OL other 0
HOST_ID=2000-00E0-8B01-EC20 ADAPTER_ID=2100-00E0-8B01-EC20
Controller-1> SHOW UNIT
LUN Uses Used by
------------------------------------------------------------------------------
D1 RAID5-1 (partition)
D2 RAID5-1 (partition)
D3 M1
Controller-1> SHOW STORAGE
Name Storageset Uses Used by
------------------------------------------------------------------------------
M1 mirrorset DISK20400 D3
RAID5-1 raidset DISK10000 D1
DISK10100 D2
DISK10200
DISK10300
DISK10400
DISK20000
DISK20100
DISK20200
DISK20300
DISK20800
SPARESET spareset
FAILEDSET failedset
Controller-1> SHOW D1
LUN Uses Used by
------------------------------------------------------------------------------
D1 RAID5-1 (partition)
LUN ID: 6000-1FE1-0008-3150-0009-0180-0744-0098
IDENTIFIER = 1
Switches:
RUN NOWRITE_PROTECT READ_CACHE
READAHEAD_CACHE WRITEBACK_CACHE
MAXIMUM_CACHED_TRANSFER_SIZE = 32
Access:
UNIX1, UNIX2
State:
ONLINE to the other controller
PREFERRED_PATH = THIS_CONTROLLER
Size: 211152379 blocks
Geometry (C/H/S): ( 41566 / 20 / 254 )
Controller-1> SHOW RAID5-1
Name Storageset Uses Used by
------------------------------------------------------------------------------
RAID5-1 raidset DISK10000 D1
DISK10100 D2
DISK10200
DISK10300
DISK10400
DISK20000
DISK20100
DISK20200
DISK20300
DISK20800
Switches:
POLICY (for replacement) = BEST_PERFORMANCE
RECONSTRUCT (priority) = NORMAL
CHUNKSIZE = 128 blocks
State:
NORMAL
DISK10000 (member 0) is NORMAL
DISK10100 (member 1) is NORMAL
DISK10200 (member 2) is NORMAL
DISK10300 (member 3) is NORMAL
DISK10400 (member 4) is NORMAL
DISK20800 (member 5) is NORMAL
DISK20000 (member 6) is NORMAL
DISK20100 (member 7) is NORMAL
DISK20200 (member 8) is NORMAL
DISK20300 (member 9) is NORMAL
Size: 319929345 blocks
Partitions:
Partition number Size Starting Block Used by
---------------------------------------------------------------------
1 211152379 ( 108110.01 MB) 0 D1
2 108776956 ( 55693.80 MB) 211152384 D2
Anyway there you have it. I don't know if this is configured wrong or
not.
Nick Rogness <nick@rogness.net>
- Keep on Routing in a Free World...
"FreeBSD: The Power to Serve!"
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-scsi" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.4.21.0112051939510.88137-100000>