Date: Wed, 02 Jul 2008 12:54:17 -0700 From: Sam Leffler <sam@freebsd.org> To: Alexander Sack <pisymbol@gmail.com> Cc: FreeBSD STABLE <freebsd-stable@freebsd.org> Subject: Re: Atheros (ath) MSI wireless embedded chipset fails to attach on 7.0-STABLE Message-ID: <486BDCE9.3000608@freebsd.org> In-Reply-To: <3c0b01820806170757v5565b59ne0e9d5db06f26761@mail.gmail.com> References: <3c0b01820806170757v5565b59ne0e9d5db06f26761@mail.gmail.com>
next in thread | previous in thread | raw e-mail | index | archive | help
Alexander Sack wrote: > Hello: > > I have installed FreeBSD-7.0-amd64 stable on my new AMD X2 Turon based > notebook, a MSI-1710A (GX710Ax) which has a generic embedded > controller. During boot up I notice that ATH complains with: > > ath_rate: version 1.2 <SampleRate bit-rate selection algorithm> > ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) > ath0: <Atheros 5424/2424> mem 0xfd7f0000-0xfd7fffff irq 16 at device 0.0 on pci2 > ath0: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xfd7f0000 > ath0: [MPSAFE] > ath0: [ITHREAD] > ath0: unable to attach hardware; HAL status 13 > device_attach: ath0 attach returned 6 > > HAL status 13 from the header file seems to indicate that the > 7.0-STABLE driver doesn't support my hardware revision. Here is my > pciconf -l output: > > hostb0@pci0:0:0:0: class=0x060000 card=0x42cd1462 chip=0x79101002 > rev=0x00 hdr=0x00 > pcib1@pci0:0:2:0: class=0x060400 card=0x42cd1462 chip=0x79131002 > rev=0x00 hdr=0x01 > pcib2@pci0:0:4:0: class=0x060400 card=0x42cd1462 chip=0x79141002 > rev=0x00 hdr=0x01 > pcib3@pci0:0:6:0: class=0x060400 card=0x42cd1462 chip=0x79161002 > rev=0x00 hdr=0x01 > pcib4@pci0:0:7:0: class=0x060400 card=0x42cd1462 chip=0x79171002 > rev=0x00 hdr=0x01 > atapci0@pci0:0:18:0: class=0x01018f card=0x42cd1462 chip=0x43801002 > rev=0x00 hdr=0x00 > ohci0@pci0:0:19:0: class=0x0c0310 card=0x42cd1462 chip=0x43871002 > rev=0x00 hdr=0x00 > ohci1@pci0:0:19:1: class=0x0c0310 card=0x42cd1462 chip=0x43881002 > rev=0x00 hdr=0x00 > ohci2@pci0:0:19:2: class=0x0c0310 card=0x42cd1462 chip=0x43891002 > rev=0x00 hdr=0x00 > ohci3@pci0:0:19:3: class=0x0c0310 card=0x42cd1462 chip=0x438a1002 > rev=0x00 hdr=0x00 > ohci4@pci0:0:19:4: class=0x0c0310 card=0x42cd1462 chip=0x438b1002 > rev=0x00 hdr=0x00 > ehci0@pci0:0:19:5: class=0x0c0320 card=0x42cd1462 chip=0x43861002 > rev=0x00 hdr=0x00 > none0@pci0:0:20:0: class=0x0c0500 card=0x42cd1462 chip=0x43851002 > rev=0x14 hdr=0x00 > atapci1@pci0:0:20:1: class=0x01018a card=0x42cd1462 chip=0x438c1002 > rev=0x00 hdr=0x00 > none1@pci0:0:20:2: class=0x040300 card=0x42cd1462 chip=0x43831002 > rev=0x00 hdr=0x00 > isab0@pci0:0:20:3: class=0x060100 card=0x42cd1462 chip=0x438d1002 > rev=0x00 hdr=0x00 > pcib5@pci0:0:20:4: class=0x060401 card=0x00000000 chip=0x43841002 > rev=0x00 hdr=0x01 > hostb1@pci0:0:24:0: class=0x060000 card=0x00000000 chip=0x11001022 > rev=0x00 hdr=0x00 > hostb2@pci0:0:24:1: class=0x060000 card=0x00000000 chip=0x11011022 > rev=0x00 hdr=0x00 > hostb3@pci0:0:24:2: class=0x060000 card=0x00000000 chip=0x11021022 > rev=0x00 hdr=0x00 > hostb4@pci0:0:24:3: class=0x060000 card=0x00000000 chip=0x11031022 > rev=0x00 hdr=0x00 > vgapci0@pci0:1:0:0: class=0x030000 card=0x42cd1462 chip=0x95811002 > rev=0x00 hdr=0x00 > none2@pci0:1:0:1: class=0x040300 card=0xaa081462 chip=0xaa081002 > rev=0x00 hdr=0x00 > ath0@pci0:2:0:0: class=0x020000 card=0x10261a3b chip=0x001c168c > rev=0x01 hdr=0x00 > re0@pci0:5:0:0: class=0x020000 card=0x42cd1462 chip=0x816810ec rev=0x01 hdr=0x00 > cbb0@pci0:6:4:0: class=0x060700 card=0x42cd1462 chip=0x71341217 > rev=0x21 hdr=0x02 > none3@pci0:6:4:2: class=0x080500 card=0x42cd1462 chip=0x71201217 > rev=0x01 hdr=0x00 > none4@pci0:6:4:3: class=0x068000 card=0x42cd1462 chip=0x71301217 > rev=0x01 hdr=0x00 > fwohci0@pci0:6:4:4: class=0x0c0010 card=0x42cd1462 chip=0x00f71217 > rev=0x02 hdr=0x00 > > ath0 is listed as rev=0x01 so I'm a little confused why I got HAL > status 13. Does anyone know if this chipset is supported in > 7.0-STABLE? If not, is it possible to try CURRENT on 7.0 which may > fix it? I've attached my complete dmesg output. > > Again, any feedback would be much appreciated! > > Try the hal in http://www.freebsd.org/~sam. Sam
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?486BDCE9.3000608>