Date: Sat, 24 Aug 2002 16:10:42 -0400 From: Anish Mistry <mistry.7@osu.edu> To: freebsd-mobile@freebsd.org Subject: Fujitsu P2000 (2110) USB Problem Message-ID: <200208241610.42334.mistry.7@osu.edu>
next in thread | raw e-mail | index | archive | help
I am having a problem getting any sort of USB device to work with my Fu=
jitsu=20
P2000 notebook. The USB works correctly in window 2000 so I know that th=
e=20
hardware is ok.
The problem is that I can plug in a USB device ie. a floppy drive and a=
=20
little kernel message appears notifying me that it is plugged in, but the=
n I=20
am not able to mount it. Then I try my USB Visor. Plug it in press the=20
button, device message shows up, but can't communicate with the device. =
Not=20
being one to give up I recompiled my kernel for rio mp3 player support. =20
installed rioutil and tryed again. Plug it in, device shows up as rio0, =
but=20
when I try to query information from it: rioutil -i. It just hangs and I=
=20
have to [ctl]-c it.
I've pasted my dmesg below. Is there anything else that I can send th=
at=20
would help? I don't have any problems with coding if it comes to that. =20
Thanks.
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.6-STABLE #9: Sat Aug 24 14:28:54 EDT 2002
root@littleguy.am-productions.biz:/usr/obj/usr/src/sys/LITTLEGUY
Timecounter "i8254" frequency 1193182 Hz
CPU: Transmeta(tm) Crusoe(tm) Processor TM5800 (713.25-MHz 586-class CPU)
Origin =3D "GenuineTMx86" Id =3D 0x543
real memory =3D 251527168 (245632K bytes)
avail memory =3D 240992256 (235344K bytes)
Preloaded elf kernel "kernel" at 0xc03c0000.
md0: Malloc disk
Using $PIR table, 9 entries at 0xc00fdf30
apm0: <APM BIOS> on motherboard
apm: found APM BIOS v1.2, connected at v1.2
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pci0: <unknown card> (vendor=3D0x1279, dev=3D0x0396) at 0.1
pci0: <unknown card> (vendor=3D0x1279, dev=3D0x0397) at 0.2
ohci0: <AcerLabs M5237 (Aladdin-V) USB controller> mem 0xfc004000-0xfc004=
fff=20
irq 11 at device 2.0 on pci0
usb0: OHCI version 1.0, legacy support
usb0: <AcerLabs M5237 (Aladdin-V) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: AcerLabs OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pcm0: <Acer Labs M5451> port 0x1000-0x10ff mem 0xfc005000-0xfc005fff irq =
9 at=20
device 4.0 on pci0
chip1: <AcerLabs M15x3 Power Management Unit> at device 6.0 on pci0
isab0: <AcerLabs M1533 portable PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
pcic0: <TI PCI-1410 PCI-CardBus Bridge> irq 9 at device 12.0 on pci0
pcic0: PCI Memory allocated: 0x88000000
pcic0: TI12XX PCI Config Reg: [ring enable][speaker enable][pwr save][FUN=
C pci=20
int + CSC serial isa irq]
pccard0: <PC Card bus (classic)> on pcic0
atapci0: <AcerLabs Aladdin ATA66 controller> port 0x1800-0x180f irq 0 at=20
device 15.0 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
rl0: <RealTek 8139 10/100BaseTX> port 0x8000-0x80ff mem 0xfc007800-0xfc00=
78ff=20
irq 9 at device 16.0 on pci0
rl0: Ethernet address: 00:e0:00:ae:45:08
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci0: <unknown card> (vendor=3D0x104c, dev=3D0x8026) at 19.0 irq 9
pci0: <ATI RageMobility-P/M graphics accelerator> at 20.0 irq 9
orm0: <Option ROM> at iomem 0xc0000-0xcffff on isa0
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=3D0x300>
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250
sio1: configured irq 3 not in bitmap of probed irqs 0
ad0: 19077MB <TOSHIBA MK2018GAP> [38760/16/63] at ata0-master UDMA66
acd0: CD-RW <TOSHIBA DVD-ROM SD-R2212> at ata1-master UDMA33
Mounting root from ufs:/dev/ad0s2a
LongRun: Transmeta Crusoe series CPU's power management feature
LongRun mode: 1 533MHz 1100mV 41%can't re-use a leaf (longrun)!
can't re-use a leaf (frequency)!
can't re-use a leaf (voltage)!
can't re-use a leaf (percentage)!
umass0: NEC NEC USB UF000x, rev 1.10/1.21, addr 2
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <NEC USB UF000x 1.21> Removable Direct Access SCSI-0 device
da0: 20KB/s transfers
da0: 1MB (2880 512 byte sectors: 2H 18S/T 80C)
umass0: Unsupported UFI command 0x08, 6 byte command should have been=20
converted
da0: reading primary partition table: error reading fsbn 0
umass0: Unsupported UFI command 0x35
(da0:umass-sim0:0:0:0): Synchronize cache failed, status =3D=3D 0x6, scsi=
status=20
=3D=3D 0x0
--=20
Anish Mistry
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-mobile" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200208241610.42334.mistry.7>