Date: Thu, 11 Nov 2010 09:14:30 -0200 From: Luiz Otavio O Souza <lists.br@gmail.com> To: Milan Obuch <freebsd-mips@dino.sk> Cc: freebsd-mips@freebsd.org Subject: Re: First RSPRO deployed ! Message-ID: <2ECB603F-5E21-424E-8EF7-5F7189887AEC@gmail.com> In-Reply-To: <201011101616.59156.freebsd-mips@dino.sk> References: <D74327E9-0A8A-4B46-B4DD-16D0FAF8E3BB@gmail.com> <201011101616.59156.freebsd-mips@dino.sk>
next in thread | previous in thread | raw e-mail | index | archive | help
On Nov 10, 2010, at 1:16 PM, Milan Obuch wrote: > On Wednesday 10 November 2010 13:21:55 Luiz Otavio O Souza wrote: >> Hello everyone, >>=20 >> This is just a FYI about my first RSPRO deployed and my satisfaction = with >> it :) >>=20 >=20 > Hi, >=20 >> I'm running a slightly modified version of current (for the RTC = support and >> basic multi-phy/switch support - still without vlan support). >>=20 >=20 > Could you share your changes/patches? I have this board too and could = benefit=20 > from it too... you did a bit more already than me... Hi Milan, Sure, all my patches/changes are available, but as i said, it's only = small changes... >> I've replaced my old P4 server and my (also old) wireless AP by this = RSPRO >> with a ubiquiti SR-2 card. >>=20 >=20 > Hm, interesting, What do you use it for? >=20 It is just a home/office router with low traffic (cheap cable = connection) but with a few 24x7 connections (so i'm more for stability = and features than speed). >> The only problem i had was with the WPA - hostapd - setup (never did = it >> before, so i probably have screwed the setup). >>=20 >=20 > If you could show config, maybe someone could help you. I have tested = WPA=20 > setup with two FreeBSD systems and Atheros cards and it worked. I = could use my=20 > FreeBSD AP as an internet gateway for wifi enabled Nokia E66, too, so = I think=20 > a verified it a bit :) and this kind of things should not be arch = dependent :) Here is my config (ifconfig - rc.conf): hostapd_enable=3D"YES" wlans_ath0=3D"wlan1" create_args_wlan1=3D"wlanmode hostap mode 11g descr wireless-ap" ifconfig_wlan1=3D"ssid wpa-test channel 1" My hostapd.conf: http://pastebin.com/fz6pNfHX (have tried with and without preamble, with eapol_version =3D 1 and 2 = and with wpa =3D 1 and 3) Here is the syslog output: http://pastebin.com/YaQHtfVr The problem is, i've only an iphone to test this atm... I've another ubiquiti card and another rspro, i'll try to test the wpa = setup using a freebsd client and check if something changes (that's why = i did not asked for help at first time, i've not tried everything yet - = but help is always welcome). >=20 >> Here is the dmesg: http://pastebin.com/BGsAun6b >>=20 >> The ifconfig: http://pastebin.com/Vf5pqaQs >>=20 >> Disks and slices: http://pastebin.com/2jc0fJPh >>=20 >> GPIO devices: http://pastebin.com/FvhQW5iL >>=20 >> All installed ports: http://pastebin.com/yHcszFpR >>=20 >> It's running fully static, booting a gziped kernel from onboard flash = and >> with a full system on a 8GB SD card (i've another two 4GB memsticks, = one >> is used for ports and the other for sources and obj). >>=20 >=20 > Again, it would be great if you could share your experience - I would = like to=20 > run from flash too, but did not came there yet, I am still only at = netboot=20 > stage with USB flasdisk based file system. >=20 > Regards, > Milan adrian@ keeps a wiki page with some information about this: = http://wiki.freebsd.org/AdrianChadd/UbiquityRouterstationPro I'll poke him about a port for this flash tool, it's very simple to use. I'll also send some of my patches to mailing list. If you need anything else (or if i forget something), just ask :) Regards, Luiz PS: i need some days to rebuild my development environment, it's all off = now... i'm enjoying the silence :)=
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?2ECB603F-5E21-424E-8EF7-5F7189887AEC>