Date: Fri, 04 Jan 2002 00:35:04 +0000 From: Pete French <pfrench@firstcallgroup.co.uk> To: freebsd-stable@FreeBSD.ORG Subject: PCMCIA card problems with 4.5-PRERELEASE Message-ID: <E16MIK8-0003Bp-00@mailhost.firstcallgroup.co.uk>
next in thread | raw e-mail | index | archive | help
So, for the first time I actually have a laptop that I can play with to
try out FreeBSD on. It has a single PCMCIA slot, and requires the ISA
bus interrupt routing which has been mentioned here many times.
I couldnt work out a way to set these variables as part of the install
process, so I installed 4.3 first and then upgraded to 4.5-PRE by
copying over a compiled up /usr/src and /usr/obj tar file via the widdows
partition and mount_msdos. This is very successful and the laptop now
runs 4.5-PRE quite happily.
But even with the IRQ routing set to ISA then I still cannot make PCMCIA
cards work. Insreting or removing cards will lock the machine, O.K. I can
live with that as long as they work when I boot with them.
Booting with a card seems to be fine. The system detects it, and apparently
runs the correct commands to try and configure it. I have two cards to
try - an Etherlink III 3C589D and an Adaptec SlimSCSI APA-1460A.
Firstly the ether card. This is recognised, an ifconfig appears to
tell me that the interface is correctly up. If I try and ppin any
other achines on the nwtwork I see packets being transmitted. However no
packets are ever received by the machine. With the card in the ifconfig
on the interface is as follows...
ep0: flags=a843<UP,BROADCAST,RUNNING,SIMPLEX,LINK1,MULTICAST> mtu 1500
inet 192.168.3.3 netmask 0xffffff00 broadcast 192.168.3.255
inet6 fe80::260:97ff:fe8e:e04%ep0 prefixlen 64 scopeid 0x6
ether 00:60:97:8e:0e:04
media: Ethernet 10baseT/UTP
Secondly the SCSI card (this is connected to an external Yamaha CDW4416SX).
This also appears to be detected correctly and boots. So I tried a quick
scan of the bus using 'camcontrol rescan 0'. This pauses for some time and
then generates the following error message repeatedly:
(probe0:aic1:0:0:0): ccb 0x0b90800 - timed out, phase 0x0, state 1
So, any ideas anyone ? To my untrained eye it looks like the cards are having
[problems communicating back to the system (received backets, indications
of completed SCSi commands ?). I have included below the dmesg outputs,
firstly from a boot with the ether card, secondly from a boot with the scsi
card. cheers,
-pete french.
PS: The laptop is a Palmax PD-1100 if that helps...
----------------------------- dmesg.ether -------------------------------
Copyright (c) 1992-2001 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.5-PRERELEASE #0: Sat Dec 29 18:57:01 GMT 2001
pete@skerry:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz
CPU: Cyrix GXm (262.39-MHz 586-class CPU)
Origin = "CyrixInstead" Id = 0x540 DIR=0x6347 Stepping=6 Revision=3
real memory = 64487424 (62976K bytes)
avail memory = 58077184 (56716K bytes)
Preloaded elf kernel "kernel" at 0xc0490000.
md0: Malloc disk
Using $PIR table, 2 entries at 0xc00fdfa0
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcic0: <TI PCI-1211 PCI-CardBus Bridge> at device 11.0 on pci0
pcic0: PCI Memory allocated: 0x44000000
pcic0: Polling mode
pcic0: TI12XX PCI Config Reg: [ring enable][speaker enable][CSC parallel isa irq]
pccard0: <PC Card bus (classic)> on pcic0
isab0: <Cyrix Cx5530 PCI-ISA bridge> at device 18.0 on pci0
isa0: <ISA bus> on isab0
chip1: <PCI to Other bridge (vendor=1078 device=0101)> mem 0x40012000-0x400120ff at device 18.1 on pci0
atapci0: <Cyrix 5530 ATA33 controller> port 0xfc00-0xfc0f at device 18.2 on pci0
atapci0: Busmastering DMA not supported
pci0: <unknown card> (vendor=0x1078, dev=0x0103) at 18.3
pci0: <VGA-compatible display device> at 18.4
ohci0: <OHCI (generic) USB controller> mem 0xfedff000-0xfedfffff irq 11 at device 19.0 on pci0
usb0: OHCI version 1.0, legacy support
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: (unknown) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
orm0: <Option ROM> at iomem 0xc0000-0xc7fff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
ata1 at port 0x170-0x177,0x376 irq 15 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ad0: 9590MB <FUJITSU MHN2100AT> [19485/16/63] at ata0-master BIOSPIO
Mounting root from ufs:/dev/ad0s2a
pccard: card inserted, slot 0
ep0: <3Com Etherlink III 3C589> at port 0x240-0x24f irq 5 slot 0 on pccard0
ep0: Ethernet address 00:60:97:8e:0e:04
----------------------------- dmesg.scsi --------------------------------
Copyright (c) 1992-2001 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.5-PRERELEASE #0: Sat Dec 29 18:57:01 GMT 2001
pete@skerry:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz
CPU: Cyrix GXm (262.39-MHz 586-class CPU)
Origin = "CyrixInstead" Id = 0x540 DIR=0x6347 Stepping=6 Revision=3
real memory = 64487424 (62976K bytes)
avail memory = 58077184 (56716K bytes)
Preloaded elf kernel "kernel" at 0xc0490000.
md0: Malloc disk
Using $PIR table, 2 entries at 0xc00fdfa0
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcic0: <TI PCI-1211 PCI-CardBus Bridge> at device 11.0 on pci0
pcic0: PCI Memory allocated: 0x44000000
pcic0: Polling mode
pcic0: TI12XX PCI Config Reg: [ring enable][speaker enable][CSC parallel isa irq]
pccard0: <PC Card bus (classic)> on pcic0
isab0: <Cyrix Cx5530 PCI-ISA bridge> at device 18.0 on pci0
isa0: <ISA bus> on isab0
chip1: <PCI to Other bridge (vendor=1078 device=0101)> mem 0x40012000-0x400120ff at device 18.1 on pci0
atapci0: <Cyrix 5530 ATA33 controller> port 0xfc00-0xfc0f at device 18.2 on pci0
atapci0: Busmastering DMA not supported
pci0: <unknown card> (vendor=0x1078, dev=0x0103) at 18.3
pci0: <VGA-compatible display device> at 18.4
ohci0: <OHCI (generic) USB controller> mem 0xfedff000-0xfedfffff irq 11 at device 19.0 on pci0
usb0: OHCI version 1.0, legacy support
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: (unknown) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
orm0: <Option ROM> at iomem 0xc0000-0xc7fff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
ata1 at port 0x170-0x177,0x376 irq 15 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ad0: 9590MB <FUJITSU MHN2100AT> [19485/16/63] at ata0-master BIOSPIO
Mounting root from ufs:/dev/ad0s2a
pccard: card inserted, slot 0
aic1: <Adaptec 6260/6360 SCSI controller> at port 0x340-0x35f irq 5 slot 0 on pccard0
aic1: aic6360, dma, disconnection, parity check
(probe0:aic1:0:0:0): ccb 0xc0b90800 - timed out, phase 0x0, state 1
(probe0:aic1:0:0:0): ccb 0xc0b90800 - timed out, phase 0x0, state 1
(probe0:aic1:0:0:0): ccb 0xc0b90800 - timed out, phase 0x0, state 1
(probe0:aic1:0:0:0): ccb 0xc0b90800 - timed out, phase 0x0, state 1
(probe0:aic1:0:0:0): ccb 0xc0b90800 - timed out, phase 0x0, state 1
(probe0:aic1:0:0:0): ccb 0xc0b90800 - timed out, phase 0x0, state 1
(probe0:aic1:0:0:0): ccb 0xc0b90800 - timed out, phase 0x0, state 1
(probe0:aic1:0:0:0): ccb 0xc0b90800 - timed out, phase 0x0, state 1
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-stable" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?E16MIK8-0003Bp-00>