Date: Sat, 15 Mar 2003 14:33:49 +0100 From: "INV/Stefan K." <eSKa@gmx.info> To: freebsd-mobile@freebsd.org Subject: Problems with Xircom 32-Bit Cardbus on 5.0-REL Message-ID: <3E732BBD.8080907@gmx.info>
index | next in thread | raw e-mail
Hello,
I have problems getting a Xircom Realport Cardbus RBEM56G-100 to
work on a Toshiba Tecra 8000 Notebook with 5.0-RELEASE.
I use the generic kernel on the system, the card has been activated
but cannot assign an ip-address with ifconfig to it. The system will hang
immediately and I have to turn it off.
I have attached the output of dmesg, ifconfig and scanpci. Maybe someone
of, possibly you, had the same problem and solved it successfully.
In this case it would be great, if you contact me and tell how you did go
about it.
Sincerely,
Stefan Kapfhammer
RE/MAX Germany
Office Nurembourg
OUTPUT OF IFCONFIG:
===================
lp0: flags=8810<POINTOPOINT,SIMPLEX,MULTICAST> mtu 1500
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2
inet 127.0.0.1 netmask 0xff000000
dc0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
ether 06:00:10:a4:f8:06
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
OUTPUT OF DMESG bootopts hw.cardbus.debug=1 and hw.cardbus.cis_debug=1
==================================================================
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.0-RELEASE #0: Thu Jan 16 22:16:53 GMT 2003
root@hollin.btc.adaptec.com:/usr/obj/usr/src/sys/GENERIC
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0673000.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc06730a8.
Timecounter "i8254" frequency 1193182 Hz
Timecounter "TSC" frequency 399924390 Hz
CPU: Pentium II/Pentium II Xeon/Celeron (399.92-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x66a Stepping = 10
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
real memory = 268369920 (255 MB)
avail memory = 253771776 (242 MB)
Initializing GEOMetry subsystem
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <TOSHIB 750 > on motherboard
ACPI-0625: *** Info: GPE Block0 defined as GPE0 to GPE15
acpi0: power button is handled as a fixed feature programming model.
Timecounter "ACPI-safe" frequency 3579545 Hz
acpi_timer0: <24-bit timer at 3.579545MHz> port 0xfe08-0xfe0b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_tz0: <thermal zone> on acpi0
Using $PIR table, 6 entries at 0xc00f1320
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: <display, VGA> at device 4.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 5.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xfe60-0xfe6f at device 5.1
on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xffe0-0xffff irq
11 at device 5.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ugen0: Avision USB Scanner, rev 1.10/0.00, addr 2
pci0: <bridge, PCI-unknown> at device 5.3 (no driver attached)
pci0: <simple comms> at device 9.0 (no driver attached)
cbb0: <ToPIC97 PCI-CardBus Bridge> at device 11.0 on pci0
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
pcib0: slot 11 INTA is routed to irq 11
cbb1: <ToPIC97 PCI-CardBus Bridge> at device 11.1 on pci0
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
pcib0: slot 11 INTB is routed to irq 11
pci0: <multimedia> at device 13.0 (no driver attached)
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_cmbat0: <Control method Battery> on acpi0
acpi_cmbat1: <Control method Battery> on acpi0
acpi_acad0: <AC adapter> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
fdc0: <NEC 765 or clone> port 0x3f7,0x3f2-0x3f5 irq 6 drq 2 on acpi0
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
ppc0 port 0x778-0x77a,0x378-0x37f irq 7 drq 3 on acpi0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
orm0: <Option ROM> at iomem 0xc0000-0xcbfff on isa0
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 10.000 msec
Product version: 5.0
Product name: Xircom | CardBus Ethernet 10/100 + Modem 56 | CBEM56G | 1.03
|
Manufacturer ID: 0501030181
Functions: Network Adaptor, Multi-Functioned
Function Extension: 04060010a4f80646
Function Extension: 0102
Function Extension: 0280969800
Function Extension: 0200e1f505
Function Extension: 0301
Function Extension: 0303
Function Extension: 0501
cardbus0: Invalid BAR number: 27(06)
CIS reading done
dc0: <Xircom X3201 10/100BaseTX> port 0x1000-0x107f mem
0x88002000-0x880020ff,0x88002100-0x8800217f
irq 11 at device 0.0 on cardbus0
dc0: Ethernet address: 06:00:10:a4:f8:06
miibus0: <MII bus> on dc0
tdkphy0: <TDK 78Q2120 media interface> on miibus0
tdkphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
Product version: 5.0
Product name: Xircom | CardBus Ethernet 10/100 + Modem 56 | CBEM56G | 1.03
|
Manufacturer ID: 0501001081
Functions: Serial Port, Multi-Functioned
Function Extension: 00020f5c
Function Extension: 0206003f1c03030f070001b5
Function Extension: 1306000b000200b5
cardbus0: Invalid BAR number: 27(06)
CIS reading done
cardbus0: <unknown card> (vendor=0x115d, dev=0x0103) at 0.1 irq 11
ata1-slave: timeout waiting for interrupt
ata1-slave: ATAPI identify failed
ad0: 13481MB <IBM-DCYA-214000> [27390/16/63] at ata0-master UDMA33
acd0: DVD-ROM <TOSHIBA DVD-ROM SD-C2102> at ata1-master PIO4
Mounting root from ufs:/dev/ad0s1a
Waiting (max 60 seconds) for system process `vnlru' to stop...stopped
Waiting (max 60 seconds) for system process `bufdaemon' to stop...stopped
Waiting (max 60 seconds) for system process `syncer' to stop...stopped
syncing disks, buffers remaining... 2 2 2 2 2
done
Uptime: 56m30s
Terminate ACPI
Rebooting...
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.0-RELEASE #0: Thu Jan 16 22:16:53 GMT 2003
root@hollin.btc.adaptec.com:/usr/obj/usr/src/sys/GENERIC
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0673000.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc06730a8.
Timecounter "i8254" frequency 1193182 Hz
Timecounter "TSC" frequency 399923279 Hz
CPU: Pentium II/Pentium II Xeon/Celeron (399.92-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x66a Stepping = 10
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
real memory = 268369920 (255 MB)
avail memory = 253771776 (242 MB)
Initializing GEOMetry subsystem
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <TOSHIB 750 > on motherboard
ACPI-0625: *** Info: GPE Block0 defined as GPE0 to GPE15
acpi0: power button is handled as a fixed feature programming model.
Timecounter "ACPI-safe" frequency 3579545 Hz
acpi_timer0: <24-bit timer at 3.579545MHz> port 0xfe08-0xfe0b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_tz0: <thermal zone> on acpi0
Using $PIR table, 6 entries at 0xc00f1320
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: <display, VGA> at device 4.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 5.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xfe60-0xfe6f at device 5.1
on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xffe0-0xffff irq
11 at device 5.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ugen0: Avision USB Scanner, rev 1.10/0.00, addr 2
pci0: <bridge, PCI-unknown> at device 5.3 (no driver attached)
pci0: <simple comms> at device 9.0 (no driver attached)
cbb0: <ToPIC97 PCI-CardBus Bridge> at device 11.0 on pci0
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
pcib0: slot 11 INTA is routed to irq 11
cbb1: <ToPIC97 PCI-CardBus Bridge> at device 11.1 on pci0
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
pcib0: slot 11 INTB is routed to irq 11
pci0: <multimedia> at device 13.0 (no driver attached)
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_cmbat0: <Control method Battery> on acpi0
acpi_cmbat1: <Control method Battery> on acpi0
acpi_acad0: <AC adapter> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
fdc0: <NEC 765 or clone> port 0x3f7,0x3f2-0x3f5 irq 6 drq 2 on acpi0
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
ppc0 port 0x778-0x77a,0x378-0x37f irq 7 drq 3 on acpi0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
orm0: <Option ROM> at iomem 0xc0000-0xcbfff on isa0
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 10.000 msec
found-> vendor=0x115d, dev=0x0003, revid=0x03
class=02-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0xa8 (5040 ns), mingnt=0x14 (5000 ns), maxlat=0x28 (10000 ns)
intpin=a, irq=255
Product version: 5.0
Product name: Xircom | CardBus Ethernet 10/100 + Modem 56 | CBEM56G | 1.03
|
Manufacturer ID: 0501030181
Functions: Network Adaptor, Multi-Functioned
Function Extension: 04060010a4f80646
Function Extension: 0102
Function Extension: 0280969800
Function Extension: 0200e1f505
Function Extension: 0301
Function Extension: 0303
Function Extension: 0501
cardbus0: Opening BAR: type=IO, bar=10, len=0080
cardbus0: Opening BAR: type=MEM, bar=14, len=0080
cardbus0: Opening BAR: type=MEM, bar=18, len=0100
cardbus0: Invalid BAR number: 27(06)
CIS reading done
cardbus0: Non-prefetchable memory at 88002000-8800217f
cardbus0: Non-prefetchable memory rid=18 at 88002000-880020ff (100)
cardbus0: Non-prefetchable memory rid=14 at 88002100-8800217f (80)
cardbus0: IO port at 1000-107f
cardbus0: IO port rid=10 at 1000-107f
dc0: <Xircom X3201 10/100BaseTX> port 0x1000-0x107f mem
0x88002000-0x880020ff,0x88002100-0x8800217f
irq 11 at device 0.0 on cardbus0
dc0: Ethernet address: 06:00:10:a4:f8:06
miibus0: <MII bus> on dc0
tdkphy0: <TDK 78Q2120 media interface> on miibus0
tdkphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
found-> vendor=0x115d, dev=0x0103, revid=0x03
class=07-00-02, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=255
Product version: 5.0
Product name: Xircom | CardBus Ethernet 10/100 + Modem 56 | CBEM56G | 1.03
|
Manufacturer ID: 0501001081
Functions: Serial Port, Multi-Functioned
Function Extension: 00020f5c
Function Extension: 0206003f1c03030f070001b5
Function Extension: 1306000b000200b5
cardbus0: Opening BAR: type=IO, bar=10, len=0002
cardbus0: Opening BAR: type=MEM, bar=14, len=0002
cardbus0: Opening BAR: type=MEM, bar=18, len=0100
cardbus0: Invalid BAR number: 27(06)
CIS reading done
cardbus0: Non-prefetchable memory at 88002200-88002301
cardbus0: Non-prefetchable memory rid=18 at 88002200-880022ff (100)
cardbus0: Non-prefetchable memory rid=14 at 88002300-88002301 (2)
cardbus0: IO port at 1080-1081
cardbus0: IO port rid=10 at 1080-1081
cardbus0: <unknown card> (vendor=0x115d, dev=0x0103) at 0.1 irq 11
ata1-slave: timeout waiting for interrupt
ata1-slave: ATAPI identify failed
ad0: 13481MB <IBM-DCYA-214000> [27390/16/63] at ata0-master UDMA33
acd0: DVD-ROM <TOSHIBA DVD-ROM SD-C2102> at ata1-master PIO4
Mounting root from ufs:/dev/ad0s1a
OUTPUT OF SCANPCI -v:
=====================
pci bus 0x0000 cardnum 0x00 function 0x00: vendor 0x8086 device 0x7192
Intel 82443BX Host (no AGP)
CardVendor 0x1179 card 0x0001 (Toshiba 4010CDT CT65555)
STATUS 0xa200 COMMAND 0x0006
CLASS 0x06 0x00 0x00 REVISION 0x03
BIST 0x00 HEADER 0x00 LATENCY 0x40 CACHE 0x00
BASE0 0xe0000008 addr 0xe0000000 MEM PREFETCHABLE
pci bus 0x0000 cardnum 0x04 function 0x00: vendor 0x10c8 device 0x0005
Neomagic NM2200
CardVendor 0x1179 card 0x0001 (Toshiba 4010CDT CT65555)
STATUS 0x0290 COMMAND 0x0007
CLASS 0x03 0x00 0x00 REVISION 0x12
BIST 0x00 HEADER 0x00 LATENCY 0x40 CACHE 0x00
BASE0 0xdf000008 addr 0xdf000000 MEM PREFETCHABLE
BASE1 0xff800000 addr 0xff800000 MEM
BASE2 0xff700000 addr 0xff700000 MEM
MAX_LAT 0xff MIN_GNT 0x10 INT_PIN 0x01 INT_LINE 0x0b
pci bus 0x0000 cardnum 0x05 function 0x00: vendor 0x8086 device 0x7110
Intel 82371AB PIIX4 ISA
STATUS 0x0280 COMMAND 0x000f
CLASS 0x06 0x80 0x00 REVISION 0x02
BIST 0x00 HEADER 0x80 LATENCY 0x00 CACHE 0x00
pci bus 0x0000 cardnum 0x05 function 0x01: vendor 0x8086 device 0x7111
Intel 82371AB PIIX4 IDE
STATUS 0x0280 COMMAND 0x0005
CLASS 0x01 0x01 0x80 REVISION 0x01
BIST 0x00 HEADER 0x00 LATENCY 0x40 CACHE 0x00
BASE4 0x0000fe61 addr 0x0000fe60 I/O
BYTE_0 0xa303a307 BYTE_1 0x00 BYTE_2 0x00 BYTE_3 0x00
pci bus 0x0000 cardnum 0x05 function 0x02: vendor 0x8086 device 0x7112
Intel 82371AB PIIX4 USB
STATUS 0x0280 COMMAND 0x0005
CLASS 0x0c 0x03 0x00 REVISION 0x01
BIST 0x00 HEADER 0x00 LATENCY 0x40 CACHE 0x00
BASE4 0x0000ffe1 addr 0x0000ffe0 I/O
MAX_LAT 0x00 MIN_GNT 0x00 INT_PIN 0x04 INT_LINE 0x0b
pci bus 0x0000 cardnum 0x05 function 0x03: vendor 0x8086 device 0x7113
Intel 82371AB PIIX4 ACPI
STATUS 0x0280 COMMAND 0x0003
CLASS 0x06 0x80 0x00 REVISION 0x02
BYTE_0 0xfe01 BYTE_1 0x00 BYTE_2 0x00 BYTE_3 0x00
pci bus 0x0000 cardnum 0x09 function 0x00: vendor 0x1179 device 0x0701
Toshiba Device unknown
CardVendor 0x1179 card 0x0001 (Toshiba 4010CDT CT65555)
STATUS 0x0400 COMMAND 0x0005
CLASS 0x07 0x80 0x00 REVISION 0x23
BIST 0x00 HEADER 0x00 LATENCY 0x40 CACHE 0x00
BASE0 0x0000ff81 addr 0x0000ff80 I/O
MAX_LAT 0x00 MIN_GNT 0x00 INT_PIN 0x01 INT_LINE 0x0b
BYTE_0 0xb70200a0 BYTE_1 0x00 BYTE_2 0x00 BYTE_3 0x00
pci bus 0x0000 cardnum 0x0b function 0x00: vendor 0x1179 device 0x060f
Toshiba Device unknown
STATUS 0x0480 COMMAND 0x0007
CLASS 0x06 0x07 0x00 REVISION 0x05
BIST 0x00 HEADER 0x82 LATENCY 0x00 CACHE 0x00
BASE0 0x88000000 addr 0x88000000 MEM
BASE1 0x24800000 addr 0x24800000 MEM
BASE2 0x00141400 addr 0x00141400 MEM
BASE3 0xfffff000 addr 0xfffff000 MEM
BASE5 0xfffff000 addr 0xfffff000 MEM
BASEROM 0x0000107c addr 0x00000000 not-decode-enabled
MAX_LAT 0x07 MIN_GNT 0x00 INT_PIN 0x01 INT_LINE 0x0b
BYTE_0 0x11179 BYTE_1 0x00 BYTE_2 0x00 BYTE_3 0x00
pci bus 0x0000 cardnum 0x0b function 0x01: vendor 0x1179 device 0x060f
Toshiba Device unknown
STATUS 0x0480 COMMAND 0x0007
CLASS 0x06 0x07 0x00 REVISION 0x05
BIST 0x00 HEADER 0x82 LATENCY 0x00 CACHE 0x00
BASE0 0x88001000 addr 0x88001000 MEM
BASE1 0x04800000 addr 0x04800000 MEM
BASE2 0x00151500 addr 0x00151500 MEM
BASE3 0xfffff000 addr 0xfffff000 MEM
BASE5 0xfffff000 addr 0xfffff000 MEM
MAX_LAT 0x04 MIN_GNT 0x00 INT_PIN 0x02 INT_LINE 0x0b
BYTE_0 0x11179 BYTE_1 0x00 BYTE_2 0x00 BYTE_3 0x00
pci bus 0x0000 cardnum 0x0d function 0x00: vendor 0x123f device 0x8888
Device unknown
CardVendor 0x123f card 0x8888 (Card unknown)
STATUS 0x0210 COMMAND 0x0005
CLASS 0x04 0x80 0x00 REVISION 0x02
BIST 0x00 HEADER 0x00 LATENCY 0x40 CACHE 0x00
BASE0 0x0000ee01 addr 0x0000ee00 I/O
MAX_LAT 0x80 MIN_GNT 0x04 INT_PIN 0x01 INT_LINE 0x0b
BYTE_0 0x02 BYTE_1 0x00 BYTE_2 0x00 BYTE_3 0x00
pci bus 0x0014 cardnum 0x00 function 0x00: vendor 0x115d device 0x0003
Device unknown
CardVendor 0x115d card 0x1181 (Card unknown)
STATUS 0x0210 COMMAND 0x0007
CLASS 0x02 0x00 0x00 REVISION 0x03
BIST 0x00 HEADER 0x80 LATENCY 0xa8 CACHE 0x08
BASE0 0x00001001 addr 0x00001000 I/O
BASE1 0x88002000 addr 0x88002000 MEM
BASE2 0x88002000 addr 0x88002000 MEM
MAX_LAT 0x28 MIN_GNT 0x14 INT_PIN 0x01 INT_LINE 0x0b
pci bus 0x0014 cardnum 0x00 function 0x01: vendor 0x115d device 0x0103
Device unknown
CardVendor 0x115d card 0x1181 (Card unknown)
STATUS 0x0210 COMMAND 0x0001
CLASS 0x07 0x00 0x02 REVISION 0x03
BIST 0x00 HEADER 0x80 LATENCY 0x00 CACHE 0x00
BASE0 0x00000001 addr 0x00000000 I/O
MAX_LAT 0x00 MIN_GNT 0x00 INT_PIN 0x01 INT_LINE 0x0b
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-mobile" in the body of the message
help
Want to link to this message? Use this
URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?3E732BBD.8080907>