Date: Fri, 20 Jan 2012 08:31:34 -0800 From: Dennis Glatting <dg@pki2.com> To: Jeremy Chadwick <freebsd@jdc.parodius.com> Cc: freebsd-fs@freebsd.org Subject: Re: sanity check: is 9211-8i, on 8.3, with IT firmware still "the one" Message-ID: <1327077094.29408.11.camel@btw.pki2.com> In-Reply-To: <20120120153129.GA97746@icarus.home.lan> References: <alpine.BSF.2.00.1201191604510.19710@kozubik.com> <4F192ADA.5020903@brockmann-consult.de> <1327069331.29444.4.camel@btw.pki2.com> <20120120153129.GA97746@icarus.home.lan>
next in thread | previous in thread | raw e-mail | index | archive | help
On Fri, 2012-01-20 at 07:31 -0800, Jeremy Chadwick wrote: > On Fri, Jan 20, 2012 at 06:22:11AM -0800, Dennis Glatting wrote: > > I am having a problem with Seagate ST1000DL002 disks but I haven't yet > > determined weather it is the disks themselves (they -- two of them, new > > -- fail under a MB controller too. > > Assuming the disks are seen directly on the bus (e.g. show up as daX, > adaX, or whatever), please install ports/sysutils/smartmontools (make > sure you're using version 5.42 or newer) and please provide output from > the following command: "smartctl -a /dev/XXX" where XXX is the device > name of the ST1000DL002 disk(s). Please be sure to state which device > name is associated with which smartctl output. You can delete or > remove the disk serial numbers from the output (for privacy) if you > wish. I'll be happy to review the data and tell you whether or not the > disks themselves are showing problems or if the issue is elsewhere. > That is the motivation I needed to reboot that system, which was 50% through a task. That said, as remains the case today, for the last 20 years I haven't been able to find that "Any Key" on reboot. :) Regardless... The problematic disk from dmesg: da12 at mps2 bus 0 scbus4 target 5 lun 0 da12: <ATA ST1000DL002-9TT1 CC32> Fixed Direct Access SCSI-6 device da12: 300.000MB/s transfers da12: Command Queueing enabled da12: 953869MB (1953525168 512 byte sectors: 255H 63S/T 121601C) An attempt to write to it: bd3# dd if=/dev/zero of=/dev/da12 dd: /dev/da12: Input/output error 1+0 records in 0+0 records out 0 bytes transferred in 0.378153 secs (0 bytes/sec) The disk is presently connected to this device (LSI 9211-8i) but I have also had it connected to the devices on the MB and I think to a SuperMicro board. I have also tried a different LSI board. bd3# dmesg | grep mps2 mps2: <LSI SAS2008> port 0x8e00-0x8eff mem 0xfdcfc000-0xfdcfffff,0xfdc80000-0xfdcbffff irq 16 at device 0.0 on pci6 mps2: Firmware: 12.00.00.00 mps2: IOCCapabilities: 1285c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,EventReplay,HostDisc> The system is: bd3# uname -a FreeBSD bd3 9.0-STABLE FreeBSD 9.0-STABLE #1: Tue Jan 10 22:34:53 PST 2012 root@bd3:/sys/amd64/compile/BULLDOZER amd64 Full dmesg at the end. Note the errors with da12. And your request: bd3# smartctl -a /dev/da12 smartctl 5.42 2011-10-20 r3458 [FreeBSD 9.0-STABLE amd64] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Seagate Barracuda Green (Adv. Format) Device Model: ST1000DL002-9TT153 Serial Number: W1V06SLR LU WWN Device Id: 5 000c50 037e11be9 Firmware Version: CC32 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 4 Local Time is: Fri Jan 20 08:22:34 2012 PST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 612) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 169) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x30b7) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 108 099 006 Pre-fail Always - 241488 3 Spin_Up_Time 0x0003 087 070 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 28 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 100 253 030 Pre-fail Always - 136324 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 576 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 29 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 073 062 045 Old_age Always - 27 (Min/Max 21/27) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 23 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 29 194 Temperature_Celsius 0x0022 027 040 000 Old_age Always - 27 (0 21 0 0 0) 195 Hardware_ECC_Recovered 0x001a 027 008 000 Old_age Always - 241488 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 265544943010369 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 3746932548 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 3212957483 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 309 - # 2 Short offline Completed without error 00% 285 - # 3 Short offline Completed without error 00% 261 - # 4 Extended offline Completed without error 00% 258 - # 5 Short offline Completed without error 00% 237 - # 6 Short offline Completed without error 00% 213 - # 7 Short offline Completed without error 00% 189 - # 8 Short offline Completed without error 00% 175 - # 9 Short offline Completed without error 00% 151 - #10 Short offline Completed without error 00% 127 - #11 Short offline Completed without error 00% 103 - #12 Short offline Completed without error 00% 79 - #13 Short offline Completed without error 00% 55 - #14 Short offline Completed without error 00% 31 - #15 Short offline Completed without error 00% 7 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. bd3# dmesg Copyright (c) 1992-2012 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 9.0-STABLE #1: Tue Jan 10 22:34:53 PST 2012 root@bd3:/sys/amd64/compile/BULLDOZER amd64 CPU: AMD FX(tm)-8150 Eight-Core Processor (4017.98-MHz K8-class CPU) Origin = "AuthenticAMD" Id = 0x600f12 Family = 15 Model = 1 Stepping = 2 Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT> Features2=0x1698220b<SSE3,PCLMULQDQ,MON,SSSE3,CX16,SSE4.1,SSE4.2,POPCNT,AESNI,XSAVE,AVX> AMD Features=0x2e500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM> AMD Features2=0x1c9bfff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,OSVW,IBS,XOP,SKINIT,WDT,LWP,FMA4,NodeId,Topology,<b23>,<b24>> TSC: P-state invariant, performance statistics real memory = 17179869184 (16384 MB) avail memory = 16507908096 (15743 MB) Event timer "LAPIC" quality 400 ACPI APIC Table: <GBT GBTUACPI> FreeBSD/SMP: Multiprocessor System Detected: 8 CPUs FreeBSD/SMP: 1 package(s) x 8 core(s) cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 cpu2 (AP): APIC ID: 2 cpu3 (AP): APIC ID: 3 cpu4 (AP): APIC ID: 4 cpu5 (AP): APIC ID: 5 cpu6 (AP): APIC ID: 6 cpu7 (AP): APIC ID: 7 ioapic0: Changing APIC ID to 8 ioapic0 <Version 2.1> irqs 0-23 on motherboard kbd1 at kbdmux0 acpi0: <GBT GBTUACPI> on motherboard acpi0: Power Button (fixed) acpi0: reservation of 0, a0000 (3) failed acpi0: reservation of 100000, cfca0000 (3) failed Timecounter "ACPI-safe" frequency 3579545 Hz quality 850 acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 cpu0: <ACPI CPU> on acpi0 cpu1: <ACPI CPU> on acpi0 cpu2: <ACPI CPU> on acpi0 cpu3: <ACPI CPU> on acpi0 cpu4: <ACPI CPU> on acpi0 cpu5: <ACPI CPU> on acpi0 cpu6: <ACPI CPU> on acpi0 cpu7: <ACPI CPU> on acpi0 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pci0: <base peripheral> at device 0.2 (no driver attached) pcib1: <ACPI PCI-PCI bridge> irq 19 at device 3.0 on pci0 pci1: <ACPI PCI bus> on pcib1 mps0: <LSI SAS2008> port 0xde00-0xdeff mem 0xfd9fc000-0xfd9fffff,0xfd980000-0xfd9bffff irq 19 at device 0.0 on pci1 mps0: Firmware: 12.00.00.00 mps0: IOCCapabilities: 1285c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,EventReplay,HostDisc> pcib2: <ACPI PCI-PCI bridge> irq 16 at device 4.0 on pci0 pci2: <ACPI PCI bus> on pcib2 em0: <Intel(R) PRO/1000 Network Connection 7.2.3> port 0xcf00-0xcf1f mem 0xfd7c0000-0xfd7dffff,0xfd700000-0xfd77ffff,0xfd7fc000-0xfd7fffff irq 16 at device 0.0 on pci2 em0: Using MSIX interrupts with 3 vectors em0: Ethernet address: 00:1b:21:c6:d2:a0 pcib3: <ACPI PCI-PCI bridge> irq 17 at device 9.0 on pci0 pci3: <ACPI PCI bus> on pcib3 xhci0: <XHCI (generic) USB 3.0 controller> mem 0xfd5f8000-0xfd5fffff irq 17 at device 0.0 on pci3 xhci0: 64 byte context size. usbus0 on xhci0 pcib4: <ACPI PCI-PCI bridge> irq 18 at device 10.0 on pci0 pci4: <ACPI PCI bus> on pcib4 atapci0: <Marvell ATA controller> port 0xaf00-0xaf07,0xae00-0xae03,0xad00-0xad07,0xac00-0xac03,0xab00-0xab0f mem 0xfcbff000-0xfcbff1ff irq 18 at device 0.0 on pci4 ata2: <ATA channel> at channel 0 on atapci0 ata3: <ATA channel> at channel 1 on atapci0 pcib5: <ACPI PCI-PCI bridge> irq 19 at device 11.0 on pci0 pci5: <ACPI PCI bus> on pcib5 mps1: <LSI SAS2008> port 0x9e00-0x9eff mem 0xfdefc000-0xfdefffff,0xfde80000-0xfdebffff irq 19 at device 0.0 on pci5 mps1: Firmware: 12.00.00.00 mps1: IOCCapabilities: 185c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,IR> pcib6: <ACPI PCI-PCI bridge> irq 16 at device 12.0 on pci0 pci6: <ACPI PCI bus> on pcib6 mps2: <LSI SAS2008> port 0x8e00-0x8eff mem 0xfdcfc000-0xfdcfffff,0xfdc80000-0xfdcbffff irq 16 at device 0.0 on pci6 mps2: Firmware: 12.00.00.00 mps2: IOCCapabilities: 1285c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,EventReplay,HostDisc> pcib7: <ACPI PCI-PCI bridge> irq 17 at device 13.0 on pci0 pci7: <ACPI PCI bus> on pcib7 vgapci0: <VGA-compatible display> port 0xee00-0xeeff mem 0xd0000000-0xdfffffff,0xfdac0000-0xfdadffff irq 17 at device 0.0 on pci7 hdac0: <ATI (Unknown) High Definition Audio Controller> mem 0xfdafc000-0xfdafffff irq 18 at device 0.1 on pci7 ahci0: <ATI IXP700 AHCI SATA controller> port 0xff00-0xff07,0xfe00-0xfe03,0xfd00-0xfd07,0xfc00-0xfc03,0xfb00-0xfb0f mem 0xfdfff000-0xfdfff3ff irq 19 at device 17.0 on pci0 ahci0: AHCI v1.20 with 4 6Gbps ports, Port Multiplier supported ahcich0: <AHCI channel> at channel 0 on ahci0 ahcich1: <AHCI channel> at channel 1 on ahci0 ahcich2: <AHCI channel> at channel 2 on ahci0 ahcich3: <AHCI channel> at channel 3 on ahci0 ohci0: <OHCI (generic) USB controller> mem 0xfdffe000-0xfdffefff irq 18 at device 18.0 on pci0 usbus1: <OHCI (generic) USB controller> on ohci0 ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfdffd000-0xfdffd0ff irq 17 at device 18.2 on pci0 usbus2: EHCI version 1.0 usbus2: <EHCI (generic) USB 2.0 controller> on ehci0 ohci1: <OHCI (generic) USB controller> mem 0xfdffc000-0xfdffcfff irq 18 at device 19.0 on pci0 usbus3: <OHCI (generic) USB controller> on ohci1 ehci1: <EHCI (generic) USB 2.0 controller> mem 0xfdffb000-0xfdffb0ff irq 17 at device 19.2 on pci0 usbus4: EHCI version 1.0 usbus4: <EHCI (generic) USB 2.0 controller> on ehci1 pci0: <serial bus, SMBus> at device 20.0 (no driver attached) atapci1: <ATI IXP700/800 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfa00-0xfa0f at device 20.1 on pci0 ata0: <ATA channel> at channel 0 on atapci1 ata1: <ATA channel> at channel 1 on atapci1 isab0: <PCI-ISA bridge> at device 20.3 on pci0 isa0: <ISA bus> on isab0 pcib8: <ACPI PCI-PCI bridge> at device 20.4 on pci0 pci8: <ACPI PCI bus> on pcib8 ohci2: <OHCI (generic) USB controller> mem 0xfdffa000-0xfdffafff irq 18 at device 20.5 on pci0 usbus5: <OHCI (generic) USB controller> on ohci2 pcib9: <ACPI PCI-PCI bridge> at device 21.0 on pci0 pci9: <ACPI PCI bus> on pcib9 re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F PCIe Gigabit Ethernet> port 0x6e00-0x6eff mem 0xfd0ff000-0xfd0fffff,0xfd0f8000-0xfd0fbfff irq 17 at device 0.0 on pci9 re0: Using 1 MSI-X message re0: Chip rev. 0x2c800000 re0: MAC rev. 0x00000000 miibus0: <MII bus> on re0 rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus0 rgephy0: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow re0: Ethernet address: 50:e5:49:45:55:8e pcib10: <ACPI PCI-PCI bridge> at device 21.1 on pci0 pci10: <ACPI PCI bus> on pcib10 xhci1: <XHCI (generic) USB 3.0 controller> mem 0xfcff8000-0xfcffffff irq 17 at device 0.0 on pci10 xhci1: 64 byte context size. usbus6 on xhci1 pcib11: <ACPI PCI-PCI bridge> at device 21.2 on pci0 pci11: <ACPI PCI bus> on pcib11 atapci2: <Marvell ATA controller> port 0x3f00-0x3f07,0x3e00-0x3e03,0x3d00-0x3d07,0x3c00-0x3c03,0x3b00-0x3b0f mem 0xfcdff000-0xfcdff1ff irq 17 at device 0.0 on pci11 ata4: <ATA channel> at channel 0 on atapci2 ata5: <ATA channel> at channel 1 on atapci2 ohci3: <OHCI (generic) USB controller> mem 0xfdff9000-0xfdff9fff irq 18 at device 22.0 on pci0 usbus7: <OHCI (generic) USB controller> on ohci3 ehci2: <EHCI (generic) USB 2.0 controller> mem 0xfdff8000-0xfdff80ff irq 17 at device 22.2 on pci0 usbus8: EHCI version 1.0 usbus8: <EHCI (generic) USB 2.0 controller> on ehci2 attimer0: <AT timer> port 0x40-0x43 on acpi0 Timecounter "i8254" frequency 1193182 Hz quality 0 Event timer "i8254" frequency 1193182 Hz quality 100 hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff irq 0,8 on acpi0 Timecounter "HPET" frequency 14318180 Hz quality 950 atrtc0: <AT realtime clock> port 0x70-0x73 on acpi0 Event timer "RTC" frequency 32768 Hz quality 0 orm0: <ISA Option ROMs> at iomem 0xc0000-0xcffff,0xd0000-0xd5fff,0xd6000-0xd6fff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] ppc0: cannot reserve I/O port range hwpstate0: <Cool`n'Quiet 2.0> on cpu0 Timecounters tick every 1.000 msec hdac0: HDA Codec #0: ATI R6xx HDMI pcm0: <HDA ATI R6xx HDMI PCM #0 HDMI> at cad 0 nid 1 on hdac0 usbus0: 5.0Gbps Super Speed USB v3.0 usbus1: 12Mbps Full Speed USB v1.0 usbus2: 480Mbps High Speed USB v2.0 usbus3: 12Mbps Full Speed USB v1.0 usbus4: 480Mbps High Speed USB v2.0 usbus5: 12Mbps Full Speed USB v1.0 usbus6: 5.0Gbps Super Speed USB v3.0 usbus7: 12Mbps Full Speed USB v1.0 usbus8: 480Mbps High Speed USB v2.0 ugen0.1: <0x1b6f> at usbus0 uhub0: <0x1b6f XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0 ugen1.1: <ATI> at usbus1 uhub1: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1 ugen2.1: <ATI> at usbus2 uhub2: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2 ugen3.1: <ATI> at usbus3 uhub3: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3 ugen4.1: <ATI> at usbus4 uhub4: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus4 ugen5.1: <ATI> at usbus5 uhub5: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5 ugen6.1: <0x1b6f> at usbus6 uhub6: <0x1b6f XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus6 ugen7.1: <ATI> at usbus7 uhub7: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus7 ugen8.1: <ATI> at usbus8 uhub8: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus8 uhub5: 2 ports with 2 removable, self powered uhub7: 4 ports with 4 removable, self powered uhub1: 5 ports with 5 removable, self powered uhub3: 5 ports with 5 removable, self powered uhub0: 4 ports with 4 removable, self powered uhub6: 4 ports with 4 removable, self powered uhub8: 4 ports with 4 removable, self powered uhub2: 5 ports with 5 removable, self powered uhub4: 5 ports with 5 removable, self powered ugen1.2: <BTC> at usbus1 ukbd0: <BTC USB Multimedia Keyboard, class 0/0, rev 1.10/1.00, addr 2> on usbus1 kbd2 at ukbd0 uhid0: <BTC USB Multimedia Keyboard, class 0/0, rev 1.10/1.00, addr 2> on usbus1 ada0 at ahcich0 bus 0 scbus5 target 0 lun 0 ada0: <Corsair Force 3 SSD 1.3.3> ATA-8 SATA 3.x device ada0: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes) ada0: Command Queueing enabled ada0: 85857MB (175836528 512 byte sectors: 16H 63S/T 16383C) ada0: Previously was known as ad8 ada1 at ahcich1 bus 0 scbus6 target 0 lun 0 ada1: <OCZ-AGILITY2 1.33> ATA-8 SATA 2.x device ada1: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes) ada1: Command Queueing enabled ada1: 57241MB (117231408 512 byte sectors: 16H 63S/T 16383C) ada1: Previously was known as ad10 ada2 at ahcich2 bus 0 scbus7 target 0 lun 0 ada2: <ST31000333AS SD35> ATA-8 SATA 2.x device ada2: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes) ada2: Command Queueing enabled ada2: 953869MB (1953525168 512 byte sectors: 16H 63S/T 16383C) ada2: Previously was known as ad12 da12 at mps2 bus 0 scbus4 target 5 lun 0 da12: <ATA ST1000DL002-9TT1 CC32> Fixed Direct Access SCSI-6 device da12: 300.000MB/s transfers da12: Command Queueing enabled da12: 953869MB (1953525168 512 byte sectors: 255H 63S/T 121601C) SMP: AP CPU #2 Launched! da7 at mps0 bus 0 scbus0 target 7 lun 0 da7: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device da7: 300.000MB/s transfers da7: Command Queueing enabled da7: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C) da3 at mps0 bus 0 scbus0 target 3 lun 0 da3: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device da3: 300.000MB/s transfers da3: Command Queueing enabled da3: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C) da0 at mps0 bus 0 scbus0 target 0 lun 0 da0: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device da0: 300.000MB/s transfers da0: Command Queueing enabled da0: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C) SMP: AP CPU #4 Launched! da6 at mps0 bus 0 scbus0 target 6 lun 0 da6: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device da6: 300.000MB/s transfers da6: Command Queueing enabled da6: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C) da5 at mps0 bus 0 scbus0 target 5 lun 0 da5: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device da5: 300.000MB/s transfers da5: Command Queueing enabled da5: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C) da4 at mps0 bus 0 scbus0 target 4 lun 0 da4: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device da4: 300.000MB/s transfers da4: Command Queueing enabled da4: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C) SMP: AP CPU #6 Launched! da9 at mps2 bus 0 scbus4 target 1 lun 0 da9: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device da9: 300.000MB/s transfers da9: Command Queueing enabled da9: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C) da10 at mps2 bus 0 scbus4 target 2 lun 0 da10: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device da10: 300.000MB/s transfers da10: Command Queueing enabled da10: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C) da8 at mps2 bus 0 scbus4 target 0 lun 0 da8: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device da8: 300.000MB/s transfers da8: Command Queueing enabled da8: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C) SMP: AP CPU #1 Launched! da11 at mps2 bus 0 scbus4 target 3 lun 0 da11: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device da11: 300.000MB/s transfers da11: Command Queueing enabled da11: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C) da1 at mps0 bus 0 scbus0 target 1 lun 0 da1: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device da1: 300.000MB/s transfers da1: Command Queueing enabled da1: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C) da2 at mps0 bus 0 scbus0 target 2 lun 0 da2: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device da2: 300.000MB/s transfers da2: Command Queueing enabled da2: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C) SMP: AP CPU #3 Launched! SMP: AP CPU #5 Launched! SMP: AP CPU #7 Launched! Timecounter "TSC-low" frequency 15695219 Hz quality 1000 (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 1 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 1 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 1 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 1 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 1 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): SYNCHRONIZE CACHE(10). CDB: 35 0 0 0 0 0 0 0 0 0 (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(10). CDB: 28 0 74 70 6d af 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(10). CDB: 28 0 74 70 6d af 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(10). CDB: 28 0 74 70 6d af 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(10). CDB: 28 0 74 70 6d af 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(10). CDB: 28 0 74 70 6d af 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 40 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 40 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 40 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 40 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 40 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 2 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 2 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 2 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 2 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 2 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): SYNCHRONIZE CACHE(10). CDB: 35 0 0 0 0 0 0 0 0 0 (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): SYNCHRONIZE CACHE(10). CDB: 35 0 0 0 0 0 0 0 0 0 (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) Trying to mount root from ufs:/dev/gpt/disk0 [rw]... ZFS filesystem version 5 ZFS storage pool version 28 (da12:mps2:0:5:0): WRITE(6). CDB: a 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): WRITE(6). CDB: a 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): WRITE(6). CDB: a 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): WRITE(6). CDB: a 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): WRITE(6). CDB: a 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): SYNCHRONIZE CACHE(10). CDB: 35 0 0 0 0 0 0 0 0 0 (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 1 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 1 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 1 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 1 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 1 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): SYNCHRONIZE CACHE(10). CDB: 35 0 0 0 0 0 0 0 0 0 (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(10). CDB: 28 0 74 70 6d af 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(10). CDB: 28 0 74 70 6d af 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(10). CDB: 28 0 74 70 6d af 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(10). CDB: 28 0 74 70 6d af 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(10). CDB: 28 0 74 70 6d af 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 2 0 10 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 40 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 40 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 40 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 40 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 40 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 2 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 2 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 2 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 2 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 2 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 10 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 80 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): READ(6). CDB: 8 0 0 0 1 0 (da12:mps2:0:5:0): CAM status: SCSI Status Error (da12:mps2:0:5:0): SCSI status: Check Condition (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) (da12:mps2:0:5:0): SYNCHRONIZE CACHE(10). CDB: 35 0 0 0 0 0 0 0 0 0 (da12:mps2:0:5:0): SCSI sense: ABORTED COMMAND asc:0,0 (No additional sense information) -- Dennis Glatting <dg@pki2.com>
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?1327077094.29408.11.camel>