Date: Wed, 11 Sep 2002 14:40:55 -0400 From: "Neil Bahroos" <doooks@hotmail.com> To: <freebsd-smp@freebsd.org> Cc: <doc@freebsd.org>, <freebsd-questions@freebsd.org> Subject: SMPng with FreeBSD 4.6.2 with USB Message-ID: <OE42Q4ZLsluP1q0cTKF00004e87@hotmail.com>
next in thread | raw e-mail | index | archive | help
Hello freebsd.org, I am trying to run the SMP kernel on a Abit VP6 DUAL pIII (800MHZ). I have no problems booting and getting the system going if using ps/2 keyboard. If I happen to use a USB keyboard then the console goes haywire. I can still use this machine via the network by ssh'ing to it. I dont know if the problem is on my end, or you have just not tested the SMP kernel with USB keyboard setup. The USB keyboard I am using is a Microsoft IntelliKeyboard Pro, it has a 2 port USB hub built in, to which I connect my MS USB, intellimouse. I have commented out cpu i386, i486, and i586 as recommended in the LINT kernel file. My mptable output follows (done from GENERIC UP kernel) along with dmesg output. Thankyou, Neil Bahroos > mptable ============================================================================ === MPTable, version 2.0.15 ---------------------------------------------------------------------------- --- MP Floating Pointer Structure: location: BIOS physical address: 0x000f5700 signature: '_MP_' length: 16 bytes version: 1.4 checksum: 0x7d mode: Virtual Wire ---------------------------------------------------------------------------- --- MP Config Table Header: physical address: 0x000f1400 signature: 'PCMP' base table length: 292 version: 1.4 checksum: 0x2b OEM ID: 'OEM00000' Product ID: 'PROD00000000' OEM table pointer: 0x00000000 OEM table size: 0 entry count: 28 local APIC address: 0xfee00000 extended table length: 0 extended table checksum: 0 ---------------------------------------------------------------------------- --- MP Config Base Table Entries: -- Processors: APIC ID Version State Family Model Step Flags 0 0x11 BSP, usable 6 8 10 0xfbff 1 0x11 AP, usable 6 8 6 0xfbff -- Bus: Bus ID Type 0 PCI 1 PCI 2 ISA -- I/O APICs: APIC ID Version State Address 2 0x11 usable 0xfec00000 -- I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN# ExtINT conforms conforms 2 0 2 0 INT conforms conforms 2 1 2 1 INT conforms conforms 2 0 2 2 INT conforms conforms 2 3 2 3 INT conforms conforms 2 4 2 4 INT conforms conforms 2 6 2 6 INT conforms conforms 2 7 2 7 INT active-hi edge 2 8 2 8 INT conforms conforms 2 9 2 9 INT conforms conforms 2 13 2 13 INT conforms conforms 2 14 2 14 INT conforms conforms 2 15 2 15 INT active-lo level 0 7:D 2 19 INT active-lo level 0 7:D 2 19 INT active-lo level 0 10:A 2 17 INT active-lo level 0 12:A 2 19 INT active-lo level 0 13:A 2 18 INT active-lo level 0 14:A 2 18 INT active-lo level 1 0:A 2 16 SMI conforms conforms 2 0 2 23 -- Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN# ExtINT conforms conforms 0 0:A 255 0 NMI conforms conforms 0 0:A 255 1 ============================================================================ === > dmesg Copyright (c) 1992-2002 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 4.6.2-RELEASE #0: Wed Aug 14 21:23:26 GMT 2002 murray@builder.freebsdmall.com:/usr/src/sys/compile/GENERIC Timecounter "i8254" frequency 1193182 Hz CPU: Pentium III/Pentium III Xeon/Celeron (798.69-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x68a Stepping = 10 Features=0x387fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA, CMOV,PAT,PSE36,PN,MMX,FXSR,SSE> real memory = 536805376 (524224K bytes) avail memory = 517382144 (505256K bytes) Preloaded elf kernel "kernel" at 0xc04d0000. Pentium Pro MTRR support enabled md0: Malloc disk Using $PIR table, 8 entries at 0xc00fdbc0 npx0: <math processor> on motherboard npx0: INT 16 interface pcib0: <Host to PCI bridge> on motherboard pci0: <PCI bus> on pcib0 pcib1: <VIA 82C598MVP (Apollo MVP3) PCI-PCI (AGP) bridge> at device 1.0 on pci0 pci1: <PCI bus> on pcib1 pci1: <ATI model 5157 graphics accelerator> at 0.0 irq 12 isab0: <VIA 82C686 PCI-ISA bridge> at device 7.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <VIA 82C686 ATA100 controller> port 0xa000-0xa00f at device 7.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 uhci0: <VIA 83C572 USB controller> port 0xa400-0xa41f irq 10 at device 7.2 on pci0 usb0: <VIA 83C572 USB controller> on uhci0 usb0: USB revision 1.0 uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhub1: Texas Instruments TUSB2046 hub, class 9/0, rev 1.10/1.25, addr 2 uhub1: 4 ports with 4 removable, self powered ukbd0: ATEN 4 Port USB KVM B V1.30, rev 1.10/1.00, addr 3, iclass 3/1 kbd0 at ukbd0 ums0: ATEN 4 Port USB KVM B V1.30, rev 1.10/1.00, addr 3, iclass 3/1 ums0: 5 buttons and Z dir. uhci1: <VIA 83C572 USB controller> port 0xa800-0xa81f irq 10 at device 7.3 on pci0 usb1: <VIA 83C572 USB controller> on uhci1 usb1: USB revision 1.0 uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub2: 2 ports with 2 removable, self powered pci0: <unknown card> (vendor=0x1106, dev=0x3057) at 7.4 pci0: <unknown card> (vendor=0x1102, dev=0x0002) at 10.0 irq 5 pci0: <unknown card> (vendor=0x1102, dev=0x7002) at 10.1 sis0: <NatSemi DP83815 10/100BaseTX> port 0xb400-0xb4ff mem 0xdf000000-0xdf000fff irq 10 at device 12.0 on pci0 sis0: Ethernet address: 00:02:e3:22:20:ba miibus0: <MII bus> on sis0 ukphy0: <Generic IEEE 802.3u media interface> on miibus0 ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto sis1: <NatSemi DP83815 10/100BaseTX> port 0xb800-0xb8ff mem 0xdf001000-0xdf001fff irq 11 at device 13.0 on pci0 sis1: Ethernet address: 00:02:e3:22:20:c4 miibus1: <MII bus> on sis1 ukphy1: <Generic IEEE 802.3u media interface> on miibus1 ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto atapci1: <HighPoint HPT370 ATA100 controller> port 0xcc00-0xccff,0xc800-0xc803,0xc400-0xc407,0xc000-0xc003,0xbc00-0xbc07 irq 11 at device 14.0 on pci0 ata2: at 0xbc00 on atapci1 ata3: at 0xc400 on atapci1 orm0: <Option ROMs> at iomem 0xc0000-0xcbfff,0xcc000-0xcffff,0xd0000-0xd37ff on isa0 fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A sio1 at port 0x2f8-0x2ff irq 3 on isa0 sio1: type 16550A ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode plip0: <PLIP network interface> on ppbus0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 ar0: 78167MB <ATA RAID0 array> [9964/255/63] status: READY subdisks: 0 READY ad4: 39083MB <Maxtor 5T040H4> [79408/16/63] at ata2-master UDMA100 1 READY ad5: 39083MB <Maxtor 5T040H4> [79408/16/63] at ata2-slave UDMA100 ar1: 76324MB <ATA RAID0 array> [9729/255/63] status: READY subdisks: 0 READY ad6: 38162MB <Maxtor 5T040H4> [77536/16/63] at ata3-master UDMA100 1 READY ad7: 39083MB <Maxtor 5T040H4> [79408/16/63] at ata3-slave UDMA100 acd0: DVD-ROM <Pioneer DVD-ROM ATAPIModel DVD-115 0122> at ata0-master PIO4 acd1: CD-RW <HL-DT-ST CD-RW GCE-8240B> at ata0-slave PIO4 Mounting root from ufs:/dev/ar0s1a To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-smp" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?OE42Q4ZLsluP1q0cTKF00004e87>