Date: Tue, 09 Aug 2005 02:43:49 +0200 From: sp4rc <sammyshome@gmx.net> To: freebsd-alpha@freebsd.org Subject: Re: AS1200 Question Message-ID: <1123548229.16459.32.camel@uranos.pentacon.gov> In-Reply-To: <20050808231206.GB94041@cicely12.cicely.de> References: <1123540691.16459.1.camel@uranos.pentacon.gov> <20050808231206.GB94041@cicely12.cicely.de>
next in thread | previous in thread | raw e-mail | index | archive | help
> > has anyone been able to install FreeBSd 5.4 on a Alpha Server 1200? The
> > bootprocess from cd hangs.
>
> An AS1200 should run just fine.
> At which point does it hang?
> Complete boot messages would be great.
oh, sorry for that, after 17h infront of my terminal i became a bit
forgetfully.
P00>>>boot dka500
Initializing...
SROM V3.0 on cpu0
XSROM V6.0 on cpu0
BCache testing complete on cpu0
mem_pair0 - 256 MB
mem_pair1 - 256 MB
mem_pair2 - 256 MB
mem_pair3 - 256 MB
mem_pair4 - 256 MB
mem_pair5 - 256 MB
20..21..23..
please wait 54 seconds for T24 to complete
24..
Memory testing complete on cpu0
starting console on CPU 0
sizing memory
0 256 MB DIMM
1 256 MB DIMM
2 256 MB DIMM
3 256 MB DIMM
4 256 MB DIMM
5 256 MB DIMM
probing IOD1 hose 1
bus 0 slot 1 - NCR 53C810
bus 0 slot 4 - QLogic ISP10X0
probing IOD0 hose 0
PCI device in hose 0 slot 2 incorrectly decodes Type 1 configuration
cycles,
may interfere with subordinate PCI buses.
bus 0 slot 1 - PCEB
probing EISA Bridge, bus 1
bus 0 slot 2 - Digital 2T-PMPAA/Pixelwork
bus 0 slot 4 - DECchip 21140-AA
mouse test 4 failed
configuring I/O adapters...
ncr0, hose 1, bus 0, slot 1
isp0, hose 1, bus 0, slot 4
floppy0, hose 0, bus 1, slot 0
tulip0, hose 0, bus 0, slot 4
System temperature is 24 degrees C
AlphaServer 1200 Console V6.0-4, 10-MAY-2001 10:11:42
CPU 0 booting
(boot dka500.5.0.1.1 -flags a)
block 0 of dka500.5.0.1.1 is a valid boot block
reading 410 blocks from dka500.5.0.1.1
bootstrap code read in
Building FRU table
base = 200000, image_start = 0, image_bytes = 33400
initializing HWRPB at 2000
initializing page table at 1f2000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
Console: SRM firmware console
VMS PAL rev: 0x4000200010115
OSF PAL rev: 0x4000200020117
Switch to OSF PAL code succeeded.
FreeBSD/alpha SRM CD9660 boot, Revision 1.2
(root@ds10.freebie.xs4all.nl, Mon May 9 13:32:23 UTC 2005)
Memory: 1572864 k
Loading /boot/defaults/loader.conf
/boot/kernel/kernel data=0x5e8d60+0x3d720 syms=[0x8+0x669a8+0x8+0x54f0f]
\
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...
Entering /boot/kernel/kernel at 0xfffffc0000345de0...
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights
reserved.
FreeBSD 5.4-RELEASE #0: Mon May 9 21:18:39 UTC 2005
root@ds10.freebie.xs4all.nl:/usr/obj/usr/src/sys/GENERIC
never mind about the -a flag, i have also tried without it...
any hints would be greatly appreciated.
/sp4rc
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?1123548229.16459.32.camel>