Date: Tue, 23 Jul 2013 06:13:15 -0700 From: Adrian Chadd <adrian@freebsd.org> To: Andrey Fesenko <f0andrey@gmail.com> Cc: "freebsd-wireless@freebsd.org" <freebsd-wireless@freebsd.org>, freebsd-current <freebsd-current@freebsd.org> Subject: Re: Not work ATH (AR9285) after update Message-ID: <CAJ-Vmok_4ruA=GwJyR0=fB403WyLjTRbdZnN1YUZSA1bmTc0ng@mail.gmail.com> In-Reply-To: <CA%2BK5SrNv15gBOqHrRt2HnoohQkML7o0P5OJZ88XvMgZ=QfXiSw@mail.gmail.com> References: <CA%2BK5SrNv15gBOqHrRt2HnoohQkML7o0P5OJZ88XvMgZ=QfXiSw@mail.gmail.com>
next in thread | previous in thread | raw e-mail | index | archive | help
.. are two copies of wpa_supplicant running? -adrian On 23 July 2013 06:09, Andrey Fesenko <f0andrey@gmail.com> wrote: > Hello, > i'm horrible news, after update my notebook not nave wi-fi :( > full update system, build and install world and kernel. > > # uname -a > FreeBSD x220.local 10.0-CURRENT FreeBSD 10.0-CURRENT #0 r253562: Tue > Jul 23 14:44:07 MSK 2013 > root@x220.local:/usr/obj/usr/src/sys/W_BOOK amd64 > > # grep ATH /usr/src/sys/amd64/conf/W_BOOK > options ATH_ENABLE_11N > options ATH_DEBUG > options ATH_DIAGAPI > > ath0@pci0:3:0:0: class=0x028000 card=0x1a891a3b chip=0x002b168c > rev=0x01 hdr=0x00 > vendor = 'Atheros Communications Inc.' > device = 'AR9285 Wireless Network Adapter (PCI-Express)' > class = network > > # ifconfig > ath0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 2290 > ether 00:25:d3:7b:94:87 > nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL> > media: IEEE 802.11 Wireless Ethernet autoselect mode 11g > status: associated > wlan0: flags=8c43<UP,BROADCAST,RUNNING,OACTIVE,SIMPLEX,MULTICAST> > metric 0 mtu 1500 > ether 00:25:d3:7b:94:87 > inet6 fe80::225:d3ff:fe7b:9487%wlan0 prefixlen 64 scopeid 0x4 > nd6 options=23<PERFORMNUD,ACCEPT_RTADV,AUTO_LINKLOCAL> > media: IEEE 802.11 Wireless Ethernet autoselect (autoselect) > status: no carrier > ssid "" channel 8 (2447 MHz 11g) > regdomain 33411 country RU indoor ecm authmode WPA1+WPA2/802.11i > privacy MIXED deftxkey UNDEF txpower 20 bmiss 7 scanvalid 60 > protmode CTS wme burst roaming MANUAL > # ifconfig wlan0 list scan > SSID/MESH ID BSSID CHAN RATE S:N INT CAPS > APT-SPB2 b8:a3:86:4a:75:6a 6 54M -92:-96 100 EP HTCAP > WPA RSN WME WPS > THD1 74:ea:3a:d1:37:46 10 54M -85:-96 100 EP RSN HTCAP WME > Balt1 00:90:4c:c1:00:00 1 54M -90:-96 100 EP RSN > TP-LINK_904D2A 64:70:02:90:4d:2a 11 54M -94:-96 100 EPS RSN > HTCAP WME ATH WPS > > /var/log/messages > ... > Jul 23 15:34:24 x220 wpa_supplicant[669]: wlan0: CTRL-EVENT-TERMINATING > Jul 23 15:34:24 x220 kernel: wlan0: Ethernet address: 00:25:d3:7b:94:87 > Jul 23 15:34:24 x220 devd: Executing '/etc/pccard_ether wlan0 start' > Jul 23 15:34:24 x220 wpa_supplicant[2563]: Successfully initialized > wpa_supplicant > Jul 23 15:34:24 x220 wpa_supplicant[2571]: Successfully initialized > wpa_supplicant > Jul 23 15:34:24 x220 wpa_supplicant[2571]: ctrl_iface exists and seems > to be in use - cannot override it > Jul 23 15:34:24 x220 wpa_supplicant[2571]: Delete > '/var/run/wpa_supplicant/wlan0' manually if it is not used anymore > Jul 23 15:34:24 x220 wpa_supplicant[2571]: Failed to initialize > control interface '/var/run/wpa_supplicant'. You may have another > wpa_supplicant process already running or the file was left by an > unclean termination of wpa_supplicant in which case you will need to > manually remove this file before starting wpa_supplicant again. > Jul 23 15:34:24 x220 wpa_supplicant[2571]: ioctl[SIOCS80211, op=26, > val=0, arg_len=0]: Operation not supported > Jul 23 15:34:24 x220 wpa_supplicant[2571]: ioctl[SIOCS80211, op=26, > val=0, arg_len=0]: Operation not supported > Jul 23 15:34:24 x220 root: /etc/rc.d/wpa_supplicant: WARNING: failed > to start wpa_supplicant > Jul 23 15:34:24 x220 wpa_supplicant[2572]: ioctl[SIOCS80211, op=103, > val=0, arg_len=128]: Operation now in progress > Jul 23 15:34:24 x220 wpa_supplicant[2572]: wlan0: Failed to initiate AP scan > Jul 23 15:34:25 x220 wpa_supplicant[2572]: ioctl[SIOCS80211, op=103, > val=0, arg_len=128]: Operation now in progress > Jul 23 15:34:25 x220 wpa_supplicant[2572]: wlan0: Failed to initiate AP scan > Jul 23 15:34:26 x220 wpa_supplicant[2572]: ioctl[SIOCS80211, op=103, > val=0, arg_len=128]: Operation now in progress > Jul 23 15:34:26 x220 kernel: ath0: ath_reset_grablock: didn't finish > after 10 iterations > Jul 23 15:34:26 x220 kernel: ath0: ath_reset_grablock: warning, > recursive reset path! > Jul 23 15:34:26 x220 kernel: ath0: ath_reset: concurrent reset! Danger! > Jul 23 15:34:26 x220 kernel: ath0: ath_raw_xmit: sc_inreset_cnt > 0; bailing > Jul 23 15:34:26 x220 kernel: ath0: ath_raw_xmit: sc_inreset_cnt > 0; bailing > Jul 23 15:34:26 x220 wpa_supplicant[2572]: wlan0: Failed to initiate AP scan > Jul 23 15:34:27 x220 wpa_supplicant[2572]: ioctl[SIOCS80211, op=103, > val=0, arg_len=128]: Operation now in progress > Jul 23 15:34:27 x220 wpa_supplicant[2572]: wlan0: Failed to initiate AP scan > Jul 23 15:34:29 x220 wpa_supplicant[2572]: ioctl[SIOCS80211, op=103, > val=0, arg_len=128]: Operation now in progress > Jul 23 15:34:29 x220 kernel: ath0: ath_reset_grablock: didn't finish > after 10 iterations > Jul 23 15:34:29 x220 kernel: ath0: ath_reset_grablock: warning, > recursive reset path! > _______________________________________________ > freebsd-current@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-current > To unsubscribe, send any mail to "freebsd-current-unsubscribe@freebsd.org"
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?CAJ-Vmok_4ruA=GwJyR0=fB403WyLjTRbdZnN1YUZSA1bmTc0ng>