Date: Sat, 20 Nov 2004 01:05:44 -0500 (EST) From: allan@stokes.ca To: "freebsd-questions@freebsd.org" <freebsd-questions@freebsd.org> Subject: 5.3/AMD64 fails to detect ARAID-99 PATA unit when booting Tyan S2882 from a SATA unit Message-ID: <65514.142.179.103.195.1100930744.squirrel@142.179.103.195>
next in thread | raw e-mail | index | archive | help
Yesterday I received hardware to complete a Tyan S2882 based system. In
just a few hours I had FreeBSD 5.3-STABLE/AMD64 running with all memory
and processors accounted for.
I have two hotswap IDE RAID devices installed. I have an old ARAID-99
from the previous 4.x system where it worked fine. I have added a new
SOHORAID based on the same electronics, but with a SATA interface. Last
night I installed a test copy of FreeBSD 5.3 on the new SATA unit using
fresh drives.
Because the Tyan BIOS is weak concerning boot devices I had to go into a
screen and make the SATA controller the #1 IDE device and the PATA
controller the #2 drive. Then I was able to boot off the SATA image with
the PATA unit installed.
The BIOS screen detects the ARAID as the IDE primary master prior to the
SATA boot cycle. Then when FreeBSD boots, FreeBSD does not. There is no
/dev/ad0 as I expected. I've booted with blank drives in the ARAID and
with older FreeBSD 4.x drives installed.
fdisk / diskinfo / disklabel won't show me ad0. They all complain that
the device does not exist. I tried to fake it out with makenod but then I
got "device not configured". I'm not too strong on devfs yet and there is
presently no man page for devfs.conf
Is there some reason under 5.3 that booting off the SATA SOHORAID would
prevent the PATA RAID drive detect? The ARAID-99/1000 appears to FreeBSD
as a single PATA disk drive echoing the geometry of whatever primary drive
is presently inserted.
Is there a boot parameter to see additional diagnostics from the ATA drive
probe?
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.3-RELEASE #0: Fri Nov 5 03:50:01 UTC 2004
root@fanboy.samsco.home:/usr/obj/usr/src/sys/GENERIC
ACPI APIC Table: <A M I OEMAPIC >
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Opteron(tm) Processor 242 (1593.61-MHz K8-class CPU)
Origin = "AuthenticAMD" Id = 0xf5a Stepping = 10
Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2>
AMD Features=0xe0500800<SYSCALL,NX,MMX+,LM,3DNow+,3DNow>
real memory = 2147418112 (2047 MB)
avail memory = 2061897728 (1966 MB)
MADT: Forcing active-low polarity and level trigger for SCI
ioapic0 <Version 1.1> irqs 0-23 on motherboard
ioapic1 <Version 1.1> irqs 24-27 on motherboard
ioapic2 <Version 1.1> irqs 28-31 on motherboard
acpi0: <A M I OEMRSDT> on motherboard
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x5008-0x500b on acpi0
cpu0: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 6.0 on pci0
pci3: <ACPI PCI bus> on pcib1
ohci0: <OHCI (generic) USB controller> mem 0xfeafc000-0xfeafcfff irq 19 at
device 0.0 on pci3
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
ohci1: <OHCI (generic) USB controller> mem 0xfeafd000-0xfeafdfff irq 19 at
device 0.1 on pci3
ohci1: [GIANT-LOCKED]
usb1: OHCI version 1.0, legacy support
usb1: <OHCI (generic) USB controller> on ohci1
usb1: USB revision 1.0
uhub1: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 3 ports with 3 removable, self powered
atapci0: <SiI 3114 SATA150 controller> port
0xa800-0xa80f,0xac00-0xac03,0xb000-0xb007,0xb400-0xb403,0xbc00-0xbc07 mem
0xfeafec00-0xfeafefff irq 19 at device 5.0 on pci3
ata2: channel #0 on atapci0
ata3: channel #1 on atapci0
ata4: channel #2 on atapci0
ata5: channel #3 on atapci0
pci3: <display, VGA> at device 6.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci1: <AMD 8111 UDMA133 controller> port
0xffa0-0xffaf,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 7.1 on pci0
ata0: channel #0 on atapci1
ata1: channel #1 on atapci1
pci0: <serial bus, SMBus> at device 7.2 (no driver attached)
pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> at device 10.0 on pci0
pci2: <ACPI PCI bus> on pcib2
bge0: <Broadcom BCM5704C Dual Gigabit Ethernet, ASIC rev. 0x2003> mem
0xfc8b0000-0xfc8bffff,0xfc8c0000-0xfc8cffff irq 24 at device 9.0 on pci2
miibus0: <MII bus> on bge0
brgphy0: <BCM5704 10/100/1000baseTX PHY> on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
1000baseTX-FDX, auto
bge0: Ethernet address: 00:e0:81:2b:b6:86
bge1: <Broadcom BCM5704C Dual Gigabit Ethernet, ASIC rev. 0x2003> mem
0xfc8e0000-0xfc8effff,0xfc8f0000-0xfc8fffff irq 25 at device 9.1 on pci2
miibus1: <MII bus> on bge1
brgphy1: <BCM5704 10/100/1000baseTX PHY> on miibus1
brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
1000baseTX-FDX, auto
bge1: Ethernet address: 00:e0:81:2b:b6:87
pci0: <base peripheral, interrupt controller> at device 10.1 (no driver
attached)
pcib3: <ACPI PCI-PCI bridge> at device 11.0 on pci0
pci1: <ACPI PCI bus> on pcib3
pci0: <base peripheral, interrupt controller> at device 11.1 (no driver
attached)
acpi_button0: <Power Button> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
fdc0: <floppy drive controller (FDE)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2
on acpi0
fdc0: does not respond
device_attach: fdc0 attach returned 6
ppc0: <Standard parallel printer port> port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
fdc0: <floppy drive controller (FDE)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2
on acpi0
fdc0: does not respond
device_attach: fdc0 attach returned 6
orm0: <ISA Option ROMs> at iomem 0xc8000-0xcc7ff,0xc0000-0xc7fff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 1593614519 Hz quality 800
Timecounters tick every 0.976 msec
acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0%
ad4: 190782MB <SOHORAID SR2600 REV:0.91 Mirroring/Rev 0.91> [387621/16/63]
at ata2-master SATA150
Mounting root from ufs:/dev/ad4s1a
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?65514.142.179.103.195.1100930744.squirrel>