Date: Thu, 14 Nov 2002 15:53:35 +1100 From: Rob <rbyrnes@ozemail.com.au> To: John Baldwin <jhb@FreeBSD.org> Cc: freebsd-alpha@freebsd.org, Andrew Gallatin <gallatin@cs.duke.edu> Subject: Re: 5.0 alpha install tests Message-ID: <oprft47lvyzn6bwz@smtp.ozemail.com.au> References: <XFMail.20021109093904.jhb@FreeBSD.org>
next in thread | previous in thread | raw e-mail | index | archive | help
On Sat, 09 Nov 2002 09:39:04 -0500 (EST), John Baldwin <jhb@FreeBSD.org> wrote: > > On 09-Nov-2002 Rob B wrote: >> ----- Original Message ----- >> From: "Andrew Gallatin" <gallatin@cs.duke.edu> >> To: "Rob B" <rbyrnes@ozemail.com.au> >> Cc: <freebsd-alpha@FreeBSD.ORG> >> Sent: Thursday, November 07, 2002 1:44 PM >> Subject: Re: 5.0 alpha install tests >> >> >>> Rob B writes: >>> > >>> > OK ... maybe my terminology was out (a lot). The APECS is in dmesg, >> the >>> > IDE interfaces don't show up at all. >>> >>> Again, it would help, A LOT, to see dmesg, pciconf -lv, and 'show >>> conf' output. (the latter being done from the SRM console). >> >>>>> sho conf >> Digital AlphaPC 64 274MHz >> SRM Console V4.8-1 VMS PALcode V5.56-1, OSF PALcode V1.45-4 >> DECchip (tm) 21064A-2 >> DECchip (tm) 21071-DA Pass 1 >> DECchip (tm) 21071-CA Pass 2 >> >> MEMORY >> 64Meg of system memory >> >> >> PCI Bus >> Bus 00 Slot 05: NCR 53C875 Scsi Controller >> pka0.7.0.5.0 Scsi Bus ID 7 >> dka0.0.0.5.0 COMPAQ >> BD00421936 >> Bus 00 Slot 08: Intel 82378IB PCI to ISA Bridge >> >> ISA >> Slot Device Name Type Enabled >> BaseAddr >> IRQ DMA >> 0 >> 0 MOUSE Embedded Yes 60 >> 12 >> 1 KBD Embedded Yes 60 >> 1 >> 2 COM1 Embedded Yes 3f8 >> 4 >> 3 COM2 Embedded Yes 2f8 >> 3 >> 4 LPT1 Embedded Yes >> 3bc 7 >> 5 FLOPPY Embedded Yes 3f0 >> 6 2 >> >> aylee# dmesg >> Copyright (c) 1992-2002 The FreeBSD Project. >> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 >> The Regents of the University of California. All rights reserved. >> FreeBSD 5.0-DP1 #0: Sun Apr 7 07:34:25 GMT 2002 >> murray@axpbuilder.freebsdmall.com:/usr/src/sys/alpha/compile/GENERIC >> Preloaded elf kernel "/boot/kernel/kernel" at 0xfffffc0000814000. >> EB64+ >> Digital AlphaPC 64 274 MHz, 274MHz >> 8192 byte page size, 1 processor. >> CPU: EV45 (21064A) major=6 minor=2 >> OSF PAL rev: 0x100040002012d >> real memory = 65019904 (63496K bytes) >> avail memory = 55279616 (53984K bytes) >> apecs0: <DECchip 21072 Core Logic chipset> >> pci0: <PCI bus> on pcib0 >> sym0: <875> port 0x10000-0x100ff mem >> 0x8205c000-0x8205cfff,0x8205d000-0x8205d0ff irq 2 at device 5.0 on pci0 >> sym0: Tekram NVRAM, ID 7, Fast-20, SE, parity checking >> sym0: interrupting at APECS irq 2 >> pci0: <display, VGA> at device 7.0 (no driver attached) >> isab0: <PCI-ISA bridge> at device 8.0 on pci0 >> isa0: <ISA bus> on isab0 >> dc0: <Intel 21143 10/100BaseTX> port 0x10100-0x1017f mem >> 0x8205d100-0x8205d17f irq 3 at device 9.0 on pci0 >> dc0: interrupting at APECS irq 3 >> dc0: Ethernet address: 08:00:2b:c3:dd:56 >> miibus0: <MII bus> on dc0 >> dcphy0: <Intel 21143 NWAY media interface> on miibus0 >> dcphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto >> atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0 >> atkbd0: <AT Keyboard> irq 1 on atkbdc0 >> atkbd0: interrupting at ISA irq 1 >> fdc0: <enhanced floppy controller (i82077, NE72065 or clone)> at port >> 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0 >> fdc0: interrupting at ISA irq 6 >> mcclock0: <MC146818A real time clock> at port 0x70-0x71 on isa0 >> ppc0: <Parallel port> at port 0x3bc-0x3c3 irq 7 on isa0 >> ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode >> plip0: cannot reserve interrupt, failed. >> lpt0: <Printer> on ppbus0 >> lpt0: Polled port >> ppi0: <Parallel I/O> on ppbus0 >> ppc0: interrupting at ISA irq 7 >> sc0: <System console> on isa0 >> sc0: VGA <16 virtual consoles, flags=0x200> >> sio0 at port 0x3f8-0x3ff irq 4 on isa0 >> sio0: type 16550A >> sio0: interrupting at ISA irq 4 >> sio1: reserved for low-level i/o >> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on >> isa0 >> Timecounter "i8254" frequency 1193182 Hz >> Timecounter "alpha" frequency 275002485 Hz >> Waiting 15 seconds for SCSI devices to settle >> da0 at sym0 bus 0 target 0 lun 0 >> da0: <COMPAQ BD00421936 3B00> Fixed Direct Access SCSI-2 device >> da0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing >> Enabled >> da0: 4091MB (8380080 512 byte sectors: 255H 63S/T 521C) >> Mounting root from ufs:/dev/da0a >> >> >> aylee# pciconf -lv >> sym0@pci0:5:0: class=0x010000 card=0x00000000 chip=0x000f1000 rev=0x01 >> hdr=0x00 >> vendor = 'Symbios Logic (NCR) (LSI Logic)' >> device = '53C875, 53C876 Ultra-Wide SCSI (53C876 is dual-channel)' >> class = mass storage >> subclass = SCSI >> none0@pci0:7:0: class=0x030000 card=0x00000000 chip=0x0519102b rev=0x01 >> hdr=0x00 >> vendor = 'Matrox Graphics Inc' >> device = 'MGA-2064W Millenium GUI Accelerator' >> class = display >> subclass = VGA >> isab0@pci0:8:0: class=0x000000 card=0x00000000 chip=0x04848086 rev=0x84 >> hdr=0x00 >> vendor = 'Intel Corporation' >> device = '82378ZB/IB,82379AB PCI to ISA Bridge, System I/O' >> class = old >> subclass = non-VGA display device >> dc0@pci0:9:0: class=0x020000 card=0x500b1011 chip=0x00191011 rev=0x30 >> hdr=0x00 >> vendor = 'Digital Equipment Corporation' >> device = 'DC21142/3 PCI/CardBus 10/100 Mbit Ethernet Ctlr' >> class = network >> subclass = ethernet >> >> >>> Also, did this work with previous version of FreeBSD, or is this the >>> first time this machine was installed with FreeBSD? >> >> It's never worked, but I've also not needed it prior to now > > Do you have an ISA ATA controller? If so, try breaking into the > loader (hit a key during the 10 second countdown) and type in the > following: > > set hint.ata.0.at="isa" > set hint.ata.0.port="0x1f0" > set hint.ata.0.irq="14" > set hint.ata.1.at="isa" > set hint.ata.1.port="0x170" > set hint.ata.1.irq="15" > boot > > If it does work, then add the following lines to your /boot/device.hints > file: > > hint.ata.0.at="isa" > hint.ata.0.port="0x1F0" > hint.ata.0.irq="14" > hint.ata.1.at="isa" > hint.ata.1.port="0x170" > hint.ata.1.irq="15" > > Also, if that does work, then we should think about adding those lines > to GENERIC.hints for Alpha. > Thanks John, seems that it works ... now just gotta fix my b0rked fstab. Something went awry in the build - most likely PEBKAC -- Rob To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-alpha" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?oprft47lvyzn6bwz>