Date: Thu, 14 Nov 2002 10:14:49 -0500 (EST) From: John Baldwin <jhb@FreeBSD.org> To: Rob <rbyrnes@ozemail.com.au> Cc: Andrew Gallatin <gallatin@cs.duke.edu>, freebsd-alpha@freebsd.org Subject: Re: 5.0 alpha install tests Message-ID: <XFMail.20021114101449.jhb@FreeBSD.org> In-Reply-To: <oprft47lvyzn6bwz@smtp.ozemail.com.au>
next in thread | previous in thread | raw e-mail | index | archive | help
On 14-Nov-2002 Rob wrote: > On Sat, 09 Nov 2002 09:39:04 -0500 (EST), John Baldwin <jhb@FreeBSD.org> wrote: > >> >> On 09-Nov-2002 Rob B wrote: >>> ----- Original Message ----- >>> From: "Andrew Gallatin" <gallatin@cs.duke.edu> >>> To: "Rob B" <rbyrnes@ozemail.com.au> >>> Cc: <freebsd-alpha@FreeBSD.ORG> >>> Sent: Thursday, November 07, 2002 1:44 PM >>> Subject: Re: 5.0 alpha install tests >>> >>> >>>> Rob B writes: >>>> > >>>> > OK ... maybe my terminology was out (a lot). The APECS is in dmesg, >>> the >>>> > IDE interfaces don't show up at all. >>>> >>>> Again, it would help, A LOT, to see dmesg, pciconf -lv, and 'show >>>> conf' output. (the latter being done from the SRM console). >>> >>>>>> sho conf >>> Digital AlphaPC 64 274MHz >>> SRM Console V4.8-1 VMS PALcode V5.56-1, OSF PALcode V1.45-4 >>> DECchip (tm) 21064A-2 >>> DECchip (tm) 21071-DA Pass 1 >>> DECchip (tm) 21071-CA Pass 2 >>> >>> MEMORY >>> 64Meg of system memory >>> >>> >>> PCI Bus >>> Bus 00 Slot 05: NCR 53C875 Scsi Controller >>> pka0.7.0.5.0 Scsi Bus ID 7 >>> dka0.0.0.5.0 COMPAQ >>> BD00421936 >>> Bus 00 Slot 08: Intel 82378IB PCI to ISA Bridge >>> >>> ISA >>> Slot Device Name Type Enabled >>> BaseAddr >>> IRQ DMA >>> 0 >>> 0 MOUSE Embedded Yes 60 >>> 12 >>> 1 KBD Embedded Yes 60 >>> 1 >>> 2 COM1 Embedded Yes 3f8 >>> 4 >>> 3 COM2 Embedded Yes 2f8 >>> 3 >>> 4 LPT1 Embedded Yes >>> 3bc 7 >>> 5 FLOPPY Embedded Yes 3f0 >>> 6 2 >>> >>> aylee# dmesg >>> Copyright (c) 1992-2002 The FreeBSD Project. >>> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 >>> The Regents of the University of California. All rights reserved. >>> FreeBSD 5.0-DP1 #0: Sun Apr 7 07:34:25 GMT 2002 >>> murray@axpbuilder.freebsdmall.com:/usr/src/sys/alpha/compile/GENERIC >>> Preloaded elf kernel "/boot/kernel/kernel" at 0xfffffc0000814000. >>> EB64+ >>> Digital AlphaPC 64 274 MHz, 274MHz >>> 8192 byte page size, 1 processor. >>> CPU: EV45 (21064A) major=6 minor=2 >>> OSF PAL rev: 0x100040002012d >>> real memory = 65019904 (63496K bytes) >>> avail memory = 55279616 (53984K bytes) >>> apecs0: <DECchip 21072 Core Logic chipset> >>> pci0: <PCI bus> on pcib0 >>> sym0: <875> port 0x10000-0x100ff mem >>> 0x8205c000-0x8205cfff,0x8205d000-0x8205d0ff irq 2 at device 5.0 on pci0 >>> sym0: Tekram NVRAM, ID 7, Fast-20, SE, parity checking >>> sym0: interrupting at APECS irq 2 >>> pci0: <display, VGA> at device 7.0 (no driver attached) >>> isab0: <PCI-ISA bridge> at device 8.0 on pci0 >>> isa0: <ISA bus> on isab0 >>> dc0: <Intel 21143 10/100BaseTX> port 0x10100-0x1017f mem >>> 0x8205d100-0x8205d17f irq 3 at device 9.0 on pci0 >>> dc0: interrupting at APECS irq 3 >>> dc0: Ethernet address: 08:00:2b:c3:dd:56 >>> miibus0: <MII bus> on dc0 >>> dcphy0: <Intel 21143 NWAY media interface> on miibus0 >>> dcphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto >>> atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0 >>> atkbd0: <AT Keyboard> irq 1 on atkbdc0 >>> atkbd0: interrupting at ISA irq 1 >>> fdc0: <enhanced floppy controller (i82077, NE72065 or clone)> at port >>> 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0 >>> fdc0: interrupting at ISA irq 6 >>> mcclock0: <MC146818A real time clock> at port 0x70-0x71 on isa0 >>> ppc0: <Parallel port> at port 0x3bc-0x3c3 irq 7 on isa0 >>> ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode >>> plip0: cannot reserve interrupt, failed. >>> lpt0: <Printer> on ppbus0 >>> lpt0: Polled port >>> ppi0: <Parallel I/O> on ppbus0 >>> ppc0: interrupting at ISA irq 7 >>> sc0: <System console> on isa0 >>> sc0: VGA <16 virtual consoles, flags=0x200> >>> sio0 at port 0x3f8-0x3ff irq 4 on isa0 >>> sio0: type 16550A >>> sio0: interrupting at ISA irq 4 >>> sio1: reserved for low-level i/o >>> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on >>> isa0 >>> Timecounter "i8254" frequency 1193182 Hz >>> Timecounter "alpha" frequency 275002485 Hz >>> Waiting 15 seconds for SCSI devices to settle >>> da0 at sym0 bus 0 target 0 lun 0 >>> da0: <COMPAQ BD00421936 3B00> Fixed Direct Access SCSI-2 device >>> da0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing >>> Enabled >>> da0: 4091MB (8380080 512 byte sectors: 255H 63S/T 521C) >>> Mounting root from ufs:/dev/da0a >>> >>> >>> aylee# pciconf -lv >>> sym0@pci0:5:0: class=0x010000 card=0x00000000 chip=0x000f1000 rev=0x01 >>> hdr=0x00 >>> vendor = 'Symbios Logic (NCR) (LSI Logic)' >>> device = '53C875, 53C876 Ultra-Wide SCSI (53C876 is dual-channel)' >>> class = mass storage >>> subclass = SCSI >>> none0@pci0:7:0: class=0x030000 card=0x00000000 chip=0x0519102b rev=0x01 >>> hdr=0x00 >>> vendor = 'Matrox Graphics Inc' >>> device = 'MGA-2064W Millenium GUI Accelerator' >>> class = display >>> subclass = VGA >>> isab0@pci0:8:0: class=0x000000 card=0x00000000 chip=0x04848086 rev=0x84 >>> hdr=0x00 >>> vendor = 'Intel Corporation' >>> device = '82378ZB/IB,82379AB PCI to ISA Bridge, System I/O' >>> class = old >>> subclass = non-VGA display device >>> dc0@pci0:9:0: class=0x020000 card=0x500b1011 chip=0x00191011 rev=0x30 >>> hdr=0x00 >>> vendor = 'Digital Equipment Corporation' >>> device = 'DC21142/3 PCI/CardBus 10/100 Mbit Ethernet Ctlr' >>> class = network >>> subclass = ethernet >>> >>> >>>> Also, did this work with previous version of FreeBSD, or is this the >>>> first time this machine was installed with FreeBSD? >>> >>> It's never worked, but I've also not needed it prior to now >> >> Do you have an ISA ATA controller? If so, try breaking into the >> loader (hit a key during the 10 second countdown) and type in the >> following: >> >> set hint.ata.0.at="isa" >> set hint.ata.0.port="0x1f0" >> set hint.ata.0.irq="14" >> set hint.ata.1.at="isa" >> set hint.ata.1.port="0x170" >> set hint.ata.1.irq="15" >> boot >> >> If it does work, then add the following lines to your /boot/device.hints >> file: >> >> hint.ata.0.at="isa" >> hint.ata.0.port="0x1F0" >> hint.ata.0.irq="14" >> hint.ata.1.at="isa" >> hint.ata.1.port="0x170" >> hint.ata.1.irq="15" >> >> Also, if that does work, then we should think about adding those lines >> to GENERIC.hints for Alpha. >> > > Thanks John, seems that it works ... now just gotta fix my b0rked fstab. > Something went awry in the build - most likely PEBKAC Ok, great. I'll add those hints to GENERIC.hints then so that this can work out of the box. -- John Baldwin <jhb@FreeBSD.org> <>< http://www.FreeBSD.org/~jhb/ "Power Users Use the Power to Serve!" - http://www.FreeBSD.org/ To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-alpha" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?XFMail.20021114101449.jhb>