Date: Tue, 23 Oct 2012 12:48:43 -0500 From: dweimer <dweimer@dweimer.net> To: <freebsd-questions@freebsd.org> Subject: Re: Bug in LAGG driver at 9.0 =?UTF-8?Q?=3F?= Message-ID: <dab82c647c4b8ee286c40197a6a9caf4@dweimer.net> In-Reply-To: <5086794F.5000209@esiee.fr> References: <5086794F.5000209@esiee.fr>
next in thread | previous in thread | raw e-mail | index | archive | help
On 2012-10-23 06:02, Frank Bonnet wrote: > Hello > > I cannot get the lagg driver to work properly at 9.0 > > the Cisco switch is well configured to support LACP no problem > on that side it supports another Linux server with two aggregated > eth ports that works well. > > here is the config of the FreeBSD 9.0-P3 server > > ifconfig_bce0="up" > ifconfig_bce1="up" > ifconfig_bce2="up" > cloned_interfaces="lagg0" > ifconfig_lagg0="laggproto lacp laggport bce0 laggport bce1 laggport > bce2" > ipv4_addrs_lagg0="147.215.201.21/24" > defaultrouter="147.215.201.1" > > > showing the lagg configuration give the following , only one ethernet > port is active. > > > ifconfig lagg0 > lagg0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 > mtu 1500 > > options=c01bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,VLAN_HWTSO,LINKSTATE> > ether 00:9c:02:9a:97:b0 > inet 147.215.201.21 netmask 0xffffff00 broadcast 147.215.201.255 > nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> > media: Ethernet autoselect > status: active > laggproto lacp > laggport: bce2 flags=0<> > laggport: bce1 flags=0<> > laggport: bce0 flags=1c<ACTIVE,COLLECTING,DISTRIBUTING> > > > > Thanks for any info/idea > > > _______________________________________________ > freebsd-questions@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-questions > To unsubscribe, send any mail to > "freebsd-questions-unsubscribe@freebsd.org" Can you post your Cisco Switch port configuration? I have a two port LAGG using lacp on two separate Dell PowerEdge servers running 9.0-RELEASEp3, below is my config in FreeBSD the only differences I see apart form 2 instead of three ports, is that I named the interface, and used a different syntax to specify the ip addresses, but yours should be correct as well. uname -v FreeBSD 9.0-RELEASE-p3 #0: Tue Jun 26 10:27:21 CDT 2012 ifconfig_bce0="up" ifconfig_bce1="up" cloned_interfaces="lagg6" ifconfig_lagg6_name="DMZ" ifconfig_DMZ="laggproto lacp laggport bce0 laggport bce1" ifconfig_DMZ_alias0="inet 10.50.20.5 netmask 0xffff0000" ifconfig_DMZ_alias1="inet 10.52.20.5 netmask 0xffff0000" defaultrouter="10.50.110.4" DMZ: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=c01bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4,VLAN_HWTSO,LINKSTATE> ether 78:2b:cb:68:9f:1e inet 10.50.20.5 netmask 0xffff0000 broadcast 10.50.255.255 inet 10.52.20.5 netmask 0xffff0000 broadcast 10.52.255.255 nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> media: Ethernet autoselect status: active laggproto lacp laggport: bce1 flags=1c<ACTIVE,COLLECTING,DISTRIBUTING> laggport: bce0 flags=1c<ACTIVE,COLLECTING,DISTRIBUTING> -- Thanks, Dean E. Weimer http://www.dweimer.net/
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?dab82c647c4b8ee286c40197a6a9caf4>