Date: Tue, 05 Mar 2002 12:23:32 -0800 From: "Kevin Oberman" <oberman@es.net> To: sos@freebsd.dk Cc: stable@freebsd.org Subject: Re: Request for testers of new ATA driver patches Message-ID: <20020305202332.D0FF55D06@ptavv.es.net> In-Reply-To: Your message of "Tue, 05 Mar 2002 10:18:35 %2B0100." <200203050918.g259IZB03239@freebsd.dk>
next in thread | previous in thread | raw e-mail | index | archive | help
[-- Attachment #1 --]
> From: Søren Schmidt <sos@freebsd.dk>
> Date: Tue, 5 Mar 2002 10:18:35 +0100 (CET)
>
> Yups a trace from the dump would be very nice if you could get that...
>
> -S=F8ren
>
Soren,
I have now patched a second Dell Optiplex GX150 and it exhibits the
same failure doing an 'fsck -p' or the normal fsck during a full boot.
I have learned a bit more about it.
1. Only occurs when I have add the second drive to the fstab. (The
second drive is all scratch.)
2. The fsck completes on the first two partitions on the master/boot
drive and on the second drive. The third partition on the master drive
times out and the system crashes.
I have transcribed the crash message and will attach it, my dmesg, and
kernel configuration. I hope to get a dump later today or early
tomorrow. I have meetings most of the day tomorrow, s if I don't get
it then, it will be Thursday.
Now, to sound REALLY dumb...I have never have done a crash dump on
FreeBSD and I am not sure of exactly how to do it. I'm guessing it
involves sysctls in loader.conf since the crash happens before the
system gets far enough along for rc.conf to do anything. I'm guessing
kern.dumpdev, kern.coredump, machdep.do_dump, and perhaps
kern.sugid_coredump are the things I need to set, but I'd like to get
them right the first time to minimize the time my system is off-line.
R. Kevin Oberman, Network Engineer
Energy Sciences Network (ESnet)
Ernest O. Lawrence Berkeley National Laboratory (Berkeley Lab)
E-mail: oberman@es.net Phone: +1 510 486-8634
[-- Attachment #2 --]
Mounting root from ufs:/dev/ad0s1a
swapon: adding /dev/ad0s1b as swap device
Automatic boot in progress...
/dev/ad0s1a: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/ad0s1a: clean, 208146 free (386 frags, 25970 blocks, 0.2% fragmentation)
/dev/ad0s1f: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/ad0s1f: clean, 12850939 free (84907 frags, 1595754 blocks, 0.5% fragmentation)
/dev/ad1s1c: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/ad1s1c: clean, 191234589 free (13 frags, 24043022 blocks, 0.0% fragmentation)
ad0: READ command timeout tag=0 serv=0 - resetting
ata0: resetting devices ..
Fatal trap 12: page fault while in kernel mode
fault virtual address = 0x70
fault code = supervisor read, page not present
instruction pointer = 0x8:0xc0161a64
stack pointer = 0x10:0xc02b0758
frame pointer = 0x10:0xc02b077c
code segment = base 0x0, limit 0xfffff, type 0x1b
= DPL 0, pres 1, def32 1, gran 1
procesor eflags = interrupt enabled, resume, IOPL = 0
current process = Idle
interrupt mask = net tty bio cam
trap number = 12
panic:page fault
syncing disks...
done
uptime: 10s
[-- Attachment #3 --]
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.5-STABLE #2: Thu Jan 31 13:43:46 PST 2002
oberman@ptavv.es.net:/usr/obj/usr/src/sys/ESNET
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (996.77-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x68a Stepping = 10
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 267350016 (261084K bytes)
config> en apm
config> q
avail memory = 256659456 (250644K bytes)
Preloaded elf kernel "kernel" at 0xc0372000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc037209c.
Preloaded elf module "agp.ko" at 0xc03720ec.
VESA: v3.0, 32768k memory, flags:0x1, mode table:0xc00c525f (c000525f)
VESA: Matrox Graphics Inc.
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 11 entries at 0xc00fbb40
apm0: <APM BIOS> on motherboard
apm: found APM BIOS v1.2, connected at v1.2
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
agp0: <Intel Generic host to PCI bridge> mem 0xf4000000-0xf7ffffff at device 0.0 on pci0
pcib1: <Intel 82801BA/BAM (ICH2) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <Matrox MGA G400 AGP graphics accelerator> at 0.0 irq 11
pcib2: <Intel 82801BA/BAM (ICH2) Hub to PCI bridge> at device 30.0 on pci0
pci2: <PCI bus> on pcib2
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xec80-0xecff mem 0xfbfffc00-0xfbfffc7f irq 11 at device 12.0 on pci2
xl0: Ethernet address: 00:06:5b:80:b1:fc
miibus0: <MII bus> on xl0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <Intel 82801BA/BAM (ICH2) PCI to LPC bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH2 ATA100 controller> port 0xffa0-0xffaf at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <unknown card> (vendor=0x8086, dev=0x2443) at 31.3 irq 10
pcm0: <Intel 82801BA (ICH2)> port 0xdc40-0xdc7f,0xd800-0xd8ff irq 10 at device 31.5 on pci0
pcm0: measured ac97 link rate at 55937 Hz
orm0: <Option ROMs> at iomem 0xc0000-0xc87ff,0xc8800-0xcbfff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ata1-slave: identify retries exceeded
ad0: 38166MB <IC35L040AVER07-0> [77545/16/63] at ata0-master UDMA100
ad1: 19092MB <IC35L020AVER07-0> [38792/16/63] at ata0-slave UDMA100
acd0: CD-RW <SONY CD-RW CRX160E> at ata1-master using UDMA33
Mounting root from ufs:/dev/ad0s1a
[-- Attachment #4 --]
#
# ESNET -- Standard ESnet kernel configuration file for FreeBSD/i386
# running on Dell PIII systems.
#
# For more information on this file, please read the handbook section on
# Kernel Configuration Files:
#
# http://www.FreeBSD.org/handbook/kernelconfig-config.html
#
# The handbook is also available locally in /usr/share/doc/handbook
# if you've installed the doc distribution, otherwise always see the
# FreeBSD World Wide Web server (http://www.FreeBSD.org/) for the
# latest information.
#
# An exhaustive list of options and more detailed explanations of the
# device lines is also present in the ./LINT configuration file. If you are
# in doubt as to the purpose or necessity of a line, check first in LINT.
#
# $FreeBSD: src/sys/i386/conf/ESNET12/22246.2.34 2001/08/12 15:25:46 rko Exp $
machine i386
#cpu I386_CPU
#cpu I486_CPU
#cpu I586_CPU
cpu I686_CPU
ident ESNET
maxusers 0
#makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols
#options MATH_EMULATE #Support for x87 emulation
options INET #InterNETworking
options INET6 #IPv6 communications protocols
options FFS #Berkeley Fast Filesystem
options FFS_ROOT #FFS usable as root device [keep this!]
options SOFTUPDATES #Enable FFS soft updates support
options UFS_DIRHASH #Improve performance on big directories
options MFS #Memory Filesystem
options MD_ROOT #MD is a potential root device
#options NFS #Network Filesystem
#options NFS_ROOT #NFS usable as root device, NFS required
options MSDOSFS #MSDOS Filesystem
options CD9660 #ISO 9660 Filesystem
options CD9660_ROOT #CD-ROM usable as root, CD9660 required
options PROCFS #Process filesystem
options COMPAT_43 #Compatible with BSD 4.3 [KEEP THIS!]
options SCSI_DELAY=15000 #Delay (in ms) before probing SCSI
options UCONSOLE #Allow users to grab the console
options USERCONFIG #boot -c editor
#options VISUAL_USERCONFIG #visual boot -c editor
options KTRACE #ktrace(1) support
options SYSVSHM #SYSV-style shared memory
options SYSVMSG #SYSV-style message queues
options SYSVSEM #SYSV-style semaphores
options P1003_1B #Posix P1003_1B real-time extensions
options _KPOSIX_PRIORITY_SCHEDULING
options ICMP_BANDLIM #Rate limit bad replies
options KBD_INSTALL_CDEV # install a CDEV entry in /dev
# To make an SMP kernel, the next two are needed
#options SMP # Symmetric MultiProcessor Kernel
#options APIC_IO # Symmetric (APIC) I/O
device isa
#device eisa
device pci
# Floppy drives
device fdc0 at isa? port IO_FD1 irq 6 drq 2
device fd0 at fdc0 drive 0
#device fd1 at fdc0 drive 1
#
# If you have a Toshiba Libretto with its Y-E Data PCMCIA floppy,
# don't use the above line for fdc0 but the following one:
#device fdc0
# ATA and ATAPI devices
device ata0 at isa? port IO_WD1 irq 14
device ata1 at isa? port IO_WD2 irq 15
device ata
device atadisk # ATA disk drives
device atapicd # ATAPI CDROM drives
device atapifd # ATAPI floppy drives
device atapist # ATAPI tape drives
options ATA_STATIC_ID #Static device numbering
# SCSI Controllers
#device ahb # EISA AHA1742 family
#device ahc # AHA2940 and onboard AIC7xxx devices
#device amd # AMD 53C974 (Tekram DC-390(T))
#device isp # Qlogic family
#device ncr # NCR/Symbios Logic
#device sym # NCR/Symbios Logic (newer chipsets)
#options SYM_SETUP_LP_PROBE_MAP=0x40
# Allow ncr to attach legacy NCR devices when
# both sym and ncr are configured
#device adv0 at isa?
#device adw
#device bt0 at isa?
#device aha0 at isa?
#device aic0 at isa?
#device ncv # NCR 53C500
#device nsp # Workbit Ninja SCSI-3
#device stg # TMC 18C30/18C50
# SCSI peripherals
device scbus # SCSI bus (required)
device da # Direct Access (disks)
#device sa # Sequential Access (tape etc)
#device cd # CD
#device pass # Passthrough device (direct SCSI access)
# RAID controllers interfaced to the SCSI subsystem
#device asr # DPT SmartRAID V, VI and Adaptec SCSI RAID
#device dpt # DPT Smartcache - See LINT for options!
#device mly # Mylex AcceleRAID/eXtremeRAID
# RAID controllers
#device aac # Adaptec FSA RAID, Dell PERC2/PERC3
#device ida # Compaq Smart RAID
#device amr # AMI MegaRAID
#device mlx # Mylex DAC960 family
#device twe # 3ware Escalade
# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc0 at isa? port IO_KBD
device atkbd0 at atkbdc? irq 1
device psm0 at atkbdc? irq 12
device vga0 at isa?
options VESA
# splash screen/screen saver
pseudo-device splash
# syscons is the default console driver, resembling an SCO console
device sc0 at isa? flags 0x100
options SC_HISTORY_SIZE=300
# Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver
#device vt0 at isa?
#options XSERVER # support for X server on a vt console
#options FAT_CURSOR # start with block cursor
# If you have a ThinkPAD, uncomment this along with the rest of the PCVT lines
#options PCVT_SCANSET=2 # IBM keyboards are non-std
# Floating point support - do not disable.
device npx0 at nexus? port IO_NPX irq 13
# Power management support (see LINT for more options)
device apm0 at nexus? # Advanced Power Management
# PCCARD (PCMCIA) support
#device card
#device pcic0 at isa? irq 0 port 0x3e0 iomem 0xd0000
#device pcic1 at isa? irq 0 port 0x3e2 iomem 0xd4000 disable
# Serial (COM) ports
device sio0 at isa? port IO_COM1 flags 0x10 irq 4
device sio1 at isa? port IO_COM2 irq 3
#device sio2 at isa? disable port IO_COM3 irq 5
#device sio3 at isa? disable port IO_COM4 irq 9
# Parallel port
device ppc0 at isa? irq 7
device ppbus # Parallel port bus (required)
device lpt # Printer
#device plip # TCP/IP over parallel
device ppi # Parallel port interface device
#device vpo # Requires scbus and da
# PCI Ethernet NICs.
#device de # DEC/Intel DC21x4x (``Tulip'')
#device txp # 3Com 3cR990 (``Typhoon'')
#device vx # 3Com 3c590, 3c595 (``Vortex'')
# PCI Ethernet NICs that use the common MII bus controller code.
# NOTE: Be sure to keep the 'device miibus' line in order to use these NICs!
device miibus # MII bus support
#device dc # DEC/Intel 21143 and various workalikes
#device fxp # Intel EtherExpress PRO/100B (82557, 82558)
#device pcn # AMD Am79C97x PCI 10/100 NICs
#device rl # RealTek 8129/8139
#device sf # Adaptec AIC-6915 (``Starfire'')
#device sis # Silicon Integrated Systems SiS 900/SiS 7016
#device ste # Sundance ST201 (D-Link DFE-550TX)
#device tl # Texas Instruments ThunderLAN
#device tx # SMC EtherPower II (83c170 ``EPIC'')
#device vr # VIA Rhine, Rhine II
#device wb # Winbond W89C840F
#device wx # Intel Gigabit Ethernet Card (``Wiseman'')
device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
# ISA Ethernet NICs.
# 'device ed' requires 'device miibus'
#device ed0 at isa? port 0x280 irq 10 iomem 0xd8000
#device ex
#device ep
#device fe0 at isa? port 0x300
# Xircom Ethernet
#device xe
# PRISM I IEEE 802.11b wireless NIC.
#device awi
# WaveLAN/IEEE 802.11 wireless NICs. Note: the WaveLAN/IEEE really
# exists only as a PCMCIA device, so there is no ISA attachment needed
# and resources will always be dynamically assigned by the pccard code.
#device wi
# Aironet 4500/4800 802.11 wireless NICs. Note: the declaration below will
# work for PCMCIA and PCI cards, as well as ISA cards set to ISA PnP
# mode (the factory default). If you set the switches on your ISA
# card for a manually chosen I/O address and IRQ, you must specify
# those parameters here.
#device an
# The probe order of these is presently determined by i386/isa/isa_compat.c.
#device ie0 at isa? port 0x300 irq 10 iomem 0xd0000
#device le0 at isa? port 0x300 irq 5 iomem 0xd0000
#device lnc0 at isa? port 0x280 irq 10 drq 0
#device cs0 at isa? port 0x300
#device sn0 at isa? port 0x300 irq 10
# Pseudo devices - the number indicates how many units to allocate.
pseudo-device loop # Network loopback
pseudo-device ether # Ethernet support
#pseudo-device sl 1 # Kernel SLIP
#pseudo-device ppp 1 # Kernel PPP
pseudo-device tun # Packet tunnel.
pseudo-device pty # Pseudo-ttys (telnet etc)
pseudo-device md # Memory "disks"
pseudo-device gif # IPv6 and IPv4 tunneling
#pseudo-device faith 1 # IPv6-to-IPv4 relaying (translation)
# The `bpf' pseudo-device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
pseudo-device bpf #Berkeley packet filter
# USB support
device uhci # UHCI PCI->USB interface
device ohci # OHCI PCI->USB interface
device usb # USB Bus (required)
device ugen # Generic
device uhid # "Human Interface Devices"
device ukbd # Keyboard
device ulpt # Printer
device umass # Disks/Mass storage - Requires scbus and da
device ums # Mouse
device uscanner # Scanners
device urio # Diamond Rio MP3 Player
# USB Ethernet, requires mii
device aue # ADMtek USB ethernet
device cue # CATC USB ethernet
device kue # Kawasaki LSI USB ethernet
# Sound card
device pcm
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20020305202332.D0FF55D06>