Date: Mon, 17 Jan 2000 16:03:09 +0100 (CET) From: Trond Endrestol <trond@ramstind.gtf.ol.no> To: FreeBSD questions <freebsd-questions@freebsd.org> Subject: Problems accessing the tapestreamer Message-ID: <Pine.BSF.4.10.10001171550590.639-100000@ramstind.gtf.ol.no>
next in thread | raw e-mail | index | archive | help
Hi,
After cvsup'ped to 3.4-stable, recompiling and reinstalling, I can no
longer access the tapestreamer. I tried booting with the old
3.3-GENERIC kernel and everything works OK with that kernel.
There's no problem with mt or tar, it's kernel related.
Our tapestreamer is identified at reboot as
sa0: <ARCHIVE Python 04106-XXX 7270> Removable Sequential Access SCSI-2 device
sa0: 7.812MB/s transfers (7.812MHz, offset 15)
And it's made by Seagate.
Trying to use mt status with a valid tape inserted results in both
LEDs turned on (both the yellow and the green) and mt hangs. The only
way to kill mt is to hit the eject button on the streamer.
Below is the current dmesg output and the current kernel configuration
file. The kernel configuration file was based on the GENERIC file from
3.3-release and I see no functional difference between the current
kernel configuration file and the current GENERIC file.
Perhaps there's some problem with the sa driver.
Does someone have a clue?
BTW, do I need the pass0 device?
--
Here's the complete dmesg output:
Copyright (c) 1992-1999 FreeBSD Inc.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 3.4-STABLE #0: Wed Jan 12 16:30:34 CET 2000
root@ramstind.gtf.ol.no:/usr/src/sys/compile/RAMSTIND
Timecounter "i8254" frequency 1193182 Hz
Timecounter "TSC" frequency 451025054 Hz
CPU: Pentium III (451.03-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x673 Stepping = 3
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,<b25>>
real memory = 134217728 (131072K bytes)
avail memory = 127696896 (124704K bytes)
Preloaded elf kernel "kernel" at 0xc02bd000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc02bd09c.
Pentium Pro MTRR support enabled
Probing for devices on PCI bus 0:
chip0: <Intel 82443BX host to PCI bridge> rev 0x03 on pci0.0.0
chip1: <Intel 82443BX host to AGP bridge> rev 0x03 on pci0.1.0
chip2: <Intel 82371AB PCI to ISA bridge> rev 0x02 on pci0.7.0
chip3: <Intel 82371AB Power management controller> rev 0x02 on pci0.7.3
xl0: <3Com 3c900B-COMBO Etherlink XL> rev 0x04 int a irq 9 on pci0.11.0
xl0: Ethernet address: 00:50:da:3b:23:2d
xl0: autonegotiation not supported
ahc0: <Adaptec 2940 Ultra2 SCSI adapter> rev 0x00 int a irq 5 on pci0.13.0
ahc0: aic7890/91 Wide Channel A, SCSI Id=7, 16/255 SCBs
Probing for devices on PCI bus 1:
vga0: <ATI model 475a graphics accelerator> rev 0x7a int a irq 11 on pci1.0.0
Probing for devices on the ISA bus:
sc0 on isa
sc0: VGA color <16 virtual consoles, flags=0x0>
atkbdc0 at 0x60-0x6f on motherboard
atkbd0 irq 1 on isa
psm0 irq 12 on isa
psm0: model Generic PS/2 mouse, device ID 0
sio0 at 0x3f8-0x3ff irq 4 flags 0x10 on isa
sio0: type 16550A
sio1 at 0x2f8-0x2ff irq 3 on isa
sio1: type 16550A
fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa
fdc0: FIFO enabled, 8 bytes threshold
fd0: 1.44MB 3.5in
wdc0 not found at 0x1f0
wdc1 at 0x170-0x177 irq 15 on isa
wdc1: unit 0 (atapi): <CREATIVECD4833E/BC102>, removable, intr, dma, iordis
acd0: drive speed 0 - 8250KB/sec, 128KB cache
acd0: supported read types: CD-R, CD-RW, CD-DA, packet track
acd0: Audio: play, 255 volume levels
acd0: Mechanism: ejectable tray
acd0: Medium: no/blank disc inside, unlocked
ppc0 at 0x378 irq 7 flags 0x40 on isa
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
lpt0: <generic printer> on ppbus 0
lpt0: Interrupt-driven port
ppi0: <generic parallel i/o> on ppbus 0
plip0: <PLIP network interface> on ppbus 0
vga0 at 0x3c0-0x3df maddr 0xa0000 msize 131072 on isa
npx0 on motherboard
npx0: INT 16 interface
Waiting 5 seconds for SCSI devices to settle
sa0 at ahc0 bus 0 target 4 lun 0
sa0: <ARCHIVE Python 04106-XXX 7270> Removable Sequential Access SCSI-2 device
sa0: 7.812MB/s transfers (7.812MHz, offset 15)
da0 at ahc0 bus 0 target 1 lun 0
da0: <QUANTUM ATLAS IV 9 WLS 0808> Fixed Direct Access SCSI-3 device
da0: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing Enabled
da0: 8761MB (17942584 512 byte sectors: 255H 63S/T 1116C)
changing root device to da0s1a
--
And here's the current kernel configuration file:
#
# RAMSTIND -- Konfigurasjonsfil for ramstind.gtf.ol.no
# trond, 1999-11-23, basert på
# GENERIC -- Generic machine with WD/AHx/NCR/BTx family disks
#
# For more information on this file, please read the handbook section on
# Kernel Configuration Files:
#
# http://www.freebsd.org/handbook/kernelconfig-config.html
#
# The handbook is also available locally in /usr/share/doc/handbook
# if you've installed the doc distribution, otherwise always see the
# FreeBSD World Wide Web server (http://www.FreeBSD.ORG/) for the
# latest information.
#
# An exhaustive list of options and more detailed explanations of the
# device lines is also present in the ./LINT configuration file. If you are
# in doubt as to the purpose or necessity of a line, check first in LINT.
#
# $FreeBSD: src/sys/i386/conf/GENERIC,v 1.143.2.22 1999/09/14 22:53:30 jkh Exp $
machine "i386"
#cpu "I386_CPU"
#cpu "I486_CPU"
#cpu "I586_CPU"
cpu "I686_CPU"
ident RAMSTIND
maxusers 32
#options MATH_EMULATE #Support for x87 emulation
options INET #InterNETworking
options FFS #Berkeley Fast Filesystem
options FFS_ROOT #FFS usable as root device [keep this!]
options MFS #Memory Filesystem
options MFS_ROOT #MFS usable as root device, "MFS" req'ed
options NFS #Network Filesystem
options NFS_ROOT #NFS usable as root device, "NFS" req'ed
options MSDOSFS #MSDOS Filesystem
options "CD9660" #ISO 9660 Filesystem
options "CD9660_ROOT" #CD-ROM usable as root. "CD9660" req'ed
options PROCFS #Process filesystem
options "COMPAT_43" #Compatible with BSD 4.3 [KEEP THIS!]
options SCSI_DELAY=5000 #Be pessimistic about Joe SCSI device
options UCONSOLE #Allow users to grab the console
options FAILSAFE #Be conservative
options USERCONFIG #boot -c editor
options VISUAL_USERCONFIG #visual boot -c editor
options KTRACE #ktrace(1) syscall trace support
options SYSVSHM #SYSV-style shared memory
options SYSVMSG #SYSV-style message queues
options SYSVSEM #SYSV-style semaphores
config kernel root on da0
# To make an SMP kernel, the next two are needed
#options SMP # Symmetric MultiProcessor Kernel
#options APIC_IO # Symmetric (APIC) I/O
# Optionally these may need tweaked, (defaults shown):
#options NCPU=2 # number of CPUs
#options NBUS=4 # number of busses
#options NAPIC=1 # number of IO APICs
#options NINTR=24 # number of INTs
controller isa0
#controller pnp0 # PnP support for ISA
#controller eisa0
controller pci0
# Floppy drives
controller fdc0 at isa? port "IO_FD1" bio irq 6 drq 2
disk fd0 at fdc0 drive 0
#disk fd1 at fdc0 drive 1
# IDE controller and disks
options "CMD640" # work around CMD640 chip deficiency
controller wdc0 at isa? port "IO_WD1" bio irq 14
#disk wd0 at wdc0 drive 0
#disk wd1 at wdc0 drive 1
controller wdc1 at isa? port "IO_WD2" bio irq 15
#disk wd2 at wdc1 drive 0
#disk wd3 at wdc1 drive 1
# ATAPI devices
options ATAPI #Enable ATAPI support for IDE bus
options ATAPI_STATIC #Don't do it as an LKM
device acd0 #IDE CD-ROM
#device wfd0 #IDE Floppy (e.g. LS-120)
# SCSI Controllers
# A single entry for any of these controllers (ncr, ahb, ahc) is
# sufficient for any number of installed devices.
#controller ncr0 # NCR/Symbios Logic
#controller ahb0 # EISA AHA1742 family
controller ahc0 # AHA2940 and onboard AIC7xxx devices
#controller amd0 # AMD 53C974 (Teckram DC-390(T))
#controller isp0 # Qlogic family
#controller dpt0 # DPT Smartcache - See LINT for options!
#controller adv0 at isa? port ? cam irq ?
#controller adw0
#controller bt0 at isa? port ? cam irq ?
#controller aha0 at isa? port ? cam irq ?
# SCSI peripherals
# Only one of each of these is needed, they are dynamically allocated.
controller scbus0 # SCSI bus (required)
device da0 # Direct Access (disks)
device sa0 # Sequential Access (tape etc)
#device cd0 # CD
device pass0 # Passthrough device (direct SCSI)
# Proprietary or custom CD-ROM Interfaces
#device wt0 at isa? port 0x300 bio irq 5 drq 1
#device mcd0 at isa? port 0x300 bio irq 10
#device matcd0 at isa? port 0x230 bio
#device scd0 at isa? port 0x230 bio
# atkbdc0 controls both the keyboard and the PS/2 mouse
controller atkbdc0 at isa? port IO_KBD tty
device atkbd0 at isa? tty irq 1
device psm0 at isa? tty irq 12
device vga0 at isa? port ? conflicts
# splash screen/screen saver
pseudo-device splash
# syscons is the default console driver, resembling an SCO console
device sc0 at isa? tty
# Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver
#device vt0 at isa? tty
#options XSERVER # support for X server
#options FAT_CURSOR # start with block cursor
# If you have a ThinkPAD, uncomment this along with the rest of the PCVT lines
#options PCVT_SCANSET=2 # IBM keyboards are non-std
# Floating point support - do not disable.
device npx0 at isa? port IO_NPX irq 13
# Power management support (see LINT for more options)
#device apm0 at isa? disable flags 0x31 # Advanced Power Management
# PCCARD (PCMCIA) support
#controller card0
#device pcic0 at card?
#device pcic1 at card?
# Serial (COM) ports
device sio0 at isa? port "IO_COM1" flags 0x10 tty irq 4
device sio1 at isa? port "IO_COM2" tty irq 3
device sio2 at isa? disable port "IO_COM3" tty irq 5
device sio3 at isa? disable port "IO_COM4" tty irq 9
# Parallel port
device ppc0 at isa? port? flags 0x40 net irq 7
controller ppbus0 # Parallel port bus (required)
device lpt0 at ppbus? # Printer
device plip0 at ppbus? # TCP/IP over parallel
device ppi0 at ppbus? # Parallel port interface device
#controller vpo0 at ppbus? # Requires scbus and da0
# PCI Ethernet NICs.
#device al0 # ADMtek AL981 (``Comet'')
#device ax0 # ASIX AX88140A
#device de0 # DEC/Intel DC21x4x (``Tulip'')
#device fxp0 # Intel EtherExpress PRO/100B (82557, 82558)
#device mx0 # Macronix 98713/98715/98725 (``PMAC'')
#device pn0 # Lite-On 82c168/82c169 (``PNIC'')
#device rl0 # RealTek 8129/8139
#device sf0 # Adaptec AIC-6915 DuraLAN (``Starfire'')
#device tl0 # Texas Instruments ThunderLAN
#device tx0 # SMC 9432TX (83c170 ``EPIC'')
#device vr0 # VIA Rhine, Rhine II
#device vx0 # 3Com 3c590, 3c595 (``Vortex'')
#device wb0 # Winbond W89C840F
device xl0 # 3Com 3c90x (``Boomerang'', ``Cyclone'')
# ISA Ethernet NICs.
# Order is important here due to intrusive probes, do *not* alphabetize
# this list of network interfaces until the probes have been fixed.
# Right now it appears that the ie0 must be probed before ep0. See
# revision 1.20 of this file.
#device ed0 at isa? port 0x280 net irq 10 iomem 0xd8000
#device ie0 at isa? port 0x300 net irq 10 iomem 0xd0000
#device ep0 at isa? port 0x300 net irq 10
#device ex0 at isa? port? net irq?
#device fe0 at isa? port 0x300 net irq ?
#device le0 at isa? port 0x300 net irq 5 iomem 0xd0000
#device lnc0 at isa? port 0x280 net irq 10 drq 0
#device cs0 at isa? port 0x300 net irq ?
# requires PCCARD (PCMCIA) support to be activated
#device xe0 at isa? port? net irq ?
# PCCARD NIC drivers.
# ze and zp take over the pcic and cannot coexist with generic pccard
# support, nor the ed and ep drivers they replace.
#device ze0 at isa? port 0x300 net irq 10 iomem 0xd8000
#device zp0 at isa? port 0x300 net irq 10 iomem 0xd8000
# Pseudo devices - the number indicates how many units to allocated.
pseudo-device loop # Network loopback
pseudo-device ether # Ethernet support
#pseudo-device sl 1 # Kernel SLIP
#pseudo-device ppp 1 # Kernel PPP
#pseudo-device tun 1 # Packet tunnel
pseudo-device pty 16 # Pseudo-ttys (telnet etc)
pseudo-device gzip # Exec gzipped a.out's
# The `bpfilter' pseudo-device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
# The number of devices determines the maximum number of
# simultaneous BPF clients programs runnable.
pseudo-device bpfilter 4 #Berkeley packet filter
#####################################################################
# Spesialvalg for RAMSTIND #
#####################################################################
options "NO_F00F_HACK"
options DDB
options DDB_UNATTENDED
options PERFMON
options KERNFS
options QUOTA
#pseudo-device speaker
pseudo-device snp 4
#options CLK_USE_TSC_CALIBRATION
#controller usb0
#controller uhci0
#controller ohci0
#device ugen0
#device uhid0
#device ukbd0
#device ulpt0
#device ums0
#####################################################################
# Slutt på spesialvalgene for RAMSTIND #
#####################################################################
# Slutt på konfigurasjonsfilen RAMSTIND
----------------------------------------------------------------------
Trond Endrestøl | trond@gtf.ol.no
Merkantilvegen 59HB7, | trond@ramstind.gtf.ol.no
N-2815 GJØVIK, NORWAY |+47 61139424 || +47 63874242
Patron of The Art of Computer Programming| FreeBSD 3.4 & Pine 4.10
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.4.10.10001171550590.639-100000>