Date: Mon, 17 Mar 2003 17:03:13 -0700 (MST) From: "Lucas Reddinger" <lucas@wlwhosting.com> To: <mdodd@FreeBSD.ORG> Cc: <current@freebsd.org> Subject: Re: Hang on Boot (still) Message-ID: <1060.216.187.134.163.1047945793.squirrel@mail.wlwhosting.com> In-Reply-To: <20030317060229.M8716@sasami.jurai.net> References: <1058.216.187.134.163.1047877501.squirrel@mail.wlwhosting.com> <20030317060229.M8716@sasami.jurai.net>
next in thread | previous in thread | raw e-mail | index | archive | help
>:D
I booted the two floppies again. I tried what you said. hw.eisa_slots="0".
It got farther this time. I got a full dmesg. However, it was followed by
this:
Fatal trap 12: page fault while in kernel mode
fault virtual address = 0x7
fault code = supervisor read, page not present
instructor pointer = 0x8:0xc01f0cc9
stack pointer = 0x10:0xcf2a3788
frame pointer = 0x10:0xcf2a3794
code segment = base 0x0, limit 0xfffff, type 0x1b
= DPL 0, pres 1, def32 1, gran 1
processor eflags = interrupt enabled, resume, IOPL=0
current process = 1 (sysinstall)
trap number = 12
panic: page fault
Doing a hw.eisa_slots="1" resulted in the same problem. So I decided to
try a 5.0-RELEASE CD. I tried hw.eisa_slots="0", which resulted in the
same crappy error I always got with 5.0-R. Then I remembered that ACPI
wasn't disabled in 5.0-R by default. so I used the hint and disabled it. I
got a lot farther, but it eventually hung with a message like "cbb0: Card
not supported", then it would reboot itself after a few seconds. So I
decided to try a few other hints. It ended up that this combination of
variables on my 5.0-RELEASE would get me booted and into sysinstall:
hw.eisa_slots="0"
hint.acpi.0.disabled=1
hint.pcic.0.disabled=1
So, disabling pcic0 did the trick. Then, I decided to go back to my
snapshot and try this. However, I got the same page fault as described
above. So what happened between 5.0-R and -C? I'll get my 5.0-R installed,
and then I'll try to make world.
Lucas Reddinger
> On Sun, 16 Mar 2003, Lucas Reddinger wrote:
>> The one alternative would be to compile a stripped kernel on another
>> machine, and install off of it. I did this, but I do not have enough
>> knowledge of the 5.x kernel/modules to be able to do this myself. If
>> someone could give me some help with this instead, it would be greatly
>> appriciated.
>
> Try setting this from the loader
>
> hw.eisa_slots="0"
>
> (or 1).
>
> --
> | Matthew N. Dodd | '78 Datsun 280Z | '75 Volvo 164E | FreeBSD/NetBSD
> | | winter@jurai.net | 2 x '84 Volvo 245DL |
> ix86,sparc,pmax | | http://www.jurai.net/~winter | For Great Justice!
> | ISO8802.5 4ever |
--
Lucas Reddinger
Customer Service
Winged Leopard Web Designs
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-current" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?1060.216.187.134.163.1047945793.squirrel>