Date: Mon, 24 Nov 2014 19:09:59 +0300 From: "Alexey V. Panfilov" <lehis2000@mail.ru> To: freebsd-net@freebsd.org Subject: Re: IPMI stops respond if boot in single user mode Message-ID: <54735857.2010209@mail.ru> In-Reply-To: <546F1A96.1060309@mail.ru> References: <546F1A96.1060309@mail.ru>
next in thread | previous in thread | raw e-mail | index | archive | help
21.11.2014 13:57, Alexey V. Panfilov wrote: > Hi, > > My IBM System x3250 M5 has IPMI. It shares onboard NIC Broadcom BCM5719. > I'm setup it and IPMI works perfectly. > But when server boots in single user mode IPMI's IP becomes unreachable. > It occures when bge0 init. > > Any hints? > > Thanks. > > > Details are: > > FreeBSD 10.1-STABLE (r274690) amd64 > > /boot/loader.conf > hw.bge.allow_asf=1 > > > bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. > 0x5719001> mem > 0x82a50000-0x82a5ffff,0x82a40000-0x82a4ffff,0x82a30000-0x82a3ffff irq 16 > at device 0.0 on pci6 > bge0: APE FW version: NCSI v1.2.33.0 > bge0: CHIP ID 0x05719001; ASIC REV 0x5719; CHIP REV 0x57190; PCI-E > miibus0: <MII bus> on bge0 > brgphy0: <BCM5719C 1000BASE-T media interface> PHY 1 on miibus0 > brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, > 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow > bge0: Using defaults for TSO: 65518/35/2048 > bge0: Ethernet address: 6c:ae:8b:5b:74:98 > > > bge0@pci0:6:0:0: class=0x020000 card=0x04911014 chip=0x165714e4 > rev=0x01 hdr=0x00 > vendor = 'Broadcom Corporation' > device = 'NetXtreme BCM5719 Gigabit Ethernet PCIe' > class = network > subclass = ethernet > bar [10] = type Prefetchable Memory, range 64, base 0x82a50000, > size 65536, enabled > bar [18] = type Prefetchable Memory, range 64, base 0x82a40000, > size 65536, enabled > bar [20] = type Prefetchable Memory, range 64, base 0x82a30000, > size 65536, enabled > cap 01[48] = powerspec 3 supports D0 D3 current D0 > cap 03[50] = VPD > cap 05[58] = MSI supports 8 messages, 64 bit enabled with 1 message > cap 11[a0] = MSI-X supports 17 messages > Table in map 0x20[0x0], PBA in map 0x20[0x1000] > cap 10[ac] = PCI-Express 2 endpoint max data 128(256) FLR link x2(x4) > speed 5.0(5.0) ASPM disabled(L0s/L1) > ecap 0001[100] = AER 1 0 fatal 0 non-fatal 1 corrected > ecap 0003[13c] = Serial 1 00006cae8b5b7498 > ecap 0004[150] = Power Budgeting 1 > ecap 0002[160] = VC 1 max VC0 > > When it boots in single-user mode and manually run: #ifconfig bge0 up then ipmi become accessable. How it can be fixed automatically after system is boot in single-user mode? -- With best regards, Alexey V. Panfilov phone: (495)678-8007 ext 6000 mail: lehis@starnet.ru -- Best regards, Alexey V. Panfilov
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?54735857.2010209>