Date: Fri, 3 Dec 2004 17:37:26 -0500 (EST) From: Matt Juszczak <matt@atopia.net> To: Wilko Bulte <wb@freebie.xs4all.nl> Cc: freebsd-alpha@freebsd.org Subject: Re: FreeBSD Boot on a Alpha 433 Message-ID: <20041203173545.U94026@neptune.atopia.net> In-Reply-To: <20041202223208.GC30464@freebie.xs4all.nl> References: <56213.134.210.7.179.1101315838.squirrel@134.210.7.179> <54705.134.210.7.179.1102024664.squirrel@134.210.7.179> <20041202223208.GC30464@freebie.xs4all.nl>
next in thread | previous in thread | raw e-mail | index | archive | help
Here ya go...
>>>boot dka0
(boot dka0.0.0.4.0 -flags A)
block 0 of dka0.0.0.4.0 is a valid boot block
reading 410 blocks from dka0.0.0.4.0
bootstrap code read in
base = 1d8000, image_start = 0, image_bytes = 33400
initializing HWRPB at 2000
initializing page table at 1ca000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
Console: SRM firmware console
VMS PAL rev: 0x1000000010114
OSF PAL rev: 0x1000000020116
Switch to OSF PAL code succeeded.
FreeBSD/alpha SRM CD9660 boot, Revision 1.2
(root@ds10.wbnet, Fri Nov 5 04:07:45 UTC 2004)
Memory: 262144 k
Loading /boot/defaults/loader.conf
/boot/kernel/kernel data=0x5c4ce0+0x3d990 syms=[0x8+0x64ab8+0x8+0x53436]
|
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...
Entering /boot/kernel/kernel at 0xfffffc0000344c30...
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.3-RELEASE #0: Fri Nov 5 11:30:09 UTC 2004
root@ds10.wbnet:/usr/obj/usr/src/sys/GENERIC
Digital Personal Workstation (Miata)
Digital Personal WorkStation 433au, 432MHz
8192 byte page size, 1 processor.
CPU: EV56 (21164A) major=7 minor=0 extensions=0x1<BWX>
OSF PAL rev: 0x1000000020116
real memory = 266493952 (254 MB)
avail memory = 247070720 (235 MB)
cia0: <2117x Core Logic chipset>
cia0: Pyxis, pass 1
cia0: extended capabilities: 1<BWEN>
cia0: WARNING: Pyxis pass 1 DMA bug; no bets...
pcib0: <2117x PCI host bus adapter> on cia0
pci0: <PCI bus> on pcib0
dc0: <Intel 21143 10/100BaseTX> port 0x9000-0x907f mem
0x80148000-0x8014807f irq 0 at device 3.0 on pci0
miibus0: <MII bus> on dc0
nsphy0: <DP83840 10/100 media interface> on miibus0
nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
dc0: Ethernet address: 00:00:f8:75:e8:fd
dc0: if_start running deferred for Giant
dc0: interrupting at CIA irq 0
dc0: [GIANT-LOCKED]
atapci0: <CMD 646 WDMA2 controller> port
0x9080-0x908f,0x376,0x170-0x177,0x3f6,0 x1f0-0x1f7 irq 1 at device 4.0 on
pci0
atapci0: interrupting at CIA irq 1
ata0: channel #0 on atapci0
ata0: interrupting at ISA irq 14
ata1: channel #1 on atapci0
ata1: interrupting at ISA irq 15
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
pci0: <display, VGA> at device 11.0 (no driver attached)
pcib1: <PCI-PCI bridge> at device 20.0 on pci0
pci1: <PCI bus> on pcib1
isp0: <Qlogic ISP 1020/1040 PCI SCSI Adapter> port 0x8000-0x80ff mem
0x80010000- 0x80010fff irq 16 at device 9.0 on pci1
isp0: interrupting at CIA irq 16
isp0: [GIANT-LOCKED]
halted CPU 0
halt code = 5
HALT instruction executed
PC = 1f00
>>>show conf
Firmware
SRM Console: V7.2-1 Mar 6 2000 14:47:02
ARC Console: 5.70
PALcode: OpenVMS PALcode V1.20-16, Tru64 UNIX PALcode V1.22-18
SROM Version: v5.90
Processor
DECchip (tm) 21164A-1 Pass 433 MHz 96 KBytes SCache
2 MB BCache
PYXIS ASIC Pass 257
MEMORY
Memory Size = 256Mb
Bank Size/Sets Base Addr
------ ---------- ---------
0 128Mb 00000000
1 128Mb 08000000
BCache Size = 2Mb
Tested Memory = 256Mbytes
PCI Bus
Bus 00 Slot 03: Digital Semiconductor 21143 Network Controller
ewa0.0.0.3.0 00-00-F8-75-E8-FD
Bus 00 Slot 04: PCI IDE
pqb0.0.1.4.0 PCI EIDE
dka0.0.0.4.0 TOSHIBA CD-ROM
XM-61
Bus 00 Slot 07: Intel SIO 82378
Bus 00 Slot 11: Digital TGA2 Graphics Controller
Bus 00 Slot 20: DECchip 21152 PCI to PCI Bridge
Bus 01 Slot 09: ISP1040 Scsi Controller
pkc0.7.0.1009.0 SCSI Bus ID 7
dkc200.2.0.1009.0 RZ1CC-BA
dkc300.3.0.1009.0 QUANTUM
ATLAS10K2-TY
ISA
Slot Device Name Type Enabled BaseAddr IRQ
DMA
0
0 MOUSE Embedded Yes 60 12
1 KBD Embedded Yes 60 1
2 COM1 Embedded Yes 3f8 4
3 COM2 Embedded Yes 2f8 3
4 LPT1 Embedded Yes 3bc 7
5 FLOPPY Embedded Yes 3f0 6 2
6 EIDE Embedded Yes 1f0 14
3f6 15
170
376
7 ES1888 Embedded Yes 220 5 1
5
>>>show dev
dka0.0.0.4.0 DKA0 TOSHIBA CD-ROM XM-6102B 1106
dkc200.2.0.1009.0 DKC200 RZ1CC-BA 883F
dkc300.3.0.1009.0 DKC300 QUANTUM ATLAS10K2-TY092L DA40
dva0.0.0.0.1 DVA0
ewa0.0.0.3.0 EWA0 00-00-F8-75-E8-FD
pkc0.7.0.1009.0 PKC0 SCSI Bus ID 7 5.57
pqa0.0.0.4.0 PQA0 PCI EIDE
pqb0.0.1.4.0 PQB0 PCI EIDE
>>>
On Thu, 2 Dec 2004, Wilko Bulte wrote:
> On Thu, Dec 02, 2004 at 04:57:44PM -0500, Matt Juszczak wrote..
>> It is 5.3-RELEASE
>> show DEV and show CONF output a lot of information. I'm able to do:
>>
>> show DEV > out
>> show CONF >> out
>> cat out | more
>>
>> and see the out file, but no idea how to get it to you.... (not that familiar with srm).
>
> Oh.. that is in fact not too difficult: use a serial console. Your machine
> will happily talk 9600N81 on its serial port from that point on.
>
> You can also do a >>> SET CONSOLE SERIAL from the VGA console, and after
> an INIT your console will show up
>
> Once you have the serial port connected to (say) another FreeBSD box
> you can use something like tip to connect to the Alpha. I assume
> you know how to capture things with 'script' or something like that.
>
> That output is of course quite easily email-able
>
>> Exact message is haltcode=5, CPU0 halted. Do you want the 4 character hex # too?
>>
>> -Matt
>>
>>> On Wed, Nov 24, 2004 at 12:03:58PM -0500, Matt Juszczak wrote..
>>>
>>>> Hello,
>>>>
>>>>
>>>> I have a personal workstation (433) Digital Alpha and when I do "boot
>>>> dka0" the kernel loads off the CD (I'm trying to install BSD). It even
>>>> gets passed hard drive detection but just dies with a haltcode. Any
>>>> ideas?
>>>
>>> Some details would come in handy:
>>> - what revision FreeBSD did you try?
>>> - SHOW DEV from the >>> console prompt.
>>> - SHOW CONF from the >>> console prompt.
>>> - what is the exact haltcode etc message do you get?
>
> --
> Wilko Bulte wilko@FreeBSD.org
>
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20041203173545.U94026>