Date: Thu, 27 Jan 2005 09:52:28 +0000 From: Jason Thomson <jason.thomson@mintel.com> To: Vinod Kashyap <vkashyap@amcc.com> Cc: freebsd-stable@freebsd.org Subject: Re: 3ware 9500S problem in newly updated 4.x box. Message-ID: <41F8B9DC.1080608@mintel.com> In-Reply-To: <IAXU4302.7LS@hadar.amcc.com> References: <IAXU4302.7LS@hadar.amcc.com>
next in thread | previous in thread | raw e-mail | index | archive | help
That worked. Thank you. Vinod Kashyap wrote: > See if this fixes your problem. > > Index: twa_cam.c > =================================================================== > RCS file: /home/ncvs/src/sys/dev/twa/twa_cam.c,v > retrieving revision 1.1.2.4 > diff -u -r1.1.2.4 twa_cam.c > --- twa_cam.c 7 Jan 2005 01:00:45 -0000 1.1.2.4 > +++ twa_cam.c 26 Jan 2005 18:53:54 -0000 > @@ -424,9 +424,9 @@ > twa_dbg_dprint(3, sc, "XPT_PATH_INQ request"); > > path_inq->version_num = 1; > - path_inq->hba_inquiry = PI_WIDE_16; > + path_inq->hba_inquiry = 0; > path_inq->target_sprt = 0; > - path_inq->hba_misc |= PIM_NOBUSRESET; > + path_inq->hba_misc = 0; > path_inq->hba_eng_cnt = 0; > path_inq->max_target = TWA_MAX_UNITS; > path_inq->max_lun = 0; > > > >>-----Original Message----- >>From: owner-freebsd-stable@freebsd.org >>[mailto:owner-freebsd-stable@freebsd.org]On Behalf Of Jason Thomson >>Sent: Wednesday, January 26, 2005 7:52 AM >>To: freebsd-stable@freebsd.org >>Cc: Vinod Kashyap >>Subject: 3ware 9500S problem in newly updated 4.x box. >> >> >>Recently CVSupped and rebuilt a releng4 box. >> >>This box has a 9500S in RAID10 configuration. >> >>On reboot, it failed to find da0, so it couldn't mount root. >> >>If you wait a few seconds, and then type to specify the root >>filesystem >>again, then the da0 device is found (the message is printed as you >>type), and on hitting return, the machine continues booting. >> >>(See dmesg below). >> >> >>The twa driver and firmware are up to date. >> >>This is a DELL 1600SC SMP. HyperThreading is enabled (but it's not a >>big deal to us one way or the other, so if it's a good idea >>to turn it >>off, we could). >> >>If you don't type on the keyboard, then the message doesn't >>appear. I >>haven't tried this without SMP. It's a production box I just >>upgraded, >>and can only mess around with it early in the morning. >> >>Before today, it was running FreeBSD 4-STABLE from September 24th. >> >>Has anyone else seen this? Does anyone have any ideas? Is there >>anything I can try to debug this? >> >> >> >> >> >> >> >>Copyright (c) 1992-2005 The FreeBSD Project. >>Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, >>1993, 1994 >> The Regents of the University of California. All >>rights reserved. >>FreeBSD 4.11-STABLE #3: Wed Jan 26 14:03:18 GMT 2005 >> jason@baldrick.mintel.co.uk:/usr/obj/usr/src/sys/BALDRICK >>Timecounter "i8254" frequency 1193182 Hz >>CPU: Intel(R) Xeon(TM) CPU 2.80GHz (2790.72-MHz 686-class CPU) >> Origin = "GenuineIntel" Id = 0xf29 Stepping = 9 >> >>Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SE > > P,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> > >> Hyperthreading: 2 logical CPUs >>real memory = 3757965312 (3669888K bytes) >>avail memory = 3659362304 (3573596K bytes) >>Changing APIC ID for IO APIC #0 from 0 to 8 on chip >>Changing APIC ID for IO APIC #1 from 0 to 9 on chip >>Changing APIC ID for IO APIC #2 from 0 to 10 on chip >>Programming 16 pins in IOAPIC #0 >>IOAPIC #0 intpin 2 -> irq 0 >>Programming 16 pins in IOAPIC #1 >>Programming 16 pins in IOAPIC #2 >>FreeBSD/SMP: Multiprocessor motherboard: 4 CPUs >> cpu0 (BSP): apic id: 0, version: 0x00050014, at 0xfee00000 >> cpu1 (AP): apic id: 1, version: 0x00050014, at 0xfee00000 >> cpu2 (AP): apic id: 6, version: 0x00050014, at 0xfee00000 >> cpu3 (AP): apic id: 7, version: 0x00050014, at 0xfee00000 >> io0 (APIC): apic id: 8, version: 0x000f0011, at 0xfec00000 >> io1 (APIC): apic id: 9, version: 0x000f0011, at 0xfec01000 >> io2 (APIC): apic id: 10, version: 0x000f0011, at 0xfec02000 >>pnpbios: Bad PnP BIOS data checksum >>Preloaded elf kernel "kernel" at 0xa03f0000. >>Warning: Pentium 4 CPU: PSE disabled >>Pentium Pro MTRR support enabled >>md0: Malloc disk >>Using $PIR table, 9 entries at 0xa00fc200 >>npx0: <math processor> on motherboard >>npx0: INT 16 interface >>pcib0: <ServerWorks host to PCI bridge(unknown chipset)> on >>motherboard >>IOAPIC #1 intpin 0 -> irq 2 >>IOAPIC #1 intpin 9 -> irq 3 >>pci0: <PCI bus> on pcib0 >>em0: <Intel(R) PRO/1000 Network Connection, Version - 1.7.35> port >>0xecc0-0xecff mem 0xfe100000-0xfe11ffff irq 2 at device 2.0 on pci0 >>em0: Speed:N/A Duplex:N/A >>sis0: <NatSemi DP83815 10/100BaseTX> port 0xe800-0xe8ff mem >>0xfe122000-0xfe122fff irq 3 at device 4.0 on pci0 >>sis0: Ethernet address: 00:02:e3:02:6e:10 >>miibus0: <MII bus> on sis0 >>ukphy0: <Generic IEEE 802.3u media interface> on miibus0 >>ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto >>pci0: <ATI Mach64-GR graphics accelerator> at 14.0 >>atapci0: <ServerWorks CSB5 ATA100 controller> port >>0x8b0-0x8bf,0x374-0x377,0x170-0x177,0x3f4-0x3f7,0x1f0-0x1f7 at device >>15.1 on pci0 >>ata0: at 0x1f0 irq 14 on atapci0 >>ata1: at 0x170 irq 15 on atapci0 >>pci0: <OHCI USB controller> at 15.2 irq 5 >>isab0: <PCI to ISA bridge (vendor=1166 device=0225)> at >>device 15.3 on pci0 >>isa0: <ISA bus> on isab0 >>pcib1: <ServerWorks host to PCI bridge(unknown chipset)> on >>motherboard >>IOAPIC #1 intpin 4 -> irq 10 >>pci1: <PCI bus> on pcib1 >>3ware device driver for 9000 series storage controllers, version: >>2.40.02.011 >>twa0: <3ware 9000 series Storage Controller> port 0xdc00-0xdcff mem >>0xfc000000-0xfc7fffff,0xfcf00000-0xfcf000ff irq 10 at device >>6.0 on pci1 >>twa0: 4 ports, Firmware FE9X 2.04.00.005, BIOS BE9X 2.03.01.047 >>pcib2: <Host to PCI bridge> on motherboard >>pci2: <PCI bus> on pcib2 >>pcib3: <ServerWorks host to PCI bridge(unknown chipset)> on >>motherboard >>pci3: <PCI bus> on pcib3 >>pcib4: <ServerWorks host to PCI bridge(unknown chipset)> on >>motherboard >>pci4: <PCI bus> on pcib4 >>orm0: <Option ROMs> at iomem >>0xc0000-0xc7fff,0xc8000-0xc97ff,0xe3000-0xea7ff,0xec000-0xefff >>f on isa0 >>pmtimer0 on isa0 >>fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 >>drq 2 on isa0 >>fdc0: FIFO enabled, 8 bytes threshold >>fd0: <1440-KB 3.5" drive> on fdc0 drive 0 >>atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 >>atkbd0: <AT Keyboard> irq 1 on atkbdc0 >>kbd0 at atkbd0 >>vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem >>0xa0000-0xbffff on isa0 >>sc0: <System console> at flags 0x100 on isa0 >>sc0: VGA <16 virtual consoles, flags=0x300> >>sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 >>sio0: type 16550A >>sio1: configured irq 3 not in bitmap of probed irqs 0 >>ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 >>ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode >>ppc0: FIFO with 16/16/8 bytes threshold >>lpt0: <Printer> on ppbus0 >>lpt0: Interrupt-driven port >>APIC_IO: Testing 8254 interrupt delivery >>APIC_IO: Broken MP table detected: 8254 is not connected to IOAPIC #0 >>intpin 2 >>APIC_IO: routing 8254 via 8259 and IOAPIC #0 intpin 0 >>IP packet filtering initialized, divert enabled, rule-based forwarding >>enabled, default to deny, logging limited to 1000 >>packets/entry by default >>IPsec: Initialized Security Association Processing. >>SMP: AP CPU #2 Launched! >>SMP: AP CPU #1 Launched! >>SMP: AP CPU #3 Launched! >>acd0: CDROM <SAMSUNG CD-ROM SC-148A> at ata1-master PIO4 >>Mounting root from ufs:/dev/da0s1a >>no such device 'da' >>setrootbyname failed >>ffs_mountroot: can't find rootvp >>Root mount failed: 6 >> >>Manual root filesystem specification: >> <fstype>:<device> Mount <device> using filesystem <fstype> >> eg. ufs:/dev/da0s1a >> ? List valid disk boot devices >> <empty line> Abort manual input >> >>mountroot> ufs\^[[}\^[[}:/dev/da0s1a >>Mounting root from ufs\^[[}\^[[}:/dev/da0s1a >>ffs_mountroot: can't find rootvp >>Root mount failed: 6 >> >>Manual root filesystem specification: >> <fstype>:<device> Mount <device> using filesystem <fstype> >> eg. ufs:/dev/da0s1a >> ? List valid disk boot devices >> <empty line> Abort manual input >> >>mountroot> da0 at twa0 bus 0 target 0 lun 0 >>da0: <3ware Logical Disk 00 1.00> Fixed Direct Access SCSI-0 device >>da0: 100.000MB/s transfers >>da0: 381448MB (781205504 512 byte sectors: 255H 63S/T 48627C) >>ufs:/dev/da0s1a >>Mounting root from ufs:/dev/da0s1a >>ohci0: <OHCI (generic) USB controller> mem 0xfe120000-0xfe120fff irq 5 >>at device 15.2 on pci0 >>usb0: OHCI version 1.0, legacy support >>usb0: SMM does not respond, resetting >>usb0: <OHCI (generic) USB controller> on ohci0 >>usb0: USB revision 1.0 >>uhub0: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 >>uhub0: 2 ports with 2 removable, self powered >>em0: Link is up 100 Mbps Full Duplex >> >> >> >>_______________________________________________ >>freebsd-stable@freebsd.org mailing list >>http://lists.freebsd.org/mailman/listinfo/freebsd-stable >>To unsubscribe, send any mail to >>"freebsd-stable-unsubscribe@freebsd.org" >> > > > > _______________________________________________ > freebsd-stable@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-stable > To unsubscribe, send any mail to "freebsd-stable-unsubscribe@freebsd.org" > > >
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?41F8B9DC.1080608>