Date: Tue, 21 Mar 2000 08:14:28 +0300 (MSK) From: "Ilmar S. Habibulin" <ilmar@ints.ru> To: freebsd-current@freebsd.org Subject: -current sudden panics :( Message-ID: <Pine.BSF.4.21.0003210801280.223-300000@ws-ilmar.ints.ru>
index | next in thread | raw e-mail
[-- Attachment #1 --]
After upgrading from 4.0-current (09.03) to 5.0-current(16.03,17.03) i've
got subj. Machine panics and reboots. And i was not always near
it. Finally i traced it:
Fatal 12 trap: page fault while in kernel mode
fault virtual address = 0x8
fault code = supervisor read, page not present
instruction pointer = 0x8:0xc01843fc
stack pointer = 0x10:0xc026bd64
frame pointer = 0x10:0xc026bd64
code segment = base 0x0, limit 0xfffff, type 0x1b
= DPL 0, pres 1, def32 1, gran 1
processor eflags = interrupt enabled, resume, IOPL = 0
current process = Idle
interrupt mask =
kernel: type 12 trap, code=0
Stopped at arpintr+0x9c: movl 0x8(%ebx),%ecx
trace gave this:
arpint(c022537b,0,10,10,c0220010) at arpintr+0x9c
swi_net_next() at awi_net_next
I'm sending kernel config and dmesg in the attachment. I have INET6 there,
but it is not configured by ifconfig.
What's this and how can i avoid this panics?
[-- Attachment #2 --]
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 5.0-CURRENT #1: Sat Mar 18 10:21:21 MSK 2000
root@ws-ilmar.ints.ru:/usr/src/sys/compile/WS_ILMAR
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium II/Pentium II Xeon/Celeron (367.50-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x660 Stepping = 0
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
real memory = 134152192 (131008K bytes)
avail memory = 127029248 (124052K bytes)
Preloaded elf kernel "kernel" at 0xc02f4000.
Pentium Pro MTRR support enabled
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xf000-0xf00f at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <Intel 82371AB/EB (PIIX4) USB controller> at 7.2 irq 11
chip1: <Intel 82371AB Power management controller> port 0x5000-0x500f at device 7.3 on pci0
pci0: <Matrox MGA Millennium 2064W graphics accelerator> at 9.0 irq 9
rl0: <RealTek 8139 10/100BaseTX> port 0xe400-0xe47f mem 0xe7000000-0xe700007f irq 11 at device 11.0 on pci0
rl0: Ethernet address: 00:c0:df:23:60:e2
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: supplying EUI64: 00:c0:df:ff:fe:23:60:e2
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <keyboard controller (i8042)> at port 0x60-0x6f on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppi0: <Parallel I/O> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
plip0: <PLIP network interface> on ppbus0
unknown0: <ESS ES1868 Plug and Play AudioDrive> at port 0x800-0x807 on isa0
unknown1: <ESS ES1868 Plug and Play AudioDrive> at port 0x220-0x22f,0x388-0x38b,0x330-0x331 irq 5 drq 1,0 on isa0
unknown2: <ESS ES1868 Plug and Play AudioDrive> at port 0x201 on isa0
unknown3: <Generic ESDI/IDE/ATA controller> at port 0x168-0x16f,0x36e-0x36f irq 12 on isa0
ad0: 3077MB <ST33232A> [6253/16/63] at ata0-master using UDMA33
ad2: 19574MB <IBM-DPTA-372050> [39770/16/63] at ata1-master using UDMA33
acd0: CDROM <HITACHI CDR-8335> at ata1-slave using WDMA2
Mounting root from ufs:/dev/wd0s2a
WARNING: / was not properly dismounted
rl0: starting DAD for fe80:0001::02c0:dfff:fe23:60e2
rl0: DAD complete for fe80:0001::02c0:dfff:fe23:60e2 - no duplicates found
[-- Attachment #3 --]
#
# GENERIC -- Generic kernel configuration file for FreeBSD/i386
#
# For more information on this file, please read the handbook section on
# Kernel Configuration Files:
#
# http://www.freebsd.org/handbook/kernelconfig-config.html
#
# The handbook is also available locally in /usr/share/doc/handbook
# if you've installed the doc distribution, otherwise always see the
# FreeBSD World Wide Web server (http://www.FreeBSD.ORG/) for the
# latest information.
#
# An exhaustive list of options and more detailed explanations of the
# device lines is also present in the ./LINT configuration file. If you are
# in doubt as to the purpose or necessity of a line, check first in LINT.
#
# $FreeBSD: src/sys/i386/conf/GENERIC,v 1.247 2000/03/16 09:16:06 n_hibma Exp $
machine i386
cpu I686_CPU
ident WS_ILMAR
maxusers 32
#makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols
#options MATH_EMULATE #Support for x87 emulation
options INET #InterNETworking
options INET6 #IPv6 communications protocols
options FFS #Berkeley Fast Filesystem
options FFS_ROOT #FFS usable as root device [keep this!]
options MFS #Memory Filesystem
#options MD_ROOT #MD is a potential root device
options NFS #Network Filesystem
#options NFS_ROOT #NFS usable as root device, NFS required
options MSDOSFS #MSDOS Filesystem
options CD9660 #ISO 9660 Filesystem
#options CD9660_ROOT #CD-ROM usable as root, CD9660 required
options PROCFS #Process filesystem
options COMPAT_43 #Compatible with BSD 4.3 [KEEP THIS!]
#options SCSI_DELAY=15000 #Delay (in ms) before probing SCSI
options UCONSOLE #Allow users to grab the console
options USERCONFIG #boot -c editor
options VISUAL_USERCONFIG #visual boot -c editor
options KTRACE #ktrace(1) support
options SYSVSHM #SYSV-style shared memory
options SYSVMSG #SYSV-style message queues
options SYSVSEM #SYSV-style semaphores
options P1003_1B #Posix P1003_1B real-time extentions
options _KPOSIX_PRIORITY_SCHEDULING
options ICMP_BANDLIM #Rate limit bad replies
# To make an SMP kernel, the next two are needed
#options SMP # Symmetric MultiProcessor Kernel
#options APIC_IO # Symmetric (APIC) I/O
# Optionally these may need tweaked, (defaults shown):
#options NCPU=2 # number of CPUs
#options NBUS=4 # number of busses
#options NAPIC=1 # number of IO APICs
#options NINTR=24 # number of INTs
device isa
#device eisa
device pci
# Floppy drives
device fdc0 at isa? port IO_FD1 irq 6 drq 2
device fd0 at fdc0 drive 0
device fd1 at fdc0 drive 1
# ATA and ATAPI devices
device ata0 at isa? port IO_WD1 irq 14
device ata1 at isa? port IO_WD2 irq 15
device ata
device atadisk # ATA disk drives
device atapicd # ATAPI CDROM drives
#device atapifd # ATAPI floppy drives
#device atapist # ATAPI tape drives
options ATA_STATIC_ID #Static device numbering
options ATA_ENABLE_ATAPI_DMA #Enable DMA on ATAPI devices
# SCSI Controllers
#device ahb # EISA AHA1742 family
#device ahc # AHA2940 and onboard AIC7xxx devices
#device amd # AMD 53C974 (Teckram DC-390(T))
#device dpt # DPT Smartcache - See LINT for options!
#device isp # Qlogic family
#device ncr # NCR/Symbios Logic
#device sym # NCR/Symbios Logic (newer chipsets)
#device adv0 at isa?
#device adw
#device bt0 at isa?
#device aha0 at isa?
#device aic0 at isa?
# SCSI peripherals
#device scbus # SCSI bus (required)
#device da # Direct Access (disks)
#device sa # Sequential Access (tape etc)
#device cd # CD
#device pass # Passthrough device (direct SCSI access)
# RAID controllers
#device ida # Compaq Smart RAID
#device amr # AMI MegaRAID
#device mlx # Mylex DAC960 family
# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc0 at isa? port IO_KBD
device atkbd0 at atkbdc? irq 1
#device psm0 at atkbdc? irq 12
device vga0 at isa?
# splash screen/screen saver
pseudo-device splash
# syscons is the default console driver, resembling an SCO console
device sc0 at isa?
# Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver
#device vt0 at isa?
#options XSERVER # support for X server on a vt console
#options FAT_CURSOR # start with block cursor
# If you have a ThinkPAD, uncomment this along with the rest of the PCVT lines
#options PCVT_SCANSET=2 # IBM keyboards are non-std
# Floating point support - do not disable.
device npx0 at nexus? port IO_NPX irq 13
# Power management support (see LINT for more options)
device apm0 at nexus? disable flags 0x20 # Advanced Power Management
# PCCARD (PCMCIA) support
#device card
#device pcic0 at isa? irq 10 port 0x3e0 iomem 0xd0000
#device pcic1 at isa? irq 11 port 0x3e2 iomem 0xd4000 disable
# Serial (COM) ports
device sio0 at isa? port IO_COM1 flags 0x10 irq 4
device sio1 at isa? port IO_COM2 irq 3
#device sio2 at isa? disable port IO_COM3 irq 5
#device sio3 at isa? disable port IO_COM4 irq 9
# Parallel port
device ppc0 at isa? irq 7
device ppbus # Parallel port bus (required)
device lpt # Printer
device plip # TCP/IP over parallel
device ppi # Parallel port interface device
#device vpo # Requires scbus and da
# PCI Ethernet NICs.
#device de # DEC/Intel DC21x4x (``Tulip'')
#device fxp # Intel EtherExpress PRO/100B (82557, 82558)
#device tx # SMC 9432TX (83c170 ``EPIC'')
#device vx # 3Com 3c590, 3c595 (``Vortex'')
#device wx # Intel Gigabit Ethernet Card (``Wiseman'')
# PCI Ethernet NICs that use the common MII bus controller code.
device miibus # MII bus support
#device dc # DEC/Intel 21143 and various workalikes
device rl # RealTek 8129/8139
#device sf # Adaptec AIC-6915 (``Starfire'')
#device sis # Silicon Integrated Systems SiS 900/SiS 7016
#device ste # Sundance ST201 (D-Link DFE-550TX)
#device tl # Texas Instruments ThunderLAN
#device vr # VIA Rhine, Rhine II
#device wb # Winbond W89C840F
#device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
# ISA Ethernet NICs.
#device ed0 at isa? port 0x280 irq 10 iomem 0xd8000
#device ex
#device ep
# WaveLAN/IEEE 802.11 wireless NICs. Note: the WaveLAN/IEEE really
# exists only as a PCMCIA device, so there is no ISA attatement needed
# and resources will always be dynamically assigned by the pccard code.
#device wi
# Aironet 4500/4800 802.11 wireless NICs. Note: the declaration below will
# work for PCMCIA and PCI cards, as well as ISA cards set to ISA PnP
# mode (the factory default). If you set the switches on your ISA
# card for a manually chosen I/O address and IRQ, you must specify
# those paremeters here.
#device an
# The probe order of these is presently determined by i386/isa/isa_compat.c.
#device ie0 at isa? port 0x300 irq 10 iomem 0xd0000
#device fe0 at isa? port 0x300
#device le0 at isa? port 0x300 irq 5 iomem 0xd0000
#device lnc0 at isa? port 0x280 irq 10 drq 0
#device cs0 at isa? port 0x300
#device sn0 at isa? port 0x300 irq 10
# requires PCCARD (PCMCIA) support to be activated
#device xe0 at isa?
# Pseudo devices - the number indicates how many units to allocated.
pseudo-device loop # Network loopback
pseudo-device ether # Ethernet support
#pseudo-device sl 1 # Kernel SLIP
#pseudo-device ppp 1 # Kernel PPP
pseudo-device tun # Packet tunnel.
pseudo-device pty # Pseudo-ttys (telnet etc)
pseudo-device md # Memory "disks"
pseudo-device gif 4 # IPv6 and IPv4 tunneling
pseudo-device faith 1 # IPv6-to-IPv4 relaying (translation)
# The `bpf' pseudo-device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
pseudo-device bpf #Berkeley packet filter
# USB support
#device uhci # UHCI PCI->USB interface
#device ohci # OHCI PCI->USB interface
#device usb # USB Bus (required)
#device ugen # Generic
#device uhid # "Human Interface Devices"
#device ukbd # Keyboard
#device ulpt # Printer
#device umass # Disks/Mass storage - Requires scbus and da
#device ums # Mouse
#device urio # Diamond Rio 500 MP3 player
# USB Ethernet, requires mii
#device aue # ADMtek USB ethernet
#device cue # CATC USB ethernet
#device kue # Kawasaki LSI USB ethernet
#
# Enable the kernel debugger.
#
options DDB
#
# Don't drop into DDB for a panic. Intended for unattended operation
# where you may want to drop to DDB from the console, but still want
# the machine to recover from a panic
#
#options DDB_UNATTENDED
#
# If using GDB remote mode to debug the kernel, there's a non-standard
# extension to the remote protocol that can be used to use the serial
# port as both the debugging port and the system console. It's non-
# standard and you're on your own if you enable it. See also the
# "remotechat" variables in the FreeBSD specific version of gdb.
#
#options GDB_REMOTE_CHAT
#
# KTRACE enables the system-call tracing facility ktrace(2).
#
options KTRACE #kernel tracing
#
# The INVARIANTS option is used in a number of source files to enable
# extra sanity checking of internal structures. This support is not
# enabled by default because of the extra time it would take to check
# for these conditions, which can only occur as a result of
# programming errors.
#
options INVARIANTS
#
# The INVARIANT_SUPPORT option makes us compile in support for
# verifying some of the internal structures. It is a prerequisite for
# 'INVARIANTS', as enabling 'INVARIANTS' will make these functions be
# called. The intent is that you can set 'INVARIANTS' for single
# source files (by changing the source file or specifying it on the
# command line) if you have 'INVARIANT_SUPPORT' enabled.
#
options INVARIANT_SUPPORT
#
# The DIAGNOSTIC option is used to enable extra debugging information
# from some parts of the kernel. As this makes everything more noisy,
# it is disabled by default.
#
options DIAGNOSTIC
#
# PERFMON causes the driver for Pentium/Pentium Pro performance counters
# to be compiled. See perfmon(4) for more information.
#
options PERFMON
help
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.4.21.0003210801280.223-300000>