Date: Fri, 22 Jun 2001 16:54:55 -0700 (PDT) From: jimmie james <h2g2_jimmiejaz@yahoo.com> To: freebsd-mobile@freebsd.org Subject: PCCARD troubles Message-ID: <20010622235455.8956.qmail@web13403.mail.yahoo.com>
next in thread | raw e-mail | index | archive | help
First time poster, long time reader. HP OmniBook 5700CT running FreeBSD 4.3. PCCARD in question USRobotics Megahertz XJ4336(I know, upgrade, but $$ is tight) I can't seem to be able to comminucate with it. After the 7th install I still can't get it going(It works out of the box with slackware 7.1) here is the dmesg, and the pccardc dumpcis any help, would be greatly appericated and if you're ever in the St. Louis area, a(1-3-a dozen) beer is on me. sorry about the format, I had to cp it to a windows box.Copyright (c) 1992-2001 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 4.3-RELEASE #0: Sat Apr 21 10:54:49 GMT 2001 jkh@narf.osd.bsdi.com:/usr/src/sys/compile/GENERIC Timecounter "i8254" frequency 1193182 Hz CPU: Pentium/P55C (166.66-MHz 586-class CPU) Origin = "GenuineIntel" Id = 0x543 Stepping = 3 Features=0x8001bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,MMX> real memory = 50331648 (49152K bytes) config> di lnc0 config> di ie0 config> di fe0 config> di ed0 config> di cs0 config> di bt0 config> di aic0 config> di aha0 config> di adv0 config> en pcic1 config> po pcic1 0x3e2 config> ir pcic1 0 config> iom pcic1 0xd4000 config> f pcic1 0 config> en sio3 config> po sio3 0x2e8 config> ir sio3 9 config> f sio3 0 config> en sio2 config> po sio2 0x3e8 config> ir sio2 5 config> f sio2 0 config> q avail memory = 44646400 (43600K bytes) Preloaded elf kernel "kernel" at 0xc044d000. Preloaded userconfig_script "/boot/kernel.conf" at 0xc044d09c. Intel Pentium detected, installing workaround for F00F bug md0: Malloc disk npx0: <math processor> on motherboard npx0: INT 16 interface pcib0: <Host to PCI bridge> on motherboard pci0: <PCI bus> on pcib0 isab0: <PCI to ISA bridge (vendor=1045 device=c558)> at device 1.0 on pci0 isa0: <ISA bus> on isab0 pci0: <Chips & Technologies 65554 SVGA controller> at 2.0 pcic-pci0: <TI PCI-1131 PCI-CardBus Bridge> at device 3.0 on pci0 pcic-pci0: TI113X PCI Config Reg: [speaker enable][CSC serial isa irq] pcic-pci1: <TI PCI-1131 PCI-CardBus Bridge> at device 3.1 on pci0 pcic-pci1: TI113X PCI Config Reg: [speaker enable][CSC serial isa irq] atapci0: <Generic PCI ATA controller> port 0x3000-0x300f at device 20.0 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: model Generic PS/2 mouse, device ID 0 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> pcic0: <VLSI 82C146> at port 0x3e0 iomem 0xd0000 on isa0 pcic0: Polling mode pccard0: <PC Card bus -- kludge version> on pcic0 pccard1: <PC Card bus -- kludge version> on pcic0 sio0: configured irq 4 not in bitmap of probed irqs 0 sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 8250 sio1: configured irq 3 not in bitmap of probed irqs 0 sio2: configured irq 5 not in bitmap of probed irqs 0 sio3: configured irq 9 not in bitmap of probed irqs 0 ppc0: parallel port not found. ad0: 2067MB <TOSHIBA MK2103MAV> [4200/16/63] at ata0-master PIO4 acd0: CDROM <TOSHIBA CD-ROM XM-1602B> at ata1-master using PIO4 Mounting root from ufs:/dev/ad0s1a pccard: card inserted, slot 0 ppp0: IPv6 not supported ppp0: IPv6 not supported sio4 at port 0x2f8-0x2ff irq 3 slot 0 on pccard0 sio4: type 16550A Waiting (max 60 seconds) for system process `bufdaemon' to stop...stopped Waiting (max 60 seconds) for system process `syncer' to stop...stopped syncing disks... 4 4 3 done Uptime: 21m48s Rebooting... Copyright (c) 1992-2001 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 4.3-RELEASE #0: Sat Apr 21 10:54:49 GMT 2001 jkh@narf.osd.bsdi.com:/usr/src/sys/compile/GENERIC Timecounter "i8254" frequency 1193182 Hz CPU: Pentium/P55C (166.66-MHz 586-class CPU) Origin = "GenuineIntel" Id = 0x543 Stepping = 3 Features=0x8001bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,MMX> real memory = 50331648 (49152K bytes) config> di lnc0 config> di ie0 config> di fe0 config> di ed0 config> di cs0 config> di bt0 config> di aic0 config> di aha0 config> di adv0 config> en pcic1 config> po pcic1 0x3e2 config> ir pcic1 0 config> iom pcic1 0xd4000 config> f pcic1 0 config> en sio3 config> po sio3 0x2e8 config> ir sio3 9 config> f sio3 0 config> en sio2 config> po sio2 0x3e8 config> ir sio2 5 config> f sio2 0 config> q avail memory = 44646400 (43600K bytes) Preloaded elf kernel "kernel" at 0xc044d000. Preloaded userconfig_script "/boot/kernel.conf" at 0xc044d09c. Intel Pentium detected, installing workaround for F00F bug md0: Malloc disk npx0: <math processor> on motherboard npx0: INT 16 interface pcib0: <Host to PCI bridge> on motherboard pci0: <PCI bus> on pcib0 isab0: <PCI to ISA bridge (vendor=1045 device=c558)> at device 1.0 on pci0 isa0: <ISA bus> on isab0 pci0: <Chips & Technologies 65554 SVGA controller> at 2.0 pcic-pci0: <TI PCI-1131 PCI-CardBus Bridge> at device 3.0 on pci0 pcic-pci0: TI113X PCI Config Reg: [speaker enable][CSC serial isa irq] pcic-pci1: <TI PCI-1131 PCI-CardBus Bridge> at device 3.1 on pci0 pcic-pci1: TI113X PCI Config Reg: [speaker enable][CSC serial isa irq] atapci0: <Generic PCI ATA controller> port 0x3000-0x300f at device 20.0 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: model Generic PS/2 mouse, device ID 0 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> pcic0: <VLSI 82C146> at port 0x3e0 iomem 0xd0000 on isa0 pcic0: Polling mode pccard0: <PC Card bus -- kludge version> on pcic0 pccard1: <PC Card bus -- kludge version> on pcic0 sio0: configured irq 4 not in bitmap of probed irqs 0 sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 8250 sio1: configured irq 3 not in bitmap of probed irqs 0 sio2: configured irq 5 not in bitmap of probed irqs 0 sio3: configured irq 9 not in bitmap of probed irqs 0 ppc0: parallel port not found. ad0: 2067MB <TOSHIBA MK2103MAV> [4200/16/63] at ata0-master PIO4 acd0: CDROM <TOSHIBA CD-ROM XM-1602B> at ata1-master using PIO4 Mounting root from ufs:/dev/ad0s1a pccard: card inserted, slot 0 Code 128 not found Code 128 not found code Unknown ignored Configuration data for card in slot 0 Tuple #1, code = 0x1 (Common memory descriptor), length = 3 000: 00 00 ff Common memory device information: Device number 1, type No device, WPS = OFF Speed = No speed, Memory block size = 512b, 1 units Tuple #2, code = 0x15 (Version 1 info), length = 51 000: 05 00 4d 65 67 61 68 65 72 74 7a 00 58 4a 34 33 010: 33 36 2d 43 43 34 33 33 36 00 56 2e 33 34 2b 20 020: 44 61 74 61 2f 46 61 78 2f 43 65 6c 6c 2f 56 6f 030: 78 00 ff Version = 5.0, Manuf = [Megahertz], card vers = [XJ4336-CC4336] Addit. info = [V.34+ Data/Fax/Cell/Vox] Tuple #3, code = 0x20 (Manufacturer ID), length = 4 000: 02 01 27 00 PCMCIA ID = 0x102, OEM ID = 0x27 Tuple #4, code = 0x1a (Configuration map), length = 5 000: 01 23 00 03 03 Reg len = 2, config register addr = 0x300, last config = 0x23 Registers: XX------ Tuple #5, code = 0x1b (Configuration entry), length = 16 000: e0 41 99 49 55 26 25 aa 60 f8 03 07 30 ff ff 28 Config index = 0x20(default) Interface byte = 0x41 (I/O) +RDY/-BSY active Vcc pwr: Nominal operating supply voltage: 5 x 1V Continuous supply current: 2 x 100mA Power down supply current: 2 x 10mA Card decodes 10 address lines, 8 Bit I/O only I/O address # 1: block start = 0x3f8 block length = 0x8 IRQ modes: Level IRQs: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Max twin cards = 0 Misc attr: (Audio-BVD2) (Power down supported) Tuple #6, code = 0x1b (Configuration entry), length = 7 000: 21 08 aa 60 f8 02 07 Config index = 0x21 Card decodes 10 address lines, 8 Bit I/O only I/O address # 1: block start = 0x2f8 block length = 0x8 Tuple #7, code = 0x1b (Configuration entry), length = 7 000: 22 08 aa 60 e8 03 07 Config index = 0x22 Card decodes 10 address lines, 8 Bit I/O only I/O address # 1: block start = 0x3e8 block length = 0x8 Tuple #8, code = 0x1b (Configuration entry), length = 7 000: 23 08 aa 60 e8 02 07 Config index = 0x23 Card decodes 10 address lines, 8 Bit I/O only I/O address # 1: block start = 0x2e8 block length = 0x8 Tuple #9, code = 0x21 (Functional ID), length = 2 000: 02 01 Serial port/modem - POST initialize Tuple #10, code = 0x22 (Functional EXT), length = 4 000: 00 02 0f 7c Serial interface extension: 16550 UART, Parity - Space,Mark,Odd,Even Data bit - 7bit,8bit, Stop bit - 1bit,1.5bit,2bit Tuple #11, code = 0x22 (Functional EXT), length = 9 000: 01 1f 0d 00 03 00 00 03 00 Modem interface capabilities: Tuple #12, code = 0x22 (Functional EXT), length = 12 000: 02 06 00 3f 1c 03 03 0f 07 00 02 b5 Data modem services available: Tuple #13, code = 0x22 (Functional EXT), length = 8 000: 13 06 00 0f 00 02 00 b5 Fax1/modem services available: Tuple #14, code = 0x22 (Functional EXT), length = 8 000: 23 06 00 0f 00 02 00 b5 Fax2/modem services available: Tuple #15, code = 0x22 (Functional EXT), length = 13 000: 84 00 06 0b 02 07 14 00 08 00 00 01 00 Voice services available: Tuple #16, code = 0x0 (Null tuple), length = 10 000: 02 01 27 00 0d 00 00 00 00 ff Tuple #17, code = 0x14 (No link), length = 0 Tuple #18, code = 0xff (Terminator), length = 0 2 slots found __________________________________________________ Do You Yahoo!? Get personalized email addresses from Yahoo! Mail http://personal.mail.yahoo.com/ To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-mobile" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20010622235455.8956.qmail>