Date: Sun, 17 Apr 2016 12:05:09 +0300 From: Pavel Timofeev <timp87@gmail.com> To: freebsd-current@freebsd.org Subject: OCZ ssdpx-1rvd0120 REVODRIVE support Message-ID: <CAAoTqftw--ks3BDZ0iCfQ25fb%2BYGrr9VknjVSbUQ1kFSLGdX-A@mail.gmail.com>
next in thread | raw e-mail | index | archive | help
[-- Attachment #1 --]
HI! I've recently got a SSD device. Yes, not a disk, but a device.
It's called, i. e. one of the first REVODRIVEs.
It's a PCI-express card with two embedded ssd disks about ~ 55GB size.
And it's a raid card. Fake software raid. You can set it up as a
RAID0, RAID1, etc and a CONCATENATION. No way to leave it unconfigured
or set it as JBOD or something else.
You just won't be able to boot from this device in that case.
So, I tried to install FreeBSD on it. Actually two fbsd version:
FreeBSD 10.3-RELEASE amd64 and FreeBSD-CURRENT amd64 based on r297561
. .
I used RAID0, RAID1 and CONCATENATION raid configurations and UFS and
ZFS (stripe) filesystems. The deivce is seen as raid/r0 and I
installed fbsd on it.
Here is the result of different attemps.
FreeBSD 11-CURRENT r297561 amd64
RAID0
UFS
MBR - during installation I immediately get 'unknown error -559038242'
GPT - the same and 'Error installing partcode on r0p1' message
ZFS
MBR - 'Invalid argument' during installation.
GPT - 'Invalid argument' during installation.
RAID1
UFS
MBR - installs and boots w/o problem
GPT - installs and boots w/o problem
ZFS
MBR - 'Invalid argument' during installation.
GPT - 'Invalid argument' during installation.
CONCATENATION
UFS
MBR - 'unknown error -559038242' during installation
GPT - 'unknown error -559038242' during installation
ZFS
MBR - 'Invalid argument' during installation.
GPT - 'Invalid argument' during installation.
FreeBSD 10.3-RELEASE amd64
RAID0
UFS
MBR - installs and boots w/o problem
GPT - installs, but doesn't boot. I can see on the screen:
gptboot: error lba 1280
gptboot: No /boot/loader on 0:ad(0p2)
gptboot: No /boot/kernel/kernel on 0:ad(0p2)
ZFS
MBR - 'Invalid argument' during installation.
GPT - 'Invalid argument' during installation.
RAID1
UFS
MBR - installs and boots w/o problem
GPT - installs and boots w/o problem
ZFS
MBR - 'Invalid argument' during installation.
GPT - hangs during installation
CONCATENATION
UFS
MBR - installs, but panics during boot
GPT - the same, but also I see the following messages on the
screen durin boot
gpterror 1 lba 234458719
unable to read gpt header
ZFS
MBR - 'Invalid argument' during installation.
GPT - 'Invalid argument' during installation.
Also I've attached dmesg and 'geom disk list' output.
I'm ready to try some patches and help to solve this problem!
[-- Attachment #2 --]
Copyright (c) 1992-2016 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 11.0-CURRENT #0 r297561: Mon Apr 4 22:42:00 MSK 2016
timp@fbsd11:/usr/obj/usr/src/sys/GENERIC amd64
FreeBSD clang version 3.8.0 (tags/RELEASE_380/final 262564) (based on LLVM 3.8.0)
WARNING: WITNESS option enabled, expect reduced performance.
VT(vga): resolution 640x480
CPU: Intel(R) Core(TM) i3-2120 CPU @ 3.30GHz (3292.59-MHz K8-class CPU)
Origin="GenuineIntel" Id=0x206a7 Family=0x6 Model=0x2a Stepping=7
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x1d9ae3bf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,POPCNT,TSCDLT,XSAVE,OSXSAVE,AVX>
AMD Features=0x28100800<SYSCALL,NX,RDTSCP,LM>
AMD Features2=0x1<LAHF>
XSAVE Features=0x1<XSAVEOPT>
VT-x: PAT,HLT,MTF,PAUSE,EPT,UG,VPID
TSC: P-state invariant, performance statistics
real memory = 8589934592 (8192 MB)
avail memory = 8207171584 (7826 MB)
Event timer "LAPIC" quality 600
ACPI APIC Table: <ALASKA A M I>
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
FreeBSD/SMP: 1 package(s) x 2 core(s) x 2 hardware threads
ioapic0 <Version 2.0> irqs 0-23 on motherboard
random: entropy device external interface
kbd1 at kbdmux0
netmap: loaded module
module_register_init: MOD_LOAD (vesa, 0xffffffff80f05eb0, 0) error 19
vtvga0: <VT VGA driver> on motherboard
cryptosoft0: <software crypto> on motherboard
acpi0: <ALASKA A M I> on motherboard
acpi0: Power Button (fixed)
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
cpu2: <ACPI CPU> on acpi0
cpu3: <ACPI CPU> on acpi0
hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 950
Event timer "HPET" frequency 14318180 Hz quality 550
Event timer "HPET1" frequency 14318180 Hz quality 440
Event timer "HPET2" frequency 14318180 Hz quality 440
Event timer "HPET3" frequency 14318180 Hz quality 440
Event timer "HPET4" frequency 14318180 Hz quality 440
atrtc0: <AT realtime clock> port 0x70-0x77 irq 8 on acpi0
atrtc0: Warning: Couldn't map I/O.
Event timer "RTC" frequency 32768 Hz quality 0
attimer0: <AT timer> port 0x40-0x43,0x50-0x53 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0xe000-0xe0ff mem 0xe0000000-0xefffffff,0xf7e00000-0xf7e3ffff irq 16 at device 0.0 on pci1
vgapci0: Boot video device
hdac0: <ATI (0xaab0) HDA Controller> mem 0xf7e60000-0xf7e63fff irq 17 at device 0.1 on pci1
hdac0: hdac_get_capabilities: Invalid corb size (0)
device_attach: hdac0 attach returned 6
xhci0: <Intel Panther Point USB 3.0 controller> mem 0xf7f00000-0xf7f0ffff irq 16 at device 20.0 on pci0
xhci0: 32 bytes context size, 64-bit DMA
xhci0: Port routing mask set to 0xffffffff
usbus0 on xhci0
pci0: <simple comms> at device 22.0 (no driver attached)
ehci0: <Intel Panther Point USB 2.0 controller> mem 0xf7f18000-0xf7f183ff irq 16 at device 26.0 on pci0
usbus1: EHCI version 1.0
usbus1 on ehci0
hdac0: <Intel Panther Point HDA Controller> mem 0xf7f10000-0xf7f13fff irq 22 at device 27.0 on pci0
pcib2: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pci2: <ACPI PCI bus> on pcib2
pcib3: <PCI-PCI bridge> irq 16 at device 0.0 on pci2
pci3: <PCI bus> on pcib3
siis0: <SiI3124 SATA controller> port 0xd000-0xd00f mem 0xf7d88000-0xf7d8807f,0xf7d80000-0xf7d87fff irq 16 at device 0.0 on pci3
siisch0: <SIIS channel> at channel 0 on siis0
siisch1: <SIIS channel> at channel 1 on siis0
siisch2: <SIIS channel> at channel 2 on siis0
siisch3: <SIIS channel> at channel 3 on siis0
pcib4: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0
pci4: <ACPI PCI bus> on pcib4
ahci0: <ASMedia ASM1061 AHCI SATA controller> port 0xc050-0xc057,0xc040-0xc043,0xc030-0xc037,0xc020-0xc023,0xc000-0xc01f mem 0xf7c00000-0xf7c001ff irq 16 at device 0.0 on pci4
ahci0: AHCI v1.20 with 2 6Gbps ports, Port Multiplier supported
ahcich0: <AHCI channel> at channel 0 on ahci0
ahcich1: <AHCI channel> at channel 1 on ahci0
pcib5: <ACPI PCI-PCI bridge> irq 17 at device 28.5 on pci0
pci5: <ACPI PCI bus> on pcib5
re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F/G PCIe Gigabit Ethernet> port 0xb000-0xb0ff mem 0xf0004000-0xf0004fff,0xf0000000-0xf0003fff irq 17 at device 0.0 on pci5
re0: Using 1 MSI-X message
re0: Chip rev. 0x2c800000
re0: MAC rev. 0x00100000
miibus0: <MII bus> on re0
rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus0
rgephy0: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow
re0: Using defaults for TSO: 65518/35/2048
re0: Ethernet address: bc:5f:f4:37:43:ef
re0: netmap queues/slots: TX 1/256, RX 1/256
ehci1: <Intel Panther Point USB 2.0 controller> mem 0xf7f17000-0xf7f173ff irq 23 at device 29.0 on pci0
usbus2: EHCI version 1.0
usbus2 on ehci1
pcib6: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci6: <ACPI PCI bus> on pcib6
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
ahci1: <Intel Panther Point AHCI SATA controller> port 0xf070-0xf077,0xf060-0xf063,0xf050-0xf057,0xf040-0xf043,0xf020-0xf03f mem 0xf7f16000-0xf7f167ff irq 19 at device 31.2 on pci0
ahci1: AHCI v1.30 with 6 6Gbps ports, Port Multiplier not supported
ahcich2: <AHCI channel> at channel 0 on ahci1
ahcich3: <AHCI channel> at channel 1 on ahci1
ahcich4: <AHCI channel> at channel 2 on ahci1
ahcich5: <AHCI channel> at channel 3 on ahci1
ahcich6: <AHCI channel> at channel 4 on ahci1
ahcich7: <AHCI channel> at channel 5 on ahci1
ahciem0: <AHCI enclosure management bridge> on ahci1
acpi_button0: <Power Button> on acpi0
ppc1: <Parallel port> port 0x378-0x37f,0x778-0x77f irq 5 drq 3 on acpi0
ppc1: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc1: FIFO with 16/16/9 bytes threshold
ppbus0: <Parallel port bus> on ppc1
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xcffff,0xd0000-0xd4fff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
ppc0: cannot reserve I/O port range
est0: <Enhanced SpeedStep Frequency Control> on cpu0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
est2: <Enhanced SpeedStep Frequency Control> on cpu2
est3: <Enhanced SpeedStep Frequency Control> on cpu3
(noperiph:siisch0:0:-1:ffffffff): rescan already queued
(noperiph:siisch1:0:-1:ffffffff): rescan already queued
usbus0: 5.0Gbps Super Speed USB v3.0
Timecounters tick every 1.000 msec
hdacc0: <Realtek ALC662 HDA CODEC> at cad 0 on hdac0
hdaa0: <Realtek ALC662 Audio Function Group> at nid 1 on hdacc0
pcm0: <Realtek ALC662 (Rear Analog)> at nid 20 and 24,26 on hdaa0
pcm1: <Realtek ALC662 (Front Analog)> at nid 27 and 25 on hdaa0
usbus1: 480Mbps High Speed USB v2.0
usbus2: 480Mbps High Speed USB v2.0
ugen0.1: <0x8086> at usbus0
uhub0: <0x8086 XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
ugen2.1: <Intel> at usbus2
uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
ugen1.1: <Intel> at usbus1
uhub2: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
ses0 at ahciem0 bus 0 scbus12 target 0 lun 0
ses0: <AHCI SGPIO Enclosure 1.00 0001> SEMB S-E-S 2.00 device
ses0: SEMB SES Device
ada0 at siisch0 bus 0 scbus0 target 0 lun 0
ada0: <OCZ-REVODRIVE 1.37> ATA8-ACS SATA 2.x device
ada0: Serial Number OCZ-4I0B17Q0H2K7990M
ada0: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada0: Command Queueing enabled
ada0: 57241MB (117231408 512 byte sectors)
ada1 at siisch1 bus 0 scbus1 target 0 lun 0
ada1: <OCZ-REVODRIVE 1.37> ATA8-ACS SATA 2.x device
ada1: Serial Number OCZ-513Y931NLS8L79KY
ada1: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada1: Command Queueing enabled
ada1: 57241MB (117231408 512 byte sectors)
SMP: AP CPU #1 Launched!
SMP: AP CPU #3 Launched!
SMP: AP CPU #2 Launched!
GEOM_RAID: SiI-160406211929: Array SiI-160406211929 created.
Timecounter "TSC-low" frequency 1646296956 Hz quality 1000
WARNING: WITNESS option enabled, expect reduced performance.
GEOM_RAID: SiI-160406211929: Disk ada0 state changed from NONE to ACTIVE.
GEOM_RAID: SiI-160406211929: Subdisk SiI Concatenatio:0-ada0 state changed from NONE to STALE.
Trying to mount root from ufs:/dev/ufs/FreeBSD_Install [ro,noatime]...
GEOM_RAID: SiI-160406211929: Disk ada1 state changed from NONE to ACTIVE.
GEOM_RAID: SiI-160406211929: Subdisk SiI Concatenatio:1-ada1 state changed from NONE to STALE.
GEOM_RAID: SiI-160406211929: Array started.
GEOM_RAID: SiI-160406211929: Subdisk SiI Concatenatio:0-ada0 state changed from STALE to ACTIVE.
GEOM_RAID: SiI-160406211929: Subdisk SiI Concatenatio:1-ada1 state changed from STALE to ACTIVE.
GEOM_RAID: SiI-160406211929: Volume SiI Concatenatio state changed from STARTING to OPTIMAL.
Root mount waiting for: GRAID usbus2 usbus1 usbus0
GEOM_RAID: SiI-160406211929: Provider raid/r0 for volume SiI Concatenatio created.
uhub0: 8 ports with 8 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
Root mount waiting for: usbus2 usbus1 usbus0
ugen0.2: <vendor 0x0409> at usbus0
uhub3: <vendor 0x0409 product 0x005a, class 9/0, rev 2.00/1.00, addr 1> on usbus0
ugen2.2: <vendor 0x8087> at usbus2
uhub4: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on usbus2
ugen1.2: <vendor 0x8087> at usbus1
uhub5: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on usbus1
uhub3: 4 ports with 4 removable, self powered
Root mount waiting for: usbus2 usbus1 usbus0
ugen0.3: <vendor 0x0402> at usbus0
uhub4: 6 ports with 6 removable, self powered
uhub5: 6 ports with 6 removable, self powered
Root mount waiting for: usbus2 usbus1 usbus0
ugen0.4: <vendor 0x04d9> at usbus0
ukbd0: <vendor 0x04d9 USB Keyboard, class 0/0, rev 1.10/3.10, addr 3> on usbus0
kbd2 at ukbd0
ugen2.3: <vendor 0x093a> at usbus2
Root mount waiting for: usbus1
ugen1.3: <Kingston> at usbus1
umass0: <Kingston DataTravelerMini, class 0/0, rev 2.00/1.00, addr 3> on usbus1
umass0: SCSI over Bulk-Only; quirks = 0xc100
umass0:13:0: Attached to scbus13
da0 at umass-sim0 bus 0 scbus13 target 0 lun 0
da0: <Kingston DataTravelerMini PMAP> Removable Direct Access SCSI device
da0: Serial Number 5B7410730044
da0: 40.000MB/s transfers
da0: 1968MB (4030464 512 byte sectors)
da0: quirks=0x2<NO_6_BYTE>
GEOM: da0: the secondary GPT header is not in the last LBA.
GEOM: diskid/DISK-5B7410730044: the secondary GPT header is not in the last LBA.
mountroot: waiting for device /dev/ufs/FreeBSD_Install...
GEOM: diskid/DISK-5B7410730044: the secondary GPT header is not in the last LBA.
random: unblocking device.
re0: link state changed to UP
ums0: <vendor 0x093a USB OPTICAL MOUSE, class 0/0, rev 1.10/1.00, addr 3> on usbus2
ums0: 5 buttons and [XYZT] coordinates ID=0
uhid0: <vendor 0x04d9 USB Keyboard, class 0/0, rev 1.10/3.10, addr 3> on usbus0
[-- Attachment #3 --]
Geom name: ada0
Providers:
1. Name: ada0
Mediasize: 60022480896 (56G)
Sectorsize: 512
Mode: r1w1e1
descr: OCZ-REVODRIVE
lunid: 5e83a97f837bd07b
ident: OCZ-4I0B17Q0H2K7990M
rotationrate: 0
fwsectors: 63
fwheads: 16
Geom name: ada1
Providers:
1. Name: ada1
Mediasize: 60022480896 (56G)
Sectorsize: 512
Mode: r1w1e1
descr: OCZ-REVODRIVE
lunid: 5e83a97ff2f711c3
ident: OCZ-513Y931NLS8L79KY
rotationrate: 0
fwsectors: 63
fwheads: 16
Geom name: da0
Providers:
1. Name: da0
Mediasize: 2063597568 (1.9G)
Sectorsize: 512
Mode: r1w0e1
descr: Kingston DataTravelerMini
ident: 5B7410730044
rotationrate: unknown
fwsectors: 63
fwheads: 255
[-- Attachment #4 --]
Copyright (c) 1992-2016 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 11.0-CURRENT #0 r297561: Mon Apr 4 22:42:00 MSK 2016
timp@fbsd11:/usr/obj/usr/src/sys/GENERIC amd64
FreeBSD clang version 3.8.0 (tags/RELEASE_380/final 262564) (based on LLVM 3.8.0)
WARNING: WITNESS option enabled, expect reduced performance.
VT(vga): resolution 640x480
CPU: Intel(R) Core(TM) i3-2120 CPU @ 3.30GHz (3292.59-MHz K8-class CPU)
Origin="GenuineIntel" Id=0x206a7 Family=0x6 Model=0x2a Stepping=7
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x1d9ae3bf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,POPCNT,TSCDLT,XSAVE,OSXSAVE,AVX>
AMD Features=0x28100800<SYSCALL,NX,RDTSCP,LM>
AMD Features2=0x1<LAHF>
XSAVE Features=0x1<XSAVEOPT>
VT-x: PAT,HLT,MTF,PAUSE,EPT,UG,VPID
TSC: P-state invariant, performance statistics
real memory = 8589934592 (8192 MB)
avail memory = 8207171584 (7826 MB)
Event timer "LAPIC" quality 600
ACPI APIC Table: <ALASKA A M I>
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
FreeBSD/SMP: 1 package(s) x 2 core(s) x 2 hardware threads
ioapic0 <Version 2.0> irqs 0-23 on motherboard
random: entropy device external interface
kbd1 at kbdmux0
netmap: loaded module
module_register_init: MOD_LOAD (vesa, 0xffffffff80f05eb0, 0) error 19
vtvga0: <VT VGA driver> on motherboard
cryptosoft0: <software crypto> on motherboard
acpi0: <ALASKA A M I> on motherboard
acpi0: Power Button (fixed)
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
cpu2: <ACPI CPU> on acpi0
cpu3: <ACPI CPU> on acpi0
hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 950
Event timer "HPET" frequency 14318180 Hz quality 550
Event timer "HPET1" frequency 14318180 Hz quality 440
Event timer "HPET2" frequency 14318180 Hz quality 440
Event timer "HPET3" frequency 14318180 Hz quality 440
Event timer "HPET4" frequency 14318180 Hz quality 440
atrtc0: <AT realtime clock> port 0x70-0x77 irq 8 on acpi0
atrtc0: Warning: Couldn't map I/O.
Event timer "RTC" frequency 32768 Hz quality 0
attimer0: <AT timer> port 0x40-0x43,0x50-0x53 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0xe000-0xe0ff mem 0xe0000000-0xefffffff,0xf7e00000-0xf7e3ffff irq 16 at device 0.0 on pci1
vgapci0: Boot video device
hdac0: <ATI (0xaab0) HDA Controller> mem 0xf7e60000-0xf7e63fff irq 17 at device 0.1 on pci1
hdac0: hdac_get_capabilities: Invalid corb size (0)
device_attach: hdac0 attach returned 6
xhci0: <Intel Panther Point USB 3.0 controller> mem 0xf7f00000-0xf7f0ffff irq 16 at device 20.0 on pci0
xhci0: 32 bytes context size, 64-bit DMA
xhci0: Port routing mask set to 0xffffffff
usbus0 on xhci0
pci0: <simple comms> at device 22.0 (no driver attached)
ehci0: <Intel Panther Point USB 2.0 controller> mem 0xf7f18000-0xf7f183ff irq 16 at device 26.0 on pci0
usbus1: EHCI version 1.0
usbus1 on ehci0
hdac0: <Intel Panther Point HDA Controller> mem 0xf7f10000-0xf7f13fff irq 22 at device 27.0 on pci0
pcib2: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pci2: <ACPI PCI bus> on pcib2
pcib3: <PCI-PCI bridge> irq 16 at device 0.0 on pci2
pci3: <PCI bus> on pcib3
siis0: <SiI3124 SATA controller> port 0xd000-0xd00f mem 0xf7d88000-0xf7d8807f,0xf7d80000-0xf7d87fff irq 16 at device 0.0 on pci3
siisch0: <SIIS channel> at channel 0 on siis0
siisch1: <SIIS channel> at channel 1 on siis0
siisch2: <SIIS channel> at channel 2 on siis0
siisch3: <SIIS channel> at channel 3 on siis0
pcib4: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0
pci4: <ACPI PCI bus> on pcib4
ahci0: <ASMedia ASM1061 AHCI SATA controller> port 0xc050-0xc057,0xc040-0xc043,0xc030-0xc037,0xc020-0xc023,0xc000-0xc01f mem 0xf7c00000-0xf7c001ff irq 16 at device 0.0 on pci4
ahci0: AHCI v1.20 with 2 6Gbps ports, Port Multiplier supported
ahcich0: <AHCI channel> at channel 0 on ahci0
ahcich1: <AHCI channel> at channel 1 on ahci0
pcib5: <ACPI PCI-PCI bridge> irq 17 at device 28.5 on pci0
pci5: <ACPI PCI bus> on pcib5
re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F/G PCIe Gigabit Ethernet> port 0xb000-0xb0ff mem 0xf0004000-0xf0004fff,0xf0000000-0xf0003fff irq 17 at device 0.0 on pci5
re0: Using 1 MSI-X message
re0: Chip rev. 0x2c800000
re0: MAC rev. 0x00100000
miibus0: <MII bus> on re0
rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus0
rgephy0: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow
re0: Using defaults for TSO: 65518/35/2048
re0: Ethernet address: bc:5f:f4:37:43:ef
re0: netmap queues/slots: TX 1/256, RX 1/256
ehci1: <Intel Panther Point USB 2.0 controller> mem 0xf7f17000-0xf7f173ff irq 23 at device 29.0 on pci0
usbus2: EHCI version 1.0
usbus2 on ehci1
pcib6: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci6: <ACPI PCI bus> on pcib6
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
ahci1: <Intel Panther Point AHCI SATA controller> port 0xf070-0xf077,0xf060-0xf063,0xf050-0xf057,0xf040-0xf043,0xf020-0xf03f mem 0xf7f16000-0xf7f167ff irq 19 at device 31.2 on pci0
ahci1: AHCI v1.30 with 6 6Gbps ports, Port Multiplier not supported
ahcich2: <AHCI channel> at channel 0 on ahci1
ahcich3: <AHCI channel> at channel 1 on ahci1
ahcich4: <AHCI channel> at channel 2 on ahci1
ahcich5: <AHCI channel> at channel 3 on ahci1
ahcich6: <AHCI channel> at channel 4 on ahci1
ahcich7: <AHCI channel> at channel 5 on ahci1
ahciem0: <AHCI enclosure management bridge> on ahci1
acpi_button0: <Power Button> on acpi0
ppc1: <Parallel port> port 0x378-0x37f,0x778-0x77f irq 5 drq 3 on acpi0
ppc1: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc1: FIFO with 16/16/9 bytes threshold
ppbus0: <Parallel port bus> on ppc1
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xcffff,0xd0000-0xd4fff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
ppc0: cannot reserve I/O port range
est0: <Enhanced SpeedStep Frequency Control> on cpu0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
est2: <Enhanced SpeedStep Frequency Control> on cpu2
est3: <Enhanced SpeedStep Frequency Control> on cpu3
(noperiph:siisch0:0:-1:ffffffff): rescan already queued
(noperiph:siisch1:0:-1:ffffffff): rescan already queued
usbus0: 5.0Gbps Super Speed USB v3.0
Timecounters tick every 1.000 msec
hdacc0: <Realtek ALC662 HDA CODEC> at cad 0 on hdac0
hdaa0: <Realtek ALC662 Audio Function Group> at nid 1 on hdacc0
pcm0: <Realtek ALC662 (Rear Analog)> at nid 20 and 24,26 on hdaa0
pcm1: <Realtek ALC662 (Front Analog)> at nid 27 and 25 on hdaa0
usbus1: 480Mbps High Speed USB v2.0
usbus2: 480Mbps High Speed USB v2.0
ugen0.1: <0x8086> at usbus0
uhub0: <0x8086 XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
ugen2.1: <Intel> at usbus2
uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
ugen1.1: <Intel> at usbus1
uhub2: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
ses0 at ahciem0 bus 0 scbus12 target 0 lun 0
ses0: <AHCI SGPIO Enclosure 1.00 0001> SEMB S-E-S 2.00 device
ses0: SEMB SES Device
ada0 at siisch0 bus 0 scbus0 target 0 lun 0
ada0: <OCZ-REVODRIVE 1.37> ATA8-ACS SATA 2.x device
ada0: Serial Number OCZ-4I0B17Q0H2K7990M
ada0: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada0: Command Queueing enabled
ada0: 57241MB (117231408 512 byte sectors)
ada1 at siisch1 bus 0 scbus1 target 0 lun 0
ada1: <OCZ-REVODRIVE 1.37> ATA8-ACS SATA 2.x device
ada1: Serial Number OCZ-513Y931NLS8L79KY
ada1: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada1: Command Queueing enabled
ada1: 57241MB (117231408 512 byte sectors)
SMP: AP CPU #1 Launched!
SMP: AP CPU #3 Launched!
SMP: AP CPU #2 Launched!
GEOM_RAID: SiI-160406213114: Array SiI-160406213114 created.
Timecounter "TSC-low" frequency 1646297310 Hz quality 1000
WARNING: WITNESS option enabled, expect reduced performance.
GEOM_RAID: SiI-160406213114: Disk ada0 state changed from NONE to ACTIVE.
GEOM_RAID: SiI-160406213114: Subdisk SiI Raid0 Set:0-ada0 state changed from NONE to STALE.
GEOM_RAID: SiI-160406213114: Disk ada1 state changed from NONE to ACTIVE.
Trying to mount root from ufs:/dev/ufs/FreeBSD_Install [ro,noatime]...
GEOM_RAID: SiI-160406213114: Subdisk SiI Raid0 Set:1-ada1 state changed from NONE to STALE.
GEOM_RAID: SiI-160406213114: Array started.
GEOM_RAID: SiI-160406213114: Subdisk SiI Raid0 Set:0-ada0 state changed from STALE to ACTIVE.
GEOM_RAID: SiI-160406213114: Subdisk SiI Raid0 Set:1-ada1 state changed from STALE to ACTIVE.
GEOM_RAID: SiI-160406213114: Volume SiI Raid0 Set state changed from STARTING to OPTIMAL.
Root mount waiting for: GRAID usbus2 usbus1 usbus0
GEOM_RAID: SiI-160406213114: Provider raid/r0 for volume SiI Raid0 Set created.
uhub0: 8 ports with 8 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
Root mount waiting for: usbus2 usbus1 usbus0
ugen0.2: <vendor 0x0409> at usbus0
uhub3: <vendor 0x0409 product 0x005a, class 9/0, rev 2.00/1.00, addr 1> on usbus0
ugen2.2: <vendor 0x8087> at usbus2
uhub4: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on usbus2
ugen1.2: <vendor 0x8087> at usbus1
uhub5: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on usbus1
uhub3: 4 ports with 4 removable, self powered
Root mount waiting for: usbus2 usbus1 usbus0
ugen0.3: <vendor 0x0402> at usbus0
uhub4: 6 ports with 6 removable, self powered
uhub5: 6 ports with 6 removable, self powered
Root mount waiting for: usbus2 usbus1 usbus0
ugen0.4: <vendor 0x04d9> at usbus0
ukbd0: <vendor 0x04d9 USB Keyboard, class 0/0, rev 1.10/3.10, addr 3> on usbus0
kbd2 at ukbd0
ugen2.3: <vendor 0x093a> at usbus2
Root mount waiting for: usbus1
ugen1.3: <Kingston> at usbus1
umass0: <Kingston DataTravelerMini, class 0/0, rev 2.00/1.00, addr 3> on usbus1
umass0: SCSI over Bulk-Only; quirks = 0xc100
umass0:13:0: Attached to scbus13
da0 at umass-sim0 bus 0 scbus13 target 0 lun 0
da0: <Kingston DataTravelerMini PMAP> Removable Direct Access SCSI device
da0: Serial Number 5B7410730044
da0: 40.000MB/s transfers
da0: 1968MB (4030464 512 byte sectors)
da0: quirks=0x2<NO_6_BYTE>
GEOM: da0: the secondary GPT header is not in the last LBA.
GEOM: diskid/DISK-5B7410730044: the secondary GPT header is not in the last LBA.
mountroot: waiting for device /dev/ufs/FreeBSD_Install...
GEOM: diskid/DISK-5B7410730044: the secondary GPT header is not in the last LBA.
random: unblocking device.
re0: link state changed to UP
ums0: <vendor 0x093a USB OPTICAL MOUSE, class 0/0, rev 1.10/1.00, addr 3> on usbus2
ums0: 5 buttons and [XYZT] coordinates ID=0
uhid0: <vendor 0x04d9 USB Keyboard, class 0/0, rev 1.10/3.10, addr 3> on usbus0
re0: link state changed to DOWN
re0: link state changed to UP
[-- Attachment #5 --]
Copyright (c) 1992-2016 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 11.0-CURRENT #0 r297561: Mon Apr 4 22:42:00 MSK 2016
timp@fbsd11:/usr/obj/usr/src/sys/GENERIC amd64
FreeBSD clang version 3.8.0 (tags/RELEASE_380/final 262564) (based on LLVM 3.8.0)
WARNING: WITNESS option enabled, expect reduced performance.
VT(vga): resolution 640x480
CPU: Intel(R) Core(TM) i3-2120 CPU @ 3.30GHz (3292.59-MHz K8-class CPU)
Origin="GenuineIntel" Id=0x206a7 Family=0x6 Model=0x2a Stepping=7
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x1d9ae3bf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,POPCNT,TSCDLT,XSAVE,OSXSAVE,AVX>
AMD Features=0x28100800<SYSCALL,NX,RDTSCP,LM>
AMD Features2=0x1<LAHF>
XSAVE Features=0x1<XSAVEOPT>
VT-x: PAT,HLT,MTF,PAUSE,EPT,UG,VPID
TSC: P-state invariant, performance statistics
real memory = 8589934592 (8192 MB)
avail memory = 8207171584 (7826 MB)
Event timer "LAPIC" quality 600
ACPI APIC Table: <ALASKA A M I>
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
FreeBSD/SMP: 1 package(s) x 2 core(s) x 2 hardware threads
ioapic0 <Version 2.0> irqs 0-23 on motherboard
random: entropy device external interface
kbd1 at kbdmux0
netmap: loaded module
module_register_init: MOD_LOAD (vesa, 0xffffffff80f05eb0, 0) error 19
vtvga0: <VT VGA driver> on motherboard
cryptosoft0: <software crypto> on motherboard
acpi0: <ALASKA A M I> on motherboard
acpi0: Power Button (fixed)
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
cpu2: <ACPI CPU> on acpi0
cpu3: <ACPI CPU> on acpi0
hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 950
Event timer "HPET" frequency 14318180 Hz quality 550
Event timer "HPET1" frequency 14318180 Hz quality 440
Event timer "HPET2" frequency 14318180 Hz quality 440
Event timer "HPET3" frequency 14318180 Hz quality 440
Event timer "HPET4" frequency 14318180 Hz quality 440
atrtc0: <AT realtime clock> port 0x70-0x77 irq 8 on acpi0
atrtc0: Warning: Couldn't map I/O.
Event timer "RTC" frequency 32768 Hz quality 0
attimer0: <AT timer> port 0x40-0x43,0x50-0x53 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0xe000-0xe0ff mem 0xe0000000-0xefffffff,0xf7e00000-0xf7e3ffff irq 16 at device 0.0 on pci1
vgapci0: Boot video device
hdac0: <ATI (0xaab0) HDA Controller> mem 0xf7e60000-0xf7e63fff irq 17 at device 0.1 on pci1
hdac0: hdac_get_capabilities: Invalid corb size (0)
device_attach: hdac0 attach returned 6
xhci0: <Intel Panther Point USB 3.0 controller> mem 0xf7f00000-0xf7f0ffff irq 16 at device 20.0 on pci0
xhci0: 32 bytes context size, 64-bit DMA
xhci0: Port routing mask set to 0xffffffff
usbus0 on xhci0
pci0: <simple comms> at device 22.0 (no driver attached)
ehci0: <Intel Panther Point USB 2.0 controller> mem 0xf7f18000-0xf7f183ff irq 16 at device 26.0 on pci0
usbus1: EHCI version 1.0
usbus1 on ehci0
hdac0: <Intel Panther Point HDA Controller> mem 0xf7f10000-0xf7f13fff irq 22 at device 27.0 on pci0
pcib2: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pci2: <ACPI PCI bus> on pcib2
pcib3: <PCI-PCI bridge> irq 16 at device 0.0 on pci2
pci3: <PCI bus> on pcib3
siis0: <SiI3124 SATA controller> port 0xd000-0xd00f mem 0xf7d88000-0xf7d8807f,0xf7d80000-0xf7d87fff irq 16 at device 0.0 on pci3
siisch0: <SIIS channel> at channel 0 on siis0
siisch1: <SIIS channel> at channel 1 on siis0
siisch2: <SIIS channel> at channel 2 on siis0
siisch3: <SIIS channel> at channel 3 on siis0
pcib4: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0
pci4: <ACPI PCI bus> on pcib4
ahci0: <ASMedia ASM1061 AHCI SATA controller> port 0xc050-0xc057,0xc040-0xc043,0xc030-0xc037,0xc020-0xc023,0xc000-0xc01f mem 0xf7c00000-0xf7c001ff irq 16 at device 0.0 on pci4
ahci0: AHCI v1.20 with 2 6Gbps ports, Port Multiplier supported
ahcich0: <AHCI channel> at channel 0 on ahci0
ahcich1: <AHCI channel> at channel 1 on ahci0
pcib5: <ACPI PCI-PCI bridge> irq 17 at device 28.5 on pci0
pci5: <ACPI PCI bus> on pcib5
re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F/G PCIe Gigabit Ethernet> port 0xb000-0xb0ff mem 0xf0004000-0xf0004fff,0xf0000000-0xf0003fff irq 17 at device 0.0 on pci5
re0: Using 1 MSI-X message
re0: Chip rev. 0x2c800000
re0: MAC rev. 0x00100000
miibus0: <MII bus> on re0
rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on miibus0
rgephy0: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow
re0: Using defaults for TSO: 65518/35/2048
re0: Ethernet address: bc:5f:f4:37:43:ef
re0: netmap queues/slots: TX 1/256, RX 1/256
ehci1: <Intel Panther Point USB 2.0 controller> mem 0xf7f17000-0xf7f173ff irq 23 at device 29.0 on pci0
usbus2: EHCI version 1.0
usbus2 on ehci1
pcib6: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci6: <ACPI PCI bus> on pcib6
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
ahci1: <Intel Panther Point AHCI SATA controller> port 0xf070-0xf077,0xf060-0xf063,0xf050-0xf057,0xf040-0xf043,0xf020-0xf03f mem 0xf7f16000-0xf7f167ff irq 19 at device 31.2 on pci0
ahci1: AHCI v1.30 with 6 6Gbps ports, Port Multiplier not supported
ahcich2: <AHCI channel> at channel 0 on ahci1
ahcich3: <AHCI channel> at channel 1 on ahci1
ahcich4: <AHCI channel> at channel 2 on ahci1
ahcich5: <AHCI channel> at channel 3 on ahci1
ahcich6: <AHCI channel> at channel 4 on ahci1
ahcich7: <AHCI channel> at channel 5 on ahci1
ahciem0: <AHCI enclosure management bridge> on ahci1
acpi_button0: <Power Button> on acpi0
ppc1: <Parallel port> port 0x378-0x37f,0x778-0x77f irq 5 drq 3 on acpi0
ppc1: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc1: FIFO with 16/16/9 bytes threshold
ppbus0: <Parallel port bus> on ppc1
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xcffff,0xd0000-0xd4fff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
ppc0: cannot reserve I/O port range
est0: <Enhanced SpeedStep Frequency Control> on cpu0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
est2: <Enhanced SpeedStep Frequency Control> on cpu2
est3: <Enhanced SpeedStep Frequency Control> on cpu3
(noperiph:siisch0:0:-1:ffffffff): rescan already queued
(noperiph:siisch1:0:-1:ffffffff): rescan already queued
usbus0: 5.0Gbps Super Speed USB v3.0
Timecounters tick every 1.000 msec
hdacc0: <Realtek ALC662 HDA CODEC> at cad 0 on hdac0
hdaa0: <Realtek ALC662 Audio Function Group> at nid 1 on hdacc0
pcm0: <Realtek ALC662 (Rear Analog)> at nid 20 and 24,26 on hdaa0
pcm1: <Realtek ALC662 (Front Analog)> at nid 27 and 25 on hdaa0
usbus1: 480Mbps High Speed USB v2.0
usbus2: 480Mbps High Speed USB v2.0
ugen0.1: <0x8086> at usbus0
uhub0: <0x8086 XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
ugen2.1: <Intel> at usbus2
uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
ugen1.1: <Intel> at usbus1
uhub2: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
ses0 at ahciem0 bus 0 scbus12 target 0 lun 0
ses0: <AHCI SGPIO Enclosure 1.00 0001> SEMB S-E-S 2.00 device
ses0: SEMB SES Device
ada0 at siisch0 bus 0 scbus0 target 0 lun 0
ada0: <OCZ-REVODRIVE 1.37> ATA8-ACS SATA 2.x device
ada0: Serial Number OCZ-4I0B17Q0H2K7990M
ada0: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada0: Command Queueing enabled
ada0: 57241MB (117231408 512 byte sectors)
ada1 at siisch1 bus 0 scbus1 target 0 lun 0
ada1: <OCZ-REVODRIVE 1.37> ATA8-ACS SATA 2.x device
ada1: Serial Number OCZ-513Y931NLS8L79KY
ada1: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada1: Command Queueing enabled
ada1: 57241MB (117231408 512 byte sectors)
SMP: AP CPU #1 Launched!
SMP: AP CPU #3 Launched!
SMP: AP CPU #2 Launched!
GEOM_RAID: SiI-160406212450: Array SiI-160406212450 created.
Timecounter "TSC-low" frequency 1646296054 Hz quality 1000
WARNING: WITNESS option enabled, expect reduced performance.
GEOM_RAID: SiI-160406212450: Disk ada0 state changed from NONE to ACTIVE.
Trying to mount root from ufs:/dev/ufs/FreeBSD_Install [ro,noatime]...
GEOM_RAID: SiI-160406212450: Subdisk SiI Raid1 Set:0-ada0 state changed from NONE to ACTIVE.
GEOM_RAID: SiI-160406212450: Disk ada1 state changed from NONE to ACTIVE.
GEOM_RAID: SiI-160406212450: Subdisk SiI Raid1 Set:1-ada1 state changed from NONE to ACTIVE.
GEOM_RAID: SiI-160406212450: Array started.
GEOM_RAID: SiI-160406212450: Volume SiI Raid1 Set state changed from STARTING to OPTIMAL.
Root mount waiting for: GRAID usbus2 usbus1 usbus0
GEOM_RAID: SiI-160406212450: Provider raid/r0 for volume SiI Raid1 Set created.
GEOM: raid/r0: corrupt or invalid GPT detected.
GEOM: raid/r0: GPT rejected -- may not be recoverable.
uhub0: 8 ports with 8 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
Root mount waiting for: usbus2 usbus1 usbus0
ugen0.2: <vendor 0x0409> at usbus0
uhub3: <vendor 0x0409 product 0x005a, class 9/0, rev 2.00/1.00, addr 1> on usbus0
ugen2.2: <vendor 0x8087> at usbus2
uhub4: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on usbus2
uhub3: 4 ports with 4 removable, self powered
ugen1.2: <vendor 0x8087> at usbus1
uhub5: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on usbus1
Root mount waiting for: usbus2 usbus1 usbus0
ugen0.3: <vendor 0x0402> at usbus0
uhub4: 6 ports with 6 removable, self powered
uhub5: 6 ports with 6 removable, self powered
Root mount waiting for: usbus2 usbus1 usbus0
ugen0.4: <vendor 0x04d9> at usbus0
ukbd0: <vendor 0x04d9 USB Keyboard, class 0/0, rev 1.10/3.10, addr 3> on usbus0
kbd2 at ukbd0
ugen2.3: <vendor 0x093a> at usbus2
Root mount waiting for: usbus1
ugen1.3: <Kingston> at usbus1
umass0: <Kingston DataTravelerMini, class 0/0, rev 2.00/1.00, addr 3> on usbus1
umass0: SCSI over Bulk-Only; quirks = 0xc100
umass0:13:0: Attached to scbus13
da0 at umass-sim0 bus 0 scbus13 target 0 lun 0
da0: <Kingston DataTravelerMini PMAP> Removable Direct Access SCSI device
da0: Serial Number 5B7410730044
da0: 40.000MB/s transfers
da0: 1968MB (4030464 512 byte sectors)
da0: quirks=0x2<NO_6_BYTE>
GEOM: da0: the secondary GPT header is not in the last LBA.
GEOM: diskid/DISK-5B7410730044: the secondary GPT header is not in the last LBA.
mountroot: waiting for device /dev/ufs/FreeBSD_Install...
GEOM: diskid/DISK-5B7410730044: the secondary GPT header is not in the last LBA.
random: unblocking device.
re0: link state changed to UP
ums0: <vendor 0x093a USB OPTICAL MOUSE, class 0/0, rev 1.10/1.00, addr 3> on usbus2
ums0: 5 buttons and [XYZT] coordinates ID=0
uhid0: <vendor 0x04d9 USB Keyboard, class 0/0, rev 1.10/3.10, addr 3> on usbus0
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?CAAoTqftw--ks3BDZ0iCfQ25fb%2BYGrr9VknjVSbUQ1kFSLGdX-A>