Skip site navigation (1)Skip section navigation (2)
Date:      Fri, 30 Jul 2010 14:02:37 +0100
From:      Anton Shterenlikht <mexas@bristol.ac.uk>
To:        Andriy Gapon <avg@icyb.net.ua>
Cc:        lstewart@freebsd.org, Gavin Atkinson <gavin@freebsd.org>, Anton Shterenlikht <mexas@bristol.ac.uk>, freebsd-current@freebsd.org
Subject:   Re: amd64 panic snd_hda - hdac_get_capabilities: Invalid corb size (0)
Message-ID:  <20100730130237.GA9853@mech-cluster241.men.bris.ac.uk>
In-Reply-To: <4C52C00E.3050400@icyb.net.ua>
References:  <20100728160152.GA91835@mech-cluster241.men.bris.ac.uk> <4C5055C6.5050208@icyb.net.ua> <20100728161715.GA91906@mech-cluster241.men.bris.ac.uk> <4C505BE8.1050308@icyb.net.ua> <20100728164449.GA92092@mech-cluster241.men.bris.ac.uk> <4C505FFC.6000601@icyb.net.ua> <20100728171324.GB92206@mech-cluster241.men.bris.ac.uk> <4C50663B.7030203@icyb.net.ua> <20100730115753.GA9578@mech-cluster241.men.bris.ac.uk> <4C52C00E.3050400@icyb.net.ua>

next in thread | previous in thread | raw e-mail | index | archive | help
On Fri, Jul 30, 2010 at 03:05:34PM +0300, Andriy Gapon wrote:
> on 30/07/2010 14:57 Anton Shterenlikht said the following:
> > On Wed, Jul 28, 2010 at 08:17:47PM +0300, Andriy Gapon wrote:
> >> Change it to if (1) { ...}.
> > 
> > did that, and did a cold reboot:
> > 
> > % dmesg | fgrep -i hda
> > hdac0: <ATI SB600 High Definition Audio Controller> irq 16 at device 20.2 on pci0
> > hdac0: HDA Driver Revision: 20100226_0142
> > hdac0: [ITHREAD]
> > hdac0: hdac_get_capabilities: Invalid corb size (0)
> > hdac0: Resetting corb size to 256
> > hdac0: hdac_get_capabilities: Invalid rirb size (0)
> > hdac0: Resetting rirb size to 256
> > %
> > 
> > I don't think the device attached.
> 
> No further interesting/related messages after those above?
> Could you please try a verbose boot?

from a verbose boot:

% dmesg | fgrep -i hda
hdac0: <ATI SB600 High Definition Audio Controller> irq 16 at device 20.2 on pci0
hdac0: HDA Driver Revision: 20100226_0142
hdac0: Lazy allocation of 0x4000 bytes rid 0x10 type 3 at 0xb7fb0000
hdac0: [MPSAFE]
hdac0: [ITHREAD]
hdac0: hdac_get_capabilities: Invalid corb size (0)
hdac0: Resetting corb size to 256
hdac0: hdac_get_capabilities: Invalid rirb size (0)
hdac0: Resetting rirb size to 256
hdac0: Caps: OSS 0, ISS 0, BSS 0, NSDO 1, CORB 256, RIRB 256
hdac0: 
%

here's the full /var/run/dmesg.boot from "boot -v":


Copyright (c) 1992-2010 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 9.0-CURRENT #0 r210638M: Fri Jul 30 12:16:29 BST 2010
    root@mech-aslap239.men.bris.ac.uk:/usr/obj/usr/src/sys/BUZI amd64
WARNING: WITNESS option enabled, expect reduced performance.
Table 'FACP' at 0xb7fc8084
Table 'SLIC' at 0xb7fc8220
Table 'EPTH' at 0xb7fc8398
Table 'APIC' at 0xb7fc83d0
Table 'MCFG' at 0xb7fc8434
Table 'TCPA' at 0xb7fc8470
Table 'SSDT' at 0xb7fd98db
Table 'SSDT' at 0xb7fd9934
ACPI: No SRAT table found
Preloaded elf kernel "/boot/kernel/kernel" at 0xffffffff810a8000.
Preloaded elf obj module "/boot/kernel/zfs.ko" at 0xffffffff810a8208.
Preloaded elf obj module "/boot/kernel/opensolaris.ko" at 0xffffffff810a88b0.
Preloaded elf obj module "/boot/kernel/krpc.ko" at 0xffffffff810a8ee0.
Preloaded /boot/zfs/zpool.cache "/boot/zfs/zpool.cache" at 0xffffffff810a9508.
Calibrating TSC clock ... TSC clock: 1994947870 Hz
CPU: AMD Turion(tm) 64 X2 Mobile Technology TL-60 (1994.95-MHz K8-class CPU)
  Origin = "AuthenticAMD"  Id = 0x60f82  Family = f  Model = 68  Stepping = 2
  Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
  Features2=0x2001<SSE3,CX16>
  AMD Features=0xea500800<SYSCALL,NX,MMX+,FFXSR,RDTSCP,LM,3DNow!+,3DNow!>
  AMD Features2=0x11f<LAHF,CMP,SVM,ExtAPIC,CR8,Prefetch>
L1 2MB data TLB: 8 entries, fully associative
L1 2MB instruction TLB: 8 entries, fully associative
L1 4KB data TLB: 32 entries, fully associative
L1 4KB instruction TLB: 32 entries, fully associative
L1 data cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L1 instruction cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L2 2MB unified TLB: 0 entries, disabled/not present
L2 4KB data TLB: 512 entries, 4-way associative
L2 4KB instruction TLB: 512 entries, 4-way associative
L2 unified cache: 512 kbytes, 64 bytes/line, 1 lines/tag, 16-way associative
real memory  = 3221225472 (3072 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009bfff, 634880 bytes (155 pages)
0x00000000010d7000 - 0x00000000b2903fff, 2978140160 bytes (727085 pages)
avail memory = 2960908288 (2823 MB)
Event timer "LAPIC" frequency 0 Hz quality 500
ACPI APIC Table: <HP     0944    >
INTR: Adding local APIC 1 as a target
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
FreeBSD/SMP: 1 package(s) x 2 core(s)
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
x86bios:   IVT 0x000000-0x0004ff at 0xffffff0000000000
x86bios:  SSEG 0x010000-0x01ffff at 0xffffff8000010000
x86bios:  EBDA 0x09f000-0x09ffff at 0xffffff000009f000
x86bios:   ROM 0x0a0000-0x0effff at 0xffffff00000a0000
APIC: CPU 0 has ACPI ID 1
APIC: CPU 1 has ACPI ID 2
ULE: setup cpu 0
ULE: setup cpu 1
ACPI: RSDP 0xfe0b0 00024 (v02 HP    )
ACPI: XSDT 0xb7fc81bc 00064 (v01 HPQOEM SLIC-MPC 00000001 HP   00000001)
ACPI: FACP 0xb7fc8084 000F4 (v04 HP     0944     00000003 HP   00000001)
ACPI Error: 32/64X address mismatch in Pm2ControlBlock: 0x00008800/0x0000000000008100, using 32 (20100702/tbfadt-526)
ACPI: DSDT 0xb7fc84a4 11437 (v01 HP        SB400 00010000 MSFT 03000001)
ACPI: FACS 0xb7fe7d80 00040
ACPI: SLIC 0xb7fc8220 00176 (v01 HPQOEM SLIC-MPC 00000001 HP   00000001)
ACPI: EPTH 0xb7fc8398 00038 (v01 HP     0944     00000001 HP   00000001)
ACPI: APIC 0xb7fc83d0 00062 (v01 HP     0944     00000001 HP   00000001)
ACPI: MCFG 0xb7fc8434 0003C (v01 HP     0944     00000001 HP   00000001)
ACPI: TCPA 0xb7fc8470 00032 (v02 HP     0944     00000001 HP   00000001)
ACPI: SSDT 0xb7fd98db 00059 (v01 HP       HPQNLP 00000001 MSFT 03000001)
ACPI: SSDT 0xb7fd9934 00206 (v01 HP     PSSTBLID 00000001 HP   00000001)
MADT: Found IO APIC ID 2, Interrupt 0 at 0xfec00000
ioapic0: Changing APIC ID to 2
ioapic0: Routing external 8259A's -> intpin 0
MADT: Interrupt override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
MADT: Interrupt override: source 9, irq 9
ioapic0: intpin 9 trigger: level
ioapic0: intpin 9 polarity: low
lapic0: Routing NMI -> LINT1
lapic0: LINT1 trigger: edge
lapic0: LINT1 polarity: high
ioapic0 <Version 2.1> irqs 0-23 on motherboard
cpu0 BSP:
     ID: 0x00000000   VER: 0x80050010 LDR: 0x00000000 DFR: 0xffffffff
  lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
  timer: 0x000100ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
   cmci: 0x00000000
firmware: 'iwn6050fw' version 0: 463692 bytes loaded at 0xffffffff80a42184
firmware: 'iwn1000fw' version 0: 335056 bytes loaded at 0xffffffff808aa884
firmware: 'iwn4965fw' version 0: 187972 bytes loaded at 0xffffffff808fc634
firmware: 'iwn5000fw' version 0: 353240 bytes loaded at 0xffffffff8092a554
firmware: 'iwn5150fw' version 0: 337400 bytes loaded at 0xffffffff80980a04
wlan: <802.11 Link Layer>
firmware: 'rt2561fw' version 0: 8192 bytes loaded at 0xffffffff80abe8e4
firmware: 'rt2561sfw' version 0: 8192 bytes loaded at 0xffffffff80ac09c4
firmware: 'rt2661fw' version 0: 8192 bytes loaded at 0xffffffff80ac2aa4
snd_unit_init() u=0x00ff8000 [512] d=0x00007c00 [32] c=0x000003ff [1024]
feeder_register: snd_unit=-1 snd_maxautovchans=16 latency=5 feeder_rate_min=1 feeder_rate_max=2016000 feeder_rate_round=25
firmware: 'rt2860fw' version 0: 8192 bytes loaded at 0xffffffff80ac4b84
firmware: 'iwn6000fw' version 0: 454608 bytes loaded at 0xffffffff809d30d4
kbd: new array size 4
kbd1 at kbdmux0
mem: <memory>
io: <I/O>
null: <null device, zero device>
random: <entropy source, Software, Yarrow>
CPU0: local APIC error 0x80
acpi0: <HPQOEM SLIC-MPC> on motherboard
PCIe: Memory Mapped configuration base @ 0xe0000000
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.C08B.C08C.C08D.C154 -> bus 1 dev 5 func 0
ioapic0: routing intpin 9 (ISA IRQ 9) to lapic 0 vector 48
acpi0: [MPSAFE]
acpi0: [ITHREAD]
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.C08B.C093 -> bus 0 dev 0 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.C08B.C090 -> bus 0 dev 0 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.C08B.C09F.C0B2 -> bus 0 dev 20 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.C08B.C275.C278 -> bus 0 dev 18 func 0
acpi0: Power Button (fixed)
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.C08B.C096 -> bus 0 dev 0 func 0
unknown: I/O range not supported
acpi0: reservation of 0, 8000000 (3) failed
acpi0: reservation of 100000, fff00000 (3) failed
ACPI timer: 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 -> 10
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x8008-0x800b on acpi0
cpu0: <ACPI CPU> on acpi0
cpu0: switching to generic Cx mode
cpu1: <ACPI CPU> on acpi0
acpi_ec0: <Embedded Controller: GPE 0x11> port 0x62,0x66 on acpi0
pci_link0:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0  255   N     0  10 11
  Validation          0  255   N     0  10 11
  After Disable       0  255   N     0  10 11
pci_link1:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0  255   N     0  10 11
  Validation          0  255   N     0  10 11
  After Disable       0  255   N     0  10 11
pci_link2:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0  255   N     0  10 11
  Validation          0  255   N     0  10 11
  After Disable       0  255   N     0  10 11
pci_link3:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0  255   N     0  10 11
  Validation          0  255   N     0  10 11
  After Disable       0  255   N     0  10 11
pci_link4:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0  255   N     0  10 11
  Validation          0  255   N     0  10 11
  After Disable       0  255   N     0  10 11
pci_link5:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0  255   N     0  9
  Validation          0  255   N     0  9
  After Disable       0  255   N     0  9
pci_link6:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0  255   N     0  10 11
  Validation          0  255   N     0  10 11
  After Disable       0  255   N     0  10 11
pci_link7:        Index  IRQ  Rtd  Ref  IRQs
  Initial Probe       0  255   N     0  10 11
  Validation          0  255   N     0  10 11
  After Disable       0  255   N     0  10 11
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: domain=0, physical bus=0
found->	vendor=0x1002, dev=0x7910, revid=0x00
	domain=0, bus=0, slot=0, func=0
	class=06-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0006, statreg=0x2220, cachelnsz=0 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1002, dev=0x7912, revid=0x00
	domain=0, bus=0, slot=1, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0007, statreg=0x0230, cachelnsz=0 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x0c (3000 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1002, dev=0x7914, revid=0x00
	domain=0, bus=0, slot=4, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message
found->	vendor=0x1002, dev=0x7915, revid=0x00
	domain=0, bus=0, slot=5, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
	cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message
found->	vendor=0x1002, dev=0x4380, revid=0x00
	domain=0, bus=0, slot=18, func=0
	class=01-01-8f, hdrtype=0x00, mfdev=0
	cmdreg=0x0007, statreg=0x0230, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=10
	powerspec 2  supports D0 D3  current D0
	map[10]: type I/O Port, range 32, base 0x9000, size  3, enabled
	map[14]: type I/O Port, range 32, base 0x9008, size  2, enabled
	map[18]: type I/O Port, range 32, base 0x9010, size  3, enabled
	map[1c]: type I/O Port, range 32, base 0x5018, size  2, enabled
	map[20]: type I/O Port, range 32, base 0x5020, size  4, enabled
	map[24]: type Memory, range 32, base 0xcc409000, size 10, enabled
pcib0: matched entry for 0.18.INTA
pcib0: slot 18 INTA hardwired to IRQ 16
found->	vendor=0x1002, dev=0x4387, revid=0x00
	domain=0, bus=0, slot=19, func=0
	class=0c-03-10, hdrtype=0x00, mfdev=1
	cmdreg=0x0007, statreg=0x02a0, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=11
	map[10]: type Memory, range 32, base 0xcc401000, size 12, enabled
pcib0: matched entry for 0.19.INTA
pcib0: slot 19 INTA hardwired to IRQ 23
found->	vendor=0x1002, dev=0x4388, revid=0x00
	domain=0, bus=0, slot=19, func=1
	class=0c-03-10, hdrtype=0x00, mfdev=0
	cmdreg=0x0007, statreg=0x02a0, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=5
	map[10]: type Memory, range 32, base 0xcc402000, size 12, enabled
pcib0: matched entry for 0.19.INTB
pcib0: slot 19 INTB hardwired to IRQ 17
found->	vendor=0x1002, dev=0x4389, revid=0x00
	domain=0, bus=0, slot=19, func=2
	class=0c-03-10, hdrtype=0x00, mfdev=0
	cmdreg=0x0007, statreg=0x02a0, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=c, irq=5
	map[10]: type Memory, range 32, base 0xcc403000, size 12, enabled
pcib0: matched entry for 0.19.INTC
pcib0: slot 19 INTC hardwired to IRQ 17
found->	vendor=0x1002, dev=0x438a, revid=0x00
	domain=0, bus=0, slot=19, func=3
	class=0c-03-10, hdrtype=0x00, mfdev=0
	cmdreg=0x0007, statreg=0x02a0, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=5
	map[10]: type Memory, range 32, base 0xcc404000, size 12, enabled
pcib0: matched entry for 0.19.INTB
pcib0: slot 19 INTB hardwired to IRQ 17
found->	vendor=0x1002, dev=0x438b, revid=0x00
	domain=0, bus=0, slot=19, func=4
	class=0c-03-10, hdrtype=0x00, mfdev=0
	cmdreg=0x0007, statreg=0x02a0, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=c, irq=5
	map[10]: type Memory, range 32, base 0xcc405000, size 12, enabled
pcib0: matched entry for 0.19.INTC
pcib0: slot 19 INTC hardwired to IRQ 17
found->	vendor=0x1002, dev=0x4386, revid=0x00
	domain=0, bus=0, slot=19, func=5
	class=0c-03-20, hdrtype=0x00, mfdev=0
	cmdreg=0x0007, statreg=0x02b0, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=d, irq=11
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type Memory, range 32, base 0xcc406000, size  8, enabled
pcib0: matched entry for 0.19.INTD
pcib0: slot 19 INTD hardwired to IRQ 23
found->	vendor=0x1002, dev=0x4385, revid=0x14
	domain=0, bus=0, slot=20, func=0
	class=0c-05-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0003, statreg=0x0230, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	map[10]: type I/O Port, range 32, base 0x8200, size  4, enabled
found->	vendor=0x1002, dev=0x438c, revid=0x00
	domain=0, bus=0, slot=20, func=1
	class=01-01-82, hdrtype=0x00, mfdev=0
	cmdreg=0x0005, statreg=0x0220, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=10
	map[20]: type I/O Port, range 32, base 0x5040, size  4, enabled
pcib0: matched entry for 0.20.INTA
pcib0: slot 20 INTA hardwired to IRQ 16
found->	vendor=0x1002, dev=0x4383, revid=0x00
	domain=0, bus=0, slot=20, func=2
	class=04-03-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0006, statreg=0x0410, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=10
	powerspec 2  supports D0 D3  current D0
	map[10]: type Memory, range 64, base 0xcc408000, size 14, enabled
pcib0: matched entry for 0.20.INTA
pcib0: slot 20 INTA hardwired to IRQ 16
found->	vendor=0x1002, dev=0x438d, revid=0x00
	domain=0, bus=0, slot=20, func=3
	class=06-01-00, hdrtype=0x00, mfdev=1
	cmdreg=0x000f, statreg=0x0220, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1002, dev=0x4384, revid=0x00
	domain=0, bus=0, slot=20, func=4
	class=06-04-01, hdrtype=0x01, mfdev=1
	cmdreg=0x0027, statreg=0x02a0, cachelnsz=0 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x1100, revid=0x00
	domain=0, bus=0, slot=24, func=0
	class=06-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x1101, revid=0x00
	domain=0, bus=0, slot=24, func=1
	class=06-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x1102, revid=0x00
	domain=0, bus=0, slot=24, func=2
	class=06-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found->	vendor=0x1022, dev=0x1103, revid=0x00
	domain=0, bus=0, slot=24, func=3
	class=06-00-00, hdrtype=0x00, mfdev=1
	cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pcib1:   domain            0
pcib1:   secondary bus     1
pcib1:   subordinate bus   1
pcib1:   I/O decode        0x4000-0x4fff
pcib1:   memory decode     0xcc200000-0xcc3fffff
pcib1:   prefetched decode 0xc0000000-0xc7ffffff
pci1: <ACPI PCI bus> on pcib1
pci1: domain=0, physical bus=1
found->	vendor=0x1002, dev=0x791f, revid=0x00
	domain=0, bus=1, slot=5, func=0
	class=03-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=b, irq=11
	powerspec 2  supports D0 D1 D2 D3  current D0
	MSI supports 1 message, 64 bit
	map[10]: type Prefetchable Memory, range 64, base 0xc0000000, size 27, enabled
pcib1: requested memory range 0xc0000000-0xc7ffffff: good
	map[18]: type Memory, range 64, base 0xcc200000, size 16, enabled
pcib1: requested memory range 0xcc200000-0xcc20ffff: good
	map[20]: type I/O Port, range 32, base 0x4000, size  8, enabled
pcib1: requested I/O range 0x4000-0x40ff: in range
	map[24]: type Memory, range 32, base 0xcc300000, size 20, enabled
pcib1: requested memory range 0xcc300000-0xcc3fffff: good
pcib1: matched entry for 1.5.INTB
pcib1: slot 5 INTB hardwired to IRQ 19
vgapci0: <VGA-compatible display> port 0x4000-0x40ff mem 0xc0000000-0xc7ffffff,0xcc200000-0xcc20ffff,0xcc300000-0xcc3fffff irq 19 at device 5.0 on pci1
drm0: <ATI Radeon RS690 X1270 IGP> on vgapci0
vgapci0: attempting to allocate 1 MSI vectors (1 supported)
msi: routing MSI IRQ 256 to local APIC 0 vector 49
vgapci0: using IRQ 256 for MSI
info: [drm] MSI enabled 1 message(s)
vgapci0: child drm0 requested pci_enable_busmaster
info: [drm] Initialized radeon 1.31.0 20080613
pcib2: <ACPI PCI-PCI bridge> at device 4.0 on pci0
pcib2:   domain            0
pcib2:   secondary bus     16
pcib2:   subordinate bus   16
pcib2:   I/O decode        0xf000-0xfff
pcib2:   memory decode     0xcc000000-0xcc0fffff
pcib2:   no prefetched decode
pcib2: could not get PCI interrupt routing table for \\_SB_.C08B.C24F - AE_NOT_FOUND
pci16: <ACPI PCI bus> on pcib2
pci16: domain=0, physical bus=16
found->	vendor=0x14e4, dev=0x1713, revid=0x02
	domain=0, bus=16, slot=0, func=0
	class=02-00-00, hdrtype=0x00, mfdev=0
	cmdreg=0x0006, statreg=0x0010, cachelnsz=16 (dwords)
	lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
	intpin=a, irq=10
	powerspec 3  supports D0 D3  current D0
	MSI supports 1 message, 64 bit
	map[10]: type Memory, range 64, base 0xcc000000, size 16, enabled
pcib2: requested memory range 0xcc000000-0xcc00ffff: good
pcib0: matched entry for 0.4.INTA
pcib0: slot 4 INTA hardwired to IRQ 16
pcib2: slot 0 INTA is routed to irq 16
bge0: <Broadcom BCM5906 A2, ASIC rev. 0x00c002> mem 0xcc000000-0xcc00ffff irq 16 at device 0.0 on pci16
bge0: attempting to allocate 1 MSI vectors (1 supported)
msi: routing MSI IRQ 257 to local APIC 0 vector 50
bge0: using IRQ 257 for MSI
bge0: CHIP ID 0x0000c002; ASIC REV 0x0c; CHIP REV 0xc0; PCI-E
miibus0: <MII bus> on bge0
brgphy0: <BCM5906 10/100baseTX PHY> PHY 1 on miibus0
brgphy0: OUI 0x000af7, model 0x0004, rev. 0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bge0: bpf attached
bge0: Ethernet address: 00:1a:4b:89:4b:4e
bge0: [MPSAFE]
bge0: [ITHREAD]
pcib3: <ACPI PCI-PCI bridge> at device 5.0 on pci0
pcib3:   domain            0
pcib3:   secondary bus     32
pcib3:   subordinate bus   32
pcib3:   I/O decode        0x2000-0x3fff
pcib3:   memory decode     0xc8000000-0xcbffffff
pcib3:   no prefetched decode
pcib3: could not get PCI interrupt routing table for \\_SB_.C08B.C254 - AE_NOT_FOUND
pci32: <ACPI PCI bus> on pcib3
pci32: domain=0, physical bus=32
atapci0: <ATI IXP600 SATA300 controller> port 0x9000-0x9007,0x9008-0x900b,0x9010-0x9017,0x5018-0x501b,0x5020-0x502f mem 0xcc409000-0xcc4093ff irq 16 at device 18.0 on pci0
ioapic0: routing intpin 16 (PCI IRQ 16) to lapic 0 vector 51
atapci0: [MPSAFE]
atapci0: [ITHREAD]
atapci0: AHCI v1.10 controller with 4 3Gbps ports, PM not supported
atapci0: Caps: 64bit NCQ SNTF MPS ALP AL CLO 3Gbps PMD SSC PSC 32cmd CCC 4ports
ata2: <ATA channel 0> on atapci0
ata2: AHCI reset...
ata2: hardware reset ...
ata2: SATA connect time=10ms status=00000113
ata2: ready wait time=19ms
ata2: software reset port 0...
ata2: ready wait time=0ms
ata2: SIGNATURE: 00000101
ata2: AHCI reset done: devices=00000001
ata2: [MPSAFE]
ata2: [ITHREAD]
ohci0: <OHCI (generic) USB controller> mem 0xcc401000-0xcc401fff irq 23 at device 19.0 on pci0
ioapic0: routing intpin 23 (PCI IRQ 23) to lapic 0 vector 52
ohci0: [MPSAFE]
ohci0: [ITHREAD]
usbus0: <OHCI (generic) USB controller> on ohci0
ohci1: <OHCI (generic) USB controller> mem 0xcc402000-0xcc402fff irq 17 at device 19.1 on pci0
ioapic0: routing intpin 17 (PCI IRQ 17) to lapic 0 vector 53
ohci1: [MPSAFE]
ohci1: [ITHREAD]
usbus1: <OHCI (generic) USB controller> on ohci1
ohci2: <OHCI (generic) USB controller> mem 0xcc403000-0xcc403fff irq 17 at device 19.2 on pci0
ohci2: [MPSAFE]
ohci2: [ITHREAD]
usbus2: <OHCI (generic) USB controller> on ohci2
ohci3: <OHCI (generic) USB controller> mem 0xcc404000-0xcc404fff irq 17 at device 19.3 on pci0
ohci3: [MPSAFE]
ohci3: [ITHREAD]
usbus3: <OHCI (generic) USB controller> on ohci3
ohci4: <OHCI (generic) USB controller> mem 0xcc405000-0xcc405fff irq 17 at device 19.4 on pci0
ohci4: [MPSAFE]
ohci4: [ITHREAD]
usbus4: <OHCI (generic) USB controller> on ohci4
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xcc406000-0xcc4060ff irq 23 at device 19.5 on pci0
ehci0: [MPSAFE]
ehci0: [ITHREAD]
ehci0: AMD SB600/700 quirk applied
ehci0: Dropped interrupts workaround enabled
usbus5: EHCI version 1.0
usbus5: <EHCI (generic) USB 2.0 controller> on ehci0
pci0: <serial bus, SMBus> at device 20.0 (no driver attached)
atapci1: <ATI IXP600 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x5040-0x504f irq 16 at device 20.1 on pci0
ata0: <ATA channel 0> on atapci1
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
ata0: stat1=0x00 err=0x00 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=00 stat1=00 devices=0x10000
ioapic0: routing intpin 14 (ISA IRQ 14) to lapic 0 vector 54
ata0: [MPSAFE]
ata0: [ITHREAD]
hdac0: <ATI SB600 High Definition Audio Controller> irq 16 at device 20.2 on pci0
hdac0: HDA Driver Revision: 20100226_0142
hdac0: Lazy allocation of 0x4000 bytes rid 0x10 type 3 at 0xb7fb0000
hdac0: [MPSAFE]
hdac0: [ITHREAD]
hdac0: hdac_get_capabilities: Invalid corb size (0)
hdac0: Resetting corb size to 256
hdac0: hdac_get_capabilities: Invalid rirb size (0)
hdac0: Resetting rirb size to 256
hdac0: Caps: OSS 0, ISS 0, BSS 0, NSDO 1, CORB 256, RIRB 256
isab0: <PCI-ISA bridge> at device 20.3 on pci0
isa0: <ISA bus> on isab0
pcib4: <ACPI PCI-PCI bridge> at device 20.4 on pci0
pcib4:   domain            0
pcib4:   secondary bus     2
pcib4:   subordinate bus   3
pcib4:   I/O decode        0xf000-0xfff
pcib4:   memory decode     0xcc100000-0xcc1fffff
pcib4:   no prefetched decode
pcib4:   Subtractively decoded bridge.
pci2: <ACPI PCI bus> on pcib4
pci2: domain=0, physical bus=2
found->	vendor=0x1180, dev=0x0476, revid=0xb6
	domain=0, bus=2, slot=4, func=0
	class=06-07-00, hdrtype=0x02, mfdev=1
	cmdreg=0x0007, statreg=0x0210, cachelnsz=0 (dwords)
	lattimer=0x40 (1920 ns), mingnt=0x80 (32000 ns), maxlat=0x07 (1750 ns)
	intpin=a, irq=10
	powerspec 2  supports D0 D1 D2 D3  current D0
	map[10]: type Memory, range 32, base 0xcc100000, size 12, enabled
pcib4: requested memory range 0xcc100000-0xcc100fff: good
pcib4: matched entry for 2.4.INTA
pcib4: slot 4 INTA hardwired to IRQ 20
cbb0: <RF5C476 PCI-CardBus Bridge> mem 0xcc100000-0xcc100fff irq 20 at device 4.0 on pci2
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
ioapic0: routing intpin 20 (PCI IRQ 20) to lapic 0 vector 55
cbb0: [MPSAFE]
cbb0: [FILTER]
cbb0: PCI Configuration space:
  0x00: 0x04761180 0x02100007 0x060700b6 0x00824000 
  0x10: 0xcc100000 0x020000dc 0x20030302 0xfffff000 
  0x20: 0x00000000 0xfffff000 0x00000000 0xfffffffc 
  0x30: 0x00000000 0xfffffffc 0x00000000 0x07000114 
  0x40: 0x30c2103c 0x00000001 0x00000000 0x00000000 
  0x50: 0x00000000 0x00000000 0x00000000 0x00000000 
  0x60: 0x00000000 0x00000000 0x00000000 0x00000000 
  0x70: 0x00000000 0x00000000 0x00000000 0x00000000 
  0x80: 0x30a00001 0x00000000 0x04630463 0x00000000 
  0x90: 0x00000000 0x00000000 0x00000000 0x00000000 
  0xa0: 0x00000008 0x00000000 0x00000000 0x00000000 
  0xb0: 0x00000000 0xbe000000 0x00003000 0x00000000 
  0xc0: 0x30c2103c 0x00000000 0x00000000 0x00000000 
  0xd0: 0x00000000 0x00000000 0x00000000 0xfe0a0001 
  0xe0: 0x24c04000 0x00000000 0x00000000 0x00000000 
  0xf0: 0x00000000 0x00000000 0x00000000 0x00000000 
battery0: <ACPI Control Method Battery> on acpi0
battery1: <ACPI Control Method Battery> on acpi0
acpi_acad0: <AC Adapter> on acpi0
acpi_button0: <Sleep Button> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
attimer0: [MPSAFE]
attimer0: [FILTER]
ioapic0: routing intpin 2 (ISA IRQ 0) to lapic 0 vector 56
Event timer "i8254" frequency 1193182 Hz quality 100
atrtc0: <AT realtime clock> port 0x70-0x71,0x72-0x73 irq 8 on acpi0
atrtc0: registered as a time-of-day clock (resolution 1000000us)
ioapic0: routing intpin 8 (ISA IRQ 8) to lapic 0 vector 57
atrtc0: [MPSAFE]
atrtc0: [FILTER]
Event timer "RTC" frequency 32768 Hz quality 0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
ioapic0: routing intpin 1 (ISA IRQ 1) to lapic 0 vector 58
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: unable to allocate IRQ
psmcpnp0: <PS/2 mouse port> irq 12 on acpi0
psm0: current command byte:0065
psm0: <PS/2 Mouse> irq 12 on atkbdc0
ioapic0: routing intpin 12 (ISA IRQ 12) to lapic 0 vector 59
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model IntelliMouse, device ID 3-00, 3 buttons
psm0: config:00000000, flags:00000008, packet size:4
psm0: syncmask:08, syncbits:00
acpi0: wakeup code va 0xffffff80001f0000 pa 0x4000
isa_probe_children: disabling PnP devices
atkbdc: atkbdc0 already exists; skipping it
atrtc: atrtc0 already exists; skipping it
sc: sc0 already exists; skipping it
isa_probe_children: probing non-PnP devices
orm0: <ISA Option ROM> at iomem 0xd0000-0xd0fff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd1, terminal emulator: scteken (teken terminal)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fdc0 failed to probe at port 0x3f0 irq 6 drq 2 on isa0
ppc0 failed to probe at irq 7 on isa0
uart0: <ns8250> failed to probe at port 0x3f8-0x3ff irq 4 on isa0
uart1: <ns8250> failed to probe at port 0x2f8-0x2ff irq 3 on isa0
isa_probe_children: probing PnP devices
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_throttle0: P_CNT from P_BLK 0x8010
powernow0: <PowerNow! K8> on cpu0
acpi_throttle1: <ACPI CPU Throttling> on cpu1
acpi_throttle1: failed to attach P_CNT
device_attach: acpi_throttle1 attach returned 6
powernow1: <PowerNow! K8> on cpu1
Device configuration finished.
Reducing kern.maxvnodes 187974 -> 100000
procfs registered
ZFS NOTICE: Prefetch is disabled by default if less than 4GB of RAM is present;
            to enable, add "vfs.zfs.prefetch_disable=0" to /boot/loader.conf.
ZFS filesystem version 4
ZFS storage pool version 15
Timecounter "TSC" frequency 1994947870 Hz quality -100
Starting kernel event timers: LAPIC @ 1000Hz, i8254 @ 127Hz
lapic: Divisor 2, Frequency 99747427 Hz
Timecounters tick every 1.000 msec
vlan: initialized, using hash tables with chaining
IP Filter: v4.1.28 initialized.  Default = block all, Logging = enabled
lo0: bpf attached
ata0: Identifying devices: 00010000
ata0: New devices: 00010000
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 12Mbps Full Speed USB v1.0
usbus5: 480Mbps High Speed USB v2.0
acpi_tz0: _AC3: temperature 52.0 >= setpoint 40.0
acpi_tz0: _AC2: temperature 52.0 >= setpoint 50.0
acpi_tz0: switched from NONE to _AC2: 52.0C
battery0: battery initialization start
ugen0.1: <ATI> at usbus0
uhub0: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <ATI> at usbus1
uhub1: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <ATI> at usbus2
uhub2: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
ugen3.1: <ATI> at usbus3
uhub3: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
ugen4.1: <ATI> at usbus4
uhub4: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
ugen5.1: <ATI> at usbus5
uhub5: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus5
battery1: battery initialization start
acpi_acad0: acline initialization start
ata0-master: pio=PIO4 wdma=WDMA2 udma=UNSUPPORTED cable=80 wire
acd0: setting PIO4
acd0: <MATSHITADVD-RAM UJ-861H/1.50> DVDR drive at ata0 as master
acd0: read 4134KB/s (4134KB/s) write 4134KB/s (4134KB/s), 2048KB buffer, PIO4 
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet
acd0: Writes: CDR, CDRW, DVDR, DVDRAM, test write, burnproof
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
ata2: Identifying devices: 00000001
ata2: New devices: 00000001
ata2-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=40 wire
ad4: setting UDMA100
ad4: 152627MB <Seagate ST9160821AS 3.BHE> at ata2-master UDMA100 SATA 1.5Gb/s
ad4: 312581808 sectors [310101C/16H/63S] 16 sectors/interrupt 1 depth queue
hdac0: 
SMP: AP CPU #1 Launched!
cpu1 AP:
     ID: 0x01000000   VER: 0x80050010 LDR: 0x00000000 DFR: 0xffffffff
  lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
  timer: 0x000100ef therm: 0x00010000 err: 0x000000f0 pmc: 0x00010400
   cmci: 0x00000000
ioapic0: routing intpin 1 (CPU1: local APIC error 0x80ISA IRQ 1
) to lapic 1 vector 48
ioapic0: routing intpin 12 (ISA IRQ 12) to lapic 1 vector 49
ioapic0: routing intpin 16 (PCI IRQ 16) to lapic 1 vector 50
ioapic0: routing intpin 20 (PCI IRQ 20) to lapic 1 vector 51
msi: Assigning MSI IRQ 257 to local APIC 1 vector 52
WARNING: WITNESS option enabled, expect reduced performance.
GEOM: new disk ad4
acpi_acad0: On Line
acpi_acad0: acline initialization done, tried 1 times
battery0: battery initialization done, tried 1 times
acpi_tz0: _AC3: temperature 52.0 >= setpoint 40.0
acpi_tz0: _AC3: temperature 52.0 >= setpoint 40.0
acpi_tz0: switched from _AC2 to _AC3: 52.0C
Root mount waiting for: usbus5 usbus4 usbus3 usbus2 usbus1 usbus0
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
uhub4: 2 ports with 2 removable, self powered
Event timer "i8254" is dead.
Starting kernel event timers: LAPIC @ 1000Hz, RTC @ 128Hz
Root mount waiting for: usbus5
Root mount waiting for: usbus5
Root mount waiting for: usbus5
acd0: FAILURE - INQUIRY ILLEGAL REQUEST asc=0x24 ascq=0x00 
(probe0:ata0:0:0:0): SCSI status error
(probe0:ata0:0:0:0): INQUIRY. CDB: 12 1 0 0 ff 0 
(probe0:ata0:0:0:0): CAM status: SCSI Status Error
(probe0:ata0:0:0:0): SCSI status: Check Condition
(probe0:ata0:0:0:0): SCSI sense: ILLEGAL REQUEST asc:24,0 (Invalid field in CDB)
(probe0:ata0:0:0:0): Error 22, Unretryable error
(probe0:ata0:0:0:0): Down reving Protocol Version from 2 to 0?
Root mount waiting for: usbus5
uhub5: 10 ports with 10 removable, self powered
(probe0:ata0:0:0:0): SCSI status error
(probe0:ata0:0:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 
(probe0:ata0:0:0:0): CAM status: SCSI Status Error
(probe0:ata0:0:0:0): SCSI status: Check Condition
(probe0:ata0:0:0:0): SCSI sense: NOT READY asc:3a,1 (Medium not present - tray closed)
(probe0:ata0:0:0:0): Error 6, Unretryable error
GEOM: new disk cd0
pass0 at ata0 bus 0 scbus0 target 0 lun 0
pass0: <MATSHITA DVD-RAM UJ-861H 1.50> Removable CD-ROM SCSI-0 device 
pass0: 16.000MB/s transfers
(cd0:ata0:0:0:0): SCSI status error
(cd0:ata0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0 
(cd0:ata0:0:0:0): CAM status: SCSI Status Error
(cd0:ata0:0:0:0): SCSI status: Check Condition
(cd0:ata0:0:0:0): SCSI sense: NOT READY asc:3a,1 (Medium not present - tray closed)
(cd0:ata0:0:0:0): Error 6, Unretryable error
cd0 at ata0 bus 0 scbus0 target 0 lun 0
cd0: <MATSHITA DVD-RAM UJ-861H 1.50> Removable CD-ROM SCSI-0 device 
cd0: 16.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present - tray closed
(cd0:ata0:0:0:0): SCSI status error
(cd0:ata0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0 
(cd0:ata0:0:0:0): CAM status: SCSI Status Error
(cd0:ata0:0:0:0): SCSI status: Check Condition
(cd0:ata0:0:0:0): SCSI sense: NOT READY asc:3a,1 (Medium not present - tray closed)
(cd0:ata0:0:0:0): Error 6, Unretryable error
(cd0:ata0:0:0:0): SCSI status error
(cd0:ata0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0 
(cd0:ata0:0:0:0): CAM status: SCSI Status Error
(cd0:ata0:0:0:0): SCSI status: Check Condition
(cd0:ata0:0:0:0): SCSI sense: NOT READY asc:3a,1 (Medium not present - tray closed)
(cd0:ata0:0:0:0): Error 6, Unretryable error
Trying to mount root from ufs:/dev/ad4s1a
ct_to_ts([2010-07-30 13:57:23]) = 1280498243.000000000
start_init: trying /sbin/init
ugen0.2: <Broadcom Corp> at usbus0
ugen1.2: <vendor 0x0430> at usbus1
ums0: <vendor 0x0430 product 0x0100, class 0/0, rev 2.00/1.07, addr 2> on usbus1
ums0: 3 buttons and [XY] coordinates ID=0
bge0: link UP
bge0: link state changed to UP


-- 
Anton Shterenlikht
Room 2.6, Queen's Building
Mech Eng Dept
Bristol University
University Walk, Bristol BS8 1TR, UK
Tel: +44 (0)117 331 5944
Fax: +44 (0)117 929 4423



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20100730130237.GA9853>