Date: Tue, 26 Feb 2008 14:34:23 +0900 From: Pyun YongHyeon <pyunyh@gmail.com> To: Mike Tancsa <mike@sentex.net> Cc: freebsd-current@freebsd.org Subject: Re: CFT: vr(4) Message-ID: <20080226053423.GB47750@cdnetworks.co.kr> In-Reply-To: <200802260503.m1Q53Jm3050738@lava.sentex.ca> References: <20080204022334.GC27999@cdnetworks.co.kr> <20080217112104.X80805@fledge.watson.org> <200802171458.26951.freebsd-current@dino.sk> <200802171517.26965.freebsd-current@dino.sk> <20080218081801.GB14601@cdnetworks.co.kr> <20080222054356.GE30497@cdnetworks.co.kr> <200802260503.m1Q53Jm3050738@lava.sentex.ca>
next in thread | previous in thread | raw e-mail | index | archive | help
On Tue, Feb 26, 2008 at 12:03:29AM -0500, Mike Tancsa wrote: > At 12:43 AM 2/22/2008, Pyun YongHyeon wrote: > > > > > > I've put up a new version under the old URL. > > > It's not tested in sparc64 but it seems to work on i386. > > > Would you give it spin? > > > > > > >Any progress here? Does the updated one works on your box? > > > So far so good on my Soekris hardware. I will try some vlan tests tomorrow. > > pci0: <encrypt/decrypt, entertainment crypto> at device 1.2 (no > driver attached) > vr0: <VIA VT6105M Rhine III 10/100BaseTX> port 0xe100-0xe1ff mem > 0xa0004000-0xa00040ff irq 11 at device 6.0 on pci0 > vr0: Quirks: 0x6 > vr0: Revision: 0x96 > miibus0: <MII bus> on vr0 > ukphy0: <Generic IEEE 802.3u media interface> PHY 1 on miibus0 > ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > vr0: Ethernet address: 00:00:24:c9:34:88 > vr0: [ITHREAD] > vr1: <VIA VT6105M Rhine III 10/100BaseTX> port 0xe200-0xe2ff mem > 0xa0004100-0xa00041ff irq 5 at device 7.0 on pci0 > vr1: Quirks: 0x6 > vr1: Revision: 0x96 > miibus1: <MII bus> on vr1 > ukphy1: <Generic IEEE 802.3u media interface> PHY 1 on miibus1 > ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > vr1: Ethernet address: 00:00:24:c9:34:89 > vr1: [ITHREAD] > vr2: <VIA VT6105M Rhine III 10/100BaseTX> port 0xe300-0xe3ff mem > 0xa0004200-0xa00042ff irq 9 at device 8.0 on pci0 > vr2: Quirks: 0x6 > vr2: Revision: 0x96 > miibus2: <MII bus> on vr2 > ukphy2: <Generic IEEE 802.3u media interface> PHY 1 on miibus2 > ukphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > vr2: Ethernet address: 00:00:24:c9:34:8a > vr2: [ITHREAD] > vr3: <VIA VT6105M Rhine III 10/100BaseTX> port 0xe400-0xe4ff mem > 0xa0004300-0xa00043ff irq 12 at device 9.0 on pci0 > vr3: Quirks: 0x6 > vr3: Revision: 0x96 > miibus3: <MII bus> on vr3 > ukphy3: <Generic IEEE 802.3u media interface> PHY 1 on miibus3 > ukphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > vr3: Ethernet address: 00:00:24:c9:34:8b > vr3: [ITHREAD] > > This is 7.0-PRERELEASE #0: Mon Feb 25 11:25:31 EST 2008 > > ---Mike > Thanks again for your testing! An unresolved issue for Milan Obuch's router board still prevent me from committing the overhauled one. Unfortunately I still have no clue why his hardware does not work even though it has the same hardware revision(0x96). -- Regards, Pyun YongHyeon
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20080226053423.GB47750>