Date: Fri, 25 Mar 2005 11:46:18 +0200 From: Ruslan Ermilov <ru@freebsd.org> To: Dag-Erling Sm?rgrav <des@des.no> Cc: amd64@freebsd.org Subject: Re: testers wanted Message-ID: <20050325094618.GA76747@ip.net.ua> In-Reply-To: <86ll8dgnx3.fsf@xps.des.no> References: <86ll8dgnx3.fsf@xps.des.no>
next in thread | previous in thread | raw e-mail | index | archive | help
--yNb1oOkm5a9FJOVX
Content-Type: multipart/mixed; boundary="8t9RHnE3ZwKMSgU+"
Content-Disposition: inline
--8t9RHnE3ZwKMSgU+
Content-Type: text/plain; charset=us-ascii
Content-Disposition: inline
Content-Transfer-Encoding: quoted-printable
Hi DES,
On Thu, Mar 24, 2005 at 02:43:04PM +0100, Dag-Erling Sm?rgrav wrote:
> I need someone with an nForce3-based Opteron box running -CURRENT to
> do the following:
>=20
> - upgrade to a recent -CURRENT, verify that a GENERIC kernel with
> NO_MIXED_MODE removed works properly *with apic enabled*
>=20
Looks like it works, though I got one TIMEOUT - WRITE_DMA with it.
I just used a stripped down GENERIC kernel with hw.apic.mixed_mode=3D1
set in /boot/loader.conf, which has the same effect as above.
> - build an unmodified GENERIC (*with* NO_MIXED_MODE) from the same
> sources and boot it *with apic enabled*
>=20
Booted the same kernel with hw.apic.mixed_mode=3D0. It stalls
(see the attached logs).
> Please provide verbose dmesg for both cases, as well as the contents
> of /boot/loader.conf and /boot/device.hints.
>=20
/boot/loader.conf has some uninteresting stuff to load network
and sound modules I need, and device.hints equals GENERIC.hints.
Cheers,
--=20
Ruslan Ermilov
ru@FreeBSD.org
FreeBSD committer
--8t9RHnE3ZwKMSgU+
Content-Type: text/plain; charset=us-ascii
Content-Disposition: attachment; filename="dmesg.boot.mixed_mode"
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 6.0-CURRENT #3: Fri Mar 25 10:44:58 EET 2005
ru@hammer.runet:/usr/obj/usr/src/sys/HAMMER
WARNING: WITNESS option enabled, expect reduced performance.
Preloaded elf kernel "/boot/kernel/kernel" at 0xffffffff8068b000.
Preloaded elf obj module "/boot/kernel/if_em.ko" at 0xffffffff8068b1d0.
Preloaded elf obj module "/boot/kernel/if_xl.ko" at 0xffffffff8068b6f8.
Preloaded elf obj module "/boot/kernel/miibus.ko" at 0xffffffff8068bc20.
Preloaded elf obj module "/boot/kernel/snd_ich.ko" at 0xffffffff8068c148.
Preloaded elf obj module "/boot/kernel/sound.ko" at 0xffffffff8068c6b0.
ACPI APIC Table: <A M I OEMAPIC >
Calibrating clock(s) ... i8254 clock: 1193171 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 1470007451 Hz
CPU: AMD Opteron(tm) Processor 240 (1470.01-MHz K8-class CPU)
Origin = "AuthenticAMD" Id = 0xf51 Stepping = 1
Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2>
AMD Features=0xe0500800<SYSCALL,NX,MMX+,LM,3DNow+,3DNow>
L1 2MB data TLB: 8 entries, fully associative
L1 2MB instruction TLB: 8 entries, fully associative
L1 4KB data TLB: 32 entries, fully associative
L1 4KB instruction TLB: 32 entries, fully associative
L1 data cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L1 instruction cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L2 2MB unified TLB: 0 entries, disabled/not present
L2 4KB data TLB: 512 entries, 4-way associative
L2 4KB instruction TLB: 512 entries, 4-way associative
L2 unified cache: 1024 kbytes, 64 bytes/line, 1 lines/tag, 16-way associative
real memory = 1073479680 (1023 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009bfff, 634880 bytes (155 pages)
0x0000000000789000 - 0x000000003e189fff, 1033900032 bytes (252417 pages)
avail memory = 1028120576 (980 MB)
APIC: CPU 0 has ACPI ID 1
MADT: Found IO APIC ID 1, Interrupt 0 at 0xfec00000
ioapic0: Routing external 8259A's -> intpin 0
ioapic0: intpin 0 -> ExtINT (edge, high)
ioapic0: intpin 1 -> ISA IRQ 1 (edge, high)
ioapic0: intpin 2 -> ISA IRQ 2 (edge, high)
ioapic0: intpin 3 -> ISA IRQ 3 (edge, high)
ioapic0: intpin 4 -> ISA IRQ 4 (edge, high)
ioapic0: intpin 5 -> ISA IRQ 5 (edge, high)
ioapic0: intpin 6 -> ISA IRQ 6 (edge, high)
ioapic0: intpin 7 -> ISA IRQ 7 (edge, high)
ioapic0: intpin 8 -> ISA IRQ 8 (edge, high)
ioapic0: intpin 9 -> ISA IRQ 9 (edge, high)
ioapic0: intpin 10 -> ISA IRQ 10 (edge, high)
ioapic0: intpin 11 -> ISA IRQ 11 (edge, high)
ioapic0: intpin 12 -> ISA IRQ 12 (edge, high)
ioapic0: intpin 13 -> ISA IRQ 13 (edge, high)
ioapic0: intpin 14 -> ISA IRQ 14 (edge, high)
ioapic0: intpin 15 -> ISA IRQ 15 (edge, high)
ioapic0: intpin 16 -> PCI IRQ 16 (level, low)
ioapic0: intpin 17 -> PCI IRQ 17 (level, low)
ioapic0: intpin 18 -> PCI IRQ 18 (level, low)
ioapic0: intpin 19 -> PCI IRQ 19 (level, low)
ioapic0: intpin 20 -> PCI IRQ 20 (level, low)
ioapic0: intpin 21 -> PCI IRQ 21 (level, low)
ioapic0: intpin 22 -> PCI IRQ 22 (level, low)
ioapic0: intpin 23 -> PCI IRQ 23 (level, low)
MADT: Interrupt override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
ioapic0: intpin 2 trigger: edge
ioapic0: intpin 2 polarity: high
MADT: Interrupt override: source 9, irq 9
ioapic0: intpin 9 trigger: level
ioapic0: intpin 9 polarity: high
MADT: Interrupt override: source 14, irq 14
ioapic0: intpin 14 trigger: edge
ioapic0: intpin 14 polarity: high
MADT: Interrupt override: source 15, irq 15
ioapic0: intpin 15 trigger: edge
ioapic0: intpin 15 polarity: high
ioapic0 <Version 1.1> irqs 0-23 on motherboard
cpu0 BSP:
ID: 0x00000000 VER: 0x00040010 LDR: 0x01000000 DFR: 0x0fffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000100ef therm: 0x00000000 err: 0x0001000f pcm: 0x00010000
random: <entropy source, Software, Yarrow>
io: <I/O>
mem: <memory>
null: <null device, zero device>
acpi0: <A M I OEMXSDT> on motherboard
acpi0: [MPSAFE]
pci_open(1): mode 1 addr port (0x0cf8) is 0x80015004
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=00d110de)
AcpiOsDerivePciId: bus 0 dev 1 func 0
acpi0: Power Button (fixed)
ACPI timer: 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 -> 10
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0
cpu0: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci_link0: <ACPI PCI Link LKSM> irq 0 on acpi0
pci_link0: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 22
pci_link0: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 22
pci_link0: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 22
pci_link1: <ACPI PCI Link LUS0> irq 11 on acpi0
pci_link1: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 11 N 0 20
pci_link1: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 20
pci_link1: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 20
pci_link2: <ACPI PCI Link LAUI> irq 5 on acpi0
pci_link2: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 5 N 0 21
pci_link2: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 21
pci_link2: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 21
pci_link3: <ACPI PCI Link LKMO> irq 0 on acpi0
pci_link3: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 21
pci_link3: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 21
pci_link3: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 21
pci_link4: <ACPI PCI Link LUS1> irq 5 on acpi0
pci_link4: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 5 N 0 20
pci_link4: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 20
pci_link4: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 20
pci_link5: <ACPI PCI Link LUS2> irq 10 on acpi0
pci_link5: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 10 N 0 20
pci_link5: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 20
pci_link5: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 20
pci_link6: <ACPI PCI Link LNKE> irq 11 on acpi0
pci_link6: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 11 N 0 16
pci_link6: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 16
pci_link6: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 16
pci_link7: <ACPI PCI Link LKLN> irq 0 on acpi0
pci_link7: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 21
pci_link7: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 21
pci_link7: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 21
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
map[10]: type 3, range 32, base f0000000, size 27, enabled
found-> vendor=0x10de, dev=0x00d1, revid=0xa4
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x10de, dev=0x00d0, revid=0xf6
bus=0, slot=1, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x000f, statreg=0x00a0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[20]: type 4, range 32, base 00005000, size 6, enabled
map[24]: type 4, range 32, base 00005040, size 6, enabled
found-> vendor=0x10de, dev=0x00d4, revid=0xa4
bus=0, slot=1, func=1
class=0c-05-00, hdrtype=0x00, mfdev=1
cmdreg=0x0001, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
intpin=a, irq=255
powerspec 2 supports D0 D3 current D0
map[10]: type 1, range 32, base febfd000, size 12, enabled
pcib0: matched entry for 0.2.INTA (src \\_SB_.LUS0:0)
pci_link1: Picked IRQ 20 with weight 0
ioapic0: Changing polarity for pin 20 to high
pcib0: slot 2 INTA routed to irq 20 via \\_SB_.LUS0
found-> vendor=0x10de, dev=0x00d7, revid=0xa5
bus=0, slot=2, func=0
class=0c-03-10, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
intpin=a, irq=20
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base febfe000, size 12, enabled
pcib0: matched entry for 0.2.INTB (src \\_SB_.LUS1:0)
pci_link4: Picked IRQ 20 with weight 1
pcib0: slot 2 INTB routed to irq 20 via \\_SB_.LUS1
found-> vendor=0x10de, dev=0x00d7, revid=0xa5
bus=0, slot=2, func=1
class=0c-03-10, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
intpin=b, irq=20
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base febffc00, size 8, enabled
pcib0: matched entry for 0.2.INTC (src \\_SB_.LUS2:0)
pci_link5: Picked IRQ 20 with weight 2
pcib0: slot 2 INTC routed to irq 20 via \\_SB_.LUS2
found-> vendor=0x10de, dev=0x00d8, revid=0xa2
bus=0, slot=2, func=2
class=0c-03-20, hdrtype=0x00, mfdev=1
cmdreg=0x0006, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
intpin=c, irq=20
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 0000e800, size 8, enabled
map[14]: type 4, range 32, base 0000ec00, size 7, enabled
map[18]: type 1, range 32, base febfb000, size 12, enabled
pcib0: matched entry for 0.6.INTA (src \\_SB_.LAUI:0)
pci_link2: Picked IRQ 21 with weight 0
ioapic0: Changing polarity for pin 21 to high
pcib0: slot 6 INTA routed to irq 21 via \\_SB_.LAUI
found-> vendor=0x10de, dev=0x00da, revid=0xa2
bus=0, slot=6, func=0
class=04-01-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x05 (1250 ns)
intpin=a, irq=21
powerspec 2 supports D0 D1 D2 D3 current D0
map[20]: type 4, range 32, base 0000ffa0, size 4, enabled
found-> vendor=0x10de, dev=0x00d5, revid=0xa5
bus=0, slot=8, func=0
class=01-01-8a, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
powerspec 2 supports D0 D3 current D0
found-> vendor=0x10de, dev=0x00dd, revid=0xa2
bus=0, slot=10, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x00a0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns)
found-> vendor=0x10de, dev=0x00d2, revid=0xa4
bus=0, slot=11, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x0220, cachelnsz=0 (dwords)
lattimer=0x10 (480 ns), mingnt=0x0b (2750 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x1100, revid=0x00
bus=0, slot=24, func=0
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x1101, revid=0x00
bus=0, slot=24, func=1
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x1102, revid=0x00
bus=0, slot=24, func=2
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x1103, revid=0x00
bus=0, slot=24, func=3
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
isab0: <PCI-ISA bridge> at device 1.0 on pci0
isa0: <ISA bus> on isab0
pci0: <serial bus, SMBus> at device 1.1 (no driver attached)
pci0:1:1: Transition from D0 to D3
ohci0: <nVidia nForce3 USB Controller> mem 0xfebfd000-0xfebfdfff irq 20 at device 2.0 on pci0
ohci0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfebfd000
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <nVidia nForce3 USB Controller> on ohci0
usb0: USB revision 1.0
uhub0: nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
ohci1: <nVidia nForce3 USB Controller> mem 0xfebfe000-0xfebfefff irq 20 at device 2.1 on pci0
ohci1: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfebfe000
ohci1: [GIANT-LOCKED]
usb1: OHCI version 1.0, legacy support
usb1: SMM does not respond, resetting
usb1: <nVidia nForce3 USB Controller> on ohci1
usb1: USB revision 1.0
uhub1: nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 3 ports with 3 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfebffc00-0xfebffcff irq 20 at device 2.2 on pci0
ehci0: Reserved 0x100 bytes for rid 0x10 type 3 at 0xfebffc00
ehci0: [GIANT-LOCKED]
usb2: waiting for BIOS to give up control
usb2: timed out waiting for BIOS
usb2: EHCI version 1.0
usb2: companion controllers, 4 ports each: usb0 usb1
usb2: <EHCI (generic) USB 2.0 controller> on ehci0
usb2: USB revision 2.0
uhub2: nVidia EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 6 ports with 6 removable, self powered
pcm0: <nVidia nForce3> port 0xe800-0xe8ff,0xec00-0xec7f mem 0xfebfb000-0xfebfbfff irq 21 at device 6.0 on pci0
pcm0: Reserved 0x100 bytes for rid 0x10 type 4 at 0xe800
pcm0: Reserved 0x80 bytes for rid 0x14 type 4 at 0xec00
pcm0: [GIANT-LOCKED]
pcm0: <Avance Logic ALC650 AC97 Codec (id = 0x414c4720)>
pcm0: Codec features 20 bit DAC, 18 bit ADC, 5 bit master volume, Realtek 3D Stereo Enhancement
pcm0: Primary codec extended features variable rate PCM, double rate PCM, reserved 1, center DAC, surround DAC, LFE DAC, reserved 4
pcm0: sndbuf_setmap 3db86000, 4000; 0xffffffffa5446000 -> 3db86000
pcm0: sndbuf_setmap 3db78000, 4000; 0xffffffffa544a000 -> 3db78000
atapci0: <nVidia nForce3 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 8.0 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xffa0
ata0: channel #0 on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0-master: stat=0x90 err=0x90 lsb=0x90 msb=0x90
ata0-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata0-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata0: [MPSAFE]
ata1: channel #1 on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=03 ostat0=7f ostat1=50
ata1-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-slave: stat=0x10 err=0x01 lsb=0x14 msb=0xeb
ata1: reset tp2 stat0=ff stat1=10 devices=0x8<ATAPI_SLAVE>
ata1: [MPSAFE]
pcib1: <ACPI PCI-PCI bridge> at device 10.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xc000-0xdfff
pcib1: memory decode 0xfc800000-0xfc9fffff
pcib1: prefetched decode 0xfff00000-0xfffff
pci_link8: <ACPI PCI Link LNKA> irq 11 on acpi0
pci_link8: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 11 N 0 17
pci_link8: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 17
pci_link8: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 17
pci_link9: <ACPI PCI Link LNKB> irq 0 on acpi0
pci_link9: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 18
pci_link9: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 18
pci_link9: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 18
pci_link10: <ACPI PCI Link LNKC> irq 10 on acpi0
pci_link10: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 10 N 0 19
pci_link10: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 19
pci_link10: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 19
pci_link11: <ACPI PCI Link LNKD> irq 0 on acpi0
pci_link11: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 17
pci_link11: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 17
pci_link11: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 17
ACPI: Found matching pin for 0.6.INTA at func 0: 21
pci_link11: BIOS IRQ 21 for 0.6.INTA is invalid
pci1: <ACPI PCI bus> on pcib1
pci1: physical bus=1
map[10]: type 4, range 32, base 0000dc00, size 7, enabled
pcib1: (null) requested I/O range 0xdc00-0xdc7f: in range
map[14]: type 1, range 32, base fc9ffc00, size 7, enabled
pcib1: (null) requested memory range 0xfc9ffc00-0xfc9ffc7f: good
pcib1: matched entry for 1.5.INTA (src \\_SB_.LNKC:0)
pci_link10: Picked IRQ 19 with weight 0
ioapic0: Changing polarity for pin 19 to high
pcib1: slot 5 INTA routed to irq 19 via \\_SB_.LNKC
found-> vendor=0x10b7, dev=0x9200, revid=0x74
bus=1, slot=5, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0117, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x0a (2500 ns), maxlat=0x0a (2500 ns)
intpin=a, irq=19
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base fc9a0000, size 17, enabled
pcib1: (null) requested memory range 0xfc9a0000-0xfc9bffff: good
map[14]: type 1, range 32, base fc980000, size 17, enabled
pcib1: (null) requested memory range 0xfc980000-0xfc99ffff: good
map[18]: type 4, range 32, base 0000d800, size 6, enabled
pcib1: (null) requested I/O range 0xd800-0xd83f: in range
pcib1: matched entry for 1.7.INTA (src \\_SB_.LNKA:0)
pci_link8: Picked IRQ 17 with weight 0
ioapic0: Changing polarity for pin 17 to high
pcib1: slot 7 INTA routed to irq 17 via \\_SB_.LNKA
found-> vendor=0x8086, dev=0x1076, revid=0x00
bus=1, slot=7, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0117, statreg=0x0230, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0xff (63750 ns), maxlat=0x00 (0 ns)
intpin=a, irq=17
powerspec 2 supports D0 D3 current D0
MSI supports 1 message, 64 bit
map[10]: type 4, range 32, base 0000d400, size 6, enabled
pcib1: (null) requested I/O range 0xd400-0xd43f: in range
map[14]: type 4, range 32, base 0000d000, size 4, enabled
pcib1: (null) requested I/O range 0xd000-0xd00f: in range
map[18]: type 4, range 32, base 0000cc00, size 7, enabled
pcib1: (null) requested I/O range 0xcc00-0xcc7f: in range
map[1c]: type 1, range 32, base fc9fe000, size 12, enabled
pcib1: (null) requested memory range 0xfc9fe000-0xfc9fefff: good
map[20]: type 1, range 32, base fc940000, size 17, enabled
pcib1: (null) requested memory range 0xfc940000-0xfc95ffff: good
pcib1: matched entry for 1.8.INTA (src \\_SB_.LNKC:0)
pcib1: slot 8 INTA routed to irq 19 via \\_SB_.LNKC
found-> vendor=0x105a, dev=0x3373, revid=0x02
bus=1, slot=8, func=0
class=01-04-00, hdrtype=0x00, mfdev=0
cmdreg=0x0117, statreg=0x0230, cachelnsz=145 (dwords)
lattimer=0x60 (2880 ns), mingnt=0x04 (1000 ns), maxlat=0x12 (4500 ns)
intpin=a, irq=19
powerspec 2 supports D0 D1 D3 current D0
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xdc00-0xdc7f mem 0xfc9ffc00-0xfc9ffc7f irq 19 at device 5.0 on pci1
xl0: Reserved 0x80 bytes for rid 0x14 type 3 at 0xfc9ffc00
xl0: using memory mapped I/O
xl0: media options word: a
xl0: found MII/AUTO
miibus0: <MII bus> on xl0
xlphy0: <3c905C 10/100 internal PHY> on miibus0
xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl0: bpf attached
xl0: Ethernet address: 00:50:da:42:6e:8e
xl0: [MPSAFE]
em0: <Intel(R) PRO/1000 Network Connection, Version - 1.7.35> port 0xd800-0xd83f mem 0xfc9a0000-0xfc9bffff,0xfc980000-0xfc99ffff irq 17 at device 7.0 on pci1
em0: Reserved 0x20000 bytes for rid 0x10 type 3 at 0xfc9a0000
em0: Reserved 0x40 bytes for rid 0x18 type 4 at 0xd800
em0: [MPSAFE]
em0: bpf attached
em0: Ethernet address: 00:0e:0c:37:c2:82
em0: Speed:N/A Duplex:N/A
atapci1: <Promise PDC20378 SATA150 controller> port 0xd400-0xd43f,0xd000-0xd00f,0xcc00-0xcc7f mem 0xfc9fe000-0xfc9fefff,0xfc940000-0xfc95ffff irq 19 at device 8.0 on pci1
atapci1: failed: rid 0x20 is memory, requested 4
atapci1: Reserved 0x20000 bytes for rid 0x20 type 3 at 0xfc940000
atapci1: Reserved 0x1000 bytes for rid 0x1c type 3 at 0xfc9fe000
atapci1: [MPSAFE]
ata2: channel #0 on atapci1
ata2: reset tp1 mask=01 ostat0=7f ostat1=7f
ata2-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata2-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata2-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata2-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata2-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata2-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata2-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata2: reset tp2 stat0=ff stat1=00 devices=0x0
ata2: [MPSAFE]
ata3: channel #1 on atapci1
ata3: reset tp1 mask=01 ostat0=7f ostat1=7f
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3: reset tp2 stat0=ff stat1=00 devices=0x0
ata3: [MPSAFE]
ata4: channel #2 on atapci1
ata4: reset tp1 mask=03 ostat0=50 ostat1=00
ata4-master: stat=0x90 err=0x90 lsb=0x90 msb=0x90
ata4-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata4-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00
ata4: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata4: [MPSAFE]
pcib2: <ACPI PCI-PCI bridge> at device 11.0 on pci0
pcib2: secondary bus 2
pcib2: subordinate bus 2
pcib2: I/O decode 0xf000-0xfff
pcib2: memory decode 0xfca00000-0xfeafffff
pcib2: prefetched decode 0xe4700000-0xec6fffff
pcib2: could not get PCI interrupt routing table for \\_SB_.PCI0.P0P2 - AE_NOT_FOUND
pci2: <ACPI PCI bus> on pcib2
pci2: physical bus=2
map[10]: type 1, range 32, base fd000000, size 24, enabled
pcib2: (null) requested memory range 0xfd000000-0xfdffffff: good
map[14]: type 3, range 32, base e8000000, size 26, enabled
pcib2: (null) requested memory range 0xe8000000-0xebffffff: good
pcib0: matched entry for 0.11.INTA (src \\_SB_.LNKE:0)
pci_link6: Picked IRQ 16 with weight 0
ioapic0: Changing polarity for pin 16 to high
pcib0: slot 11 INTA routed to irq 16 via \\_SB_.LNKE
pcib2: slot 0 INTA is routed to irq 16
found-> vendor=0x10de, dev=0x0181, revid=0xc1
bus=2, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x02b0, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x05 (1250 ns), maxlat=0x01 (250 ns)
intpin=a, irq=16
powerspec 2 supports D0 D3 current D0
pci2: <display, VGA> at device 0.0 (no driver attached)
acpi_button0: <Power Button> on acpi0
pci_link12: <ACPI PCI Link LTID> irq 0 on acpi0
pci_link12: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 22
pci_link12: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 22
pci_link12: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 22
pci_link13: <ACPI PCI Link LATA> irq 14 on acpi0
pci_link13: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 14 N 0 22
pci_link13: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 22
pci_link13: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 22
fdc0: <floppy drive controller (FDE)> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: ic_type 90 part_id 80
fdc0: [MPSAFE]
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
atkbd0: [GIANT-LOCKED]
psm0: unable to allocate IRQ
psmcpnp0: <PS/2 mouse port> irq 12 on acpi0
psm0: current command byte:0065
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model IntelliMouse, device ID 3-00, 3 buttons
psm0: config:00000000, flags:00000008, packet size:4
psm0: syncmask:08, syncbits:00
sio0: irq maps: 0xc21 0xc31 0xc21 0xc21
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
sio1: irq maps: 0xc21 0xc29 0xc21 0xc21
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
atkbdc: atkbdc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
sc: sc0 already exists; skipping it
sio: sio0 already exists; skipping it
sio: sio1 already exists; skipping it
vga: vga0 already exists; skipping it
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <ISA Option ROMs> at iomem 0xc0000-0xcf7ff,0xcf800-0xcffff,0xd0000-0xd0fff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
ppc0 failed to probe at irq 7 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
isa_probe_children: probing PnP devices
Device configuration finished.
Timecounter "TSC" frequency 1470007451 Hz quality 800
Timecounters tick every 1.000 msec
Linux ELF exec handler installed
lo0: bpf attached
ata0-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
ata0-master: setting PIO4 on nVidia nForce3 chip
ata0-master: setting UDMA100 on nVidia nForce3 chip
ad0: <ST380011A/3.04> ATA-6 disk at ata0-master
ad0: 76319MB (156301488 sectors), 155061 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA100
ata1-slave: pio=0x0c wdma=0x22 udma=0x44 cable=40pin
ata1-slave: setting PIO4 on nVidia nForce3 chip
ata1-slave: DMA limited to UDMA33, non-ATA66 cable or device
ata1-slave: setting UDMA33 on nVidia nForce3 chip
acd0: <COM4824/VER 1.01> CDRW drive at ata1 as slave
acd0: read 345KB/s (8251KB/s) write 8251KB/s (8251KB/s), 2048KB buffer, UDMA33
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, packet
acd0: Writes: CDR, CDRW, test write, burnproof
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
ata4-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
ad8: <ST380011A/3.04> ATA-6 disk at ata4-master
ad8: 76319MB (156301488 sectors), 155061 C, 16 H, 63 S, 512 B
ad8: 16 secs/int, 1 depth queue, UDMA100
pcm0: measured ac97 link rate at 47996 Hz, will use 48000 Hz
ioapic0: routing intpin 1 (ISA IRQ 1) to cluster 0
ioapic0: routing intpin 3 (ISA IRQ 3) to cluster 0
ioapic0: routing intpin 4 (ISA IRQ 4) to cluster 0
ioapic0: routing intpin 6 (ISA IRQ 6) to cluster 0
ioapic0: routing intpin 8 (ISA IRQ 8) to cluster 0
ioapic0: routing intpin 9 (ISA IRQ 9) to cluster 0
ioapic0: routing intpin 12 (ISA IRQ 12) to cluster 0
ioapic0: routing intpin 14 (ISA IRQ 14) to cluster 0
ioapic0: routing intpin 15 (ISA IRQ 15) to cluster 0
ioapic0: routing intpin 17 (PCI IRQ 17) to cluster 0
ioapic0: routing intpin 19 (PCI IRQ 19) to cluster 0
ioapic0: routing intpin 20 (PCI IRQ 20) to cluster 0
ioapic0: routing intpin 21 (PCI IRQ 21) to cluster 0
GEOM: new disk ad0
GEOM: new disk ad8
Trying to mount root from ufs:/dev/ad0a
start_init: trying /sbin/init
ipfw2 initialized, divert loadable, rule-based forwarding disabled, default to deny, logging disabled
WARNING: attempt to net_add_domain(netgraph) after domainfinalize()
em0: Link is up 100 Mbps Full Duplex
--8t9RHnE3ZwKMSgU+
Content-Type: text/plain; charset=us-ascii
Content-Disposition: attachment; filename="dmesg.boot.no_mixed_mode"
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 6.0-CURRENT #3: Fri Mar 25 10:44:58 EET 2005
ru@hammer.runet:/usr/obj/usr/src/sys/HAMMER
WARNING: WITNESS option enabled, expect reduced performance.
Preloaded elf kernel "/boot/kernel/kernel" at 0xffffffff8068b000.
Preloaded elf obj module "/boot/kernel/if_em.ko" at 0xffffffff8068b1d0.
Preloaded elf obj module "/boot/kernel/if_xl.ko" at 0xffffffff8068b6f8.
Preloaded elf obj module "/boot/kernel/miibus.ko" at 0xffffffff8068bc20.
Preloaded elf obj module "/boot/kernel/snd_ich.ko" at 0xffffffff8068c148.
Preloaded elf obj module "/boot/kernel/sound.ko" at 0xffffffff8068c6b0.
ACPI APIC Table: <A M I OEMAPIC >
Calibrating clock(s) ... i8254 clock: 1193169 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 1470007358 Hz
CPU: AMD Opteron(tm) Processor 240 (1470.01-MHz K8-class CPU)
Origin = "AuthenticAMD" Id = 0xf51 Stepping = 1
Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2>
AMD Features=0xe0500800<SYSCALL,NX,MMX+,LM,3DNow+,3DNow>
L1 2MB data TLB: 8 entries, fully associative
L1 2MB instruction TLB: 8 entries, fully associative
L1 4KB data TLB: 32 entries, fully associative
L1 4KB instruction TLB: 32 entries, fully associative
L1 data cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L1 instruction cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L2 2MB unified TLB: 0 entries, disabled/not present
L2 4KB data TLB: 512 entries, 4-way associative
L2 4KB instruction TLB: 512 entries, 4-way associative
L2 unified cache: 1024 kbytes, 64 bytes/line, 1 lines/tag, 16-way associative
real memory = 1073479680 (1023 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009bfff, 634880 bytes (155 pages)
0x0000000000789000 - 0x000000003e189fff, 1033900032 bytes (252417 pages)
avail memory = 1028120576 (980 MB)
APIC: CPU 0 has ACPI ID 1
MADT: Found IO APIC ID 1, Interrupt 0 at 0xfec00000
ioapic0: Routing external 8259A's -> intpin 0
ioapic0: intpin 0 -> ExtINT (edge, high)
ioapic0: intpin 1 -> ISA IRQ 1 (edge, high)
ioapic0: intpin 2 -> ISA IRQ 2 (edge, high)
ioapic0: intpin 3 -> ISA IRQ 3 (edge, high)
ioapic0: intpin 4 -> ISA IRQ 4 (edge, high)
ioapic0: intpin 5 -> ISA IRQ 5 (edge, high)
ioapic0: intpin 6 -> ISA IRQ 6 (edge, high)
ioapic0: intpin 7 -> ISA IRQ 7 (edge, high)
ioapic0: intpin 8 -> ISA IRQ 8 (edge, high)
ioapic0: intpin 9 -> ISA IRQ 9 (edge, high)
ioapic0: intpin 10 -> ISA IRQ 10 (edge, high)
ioapic0: intpin 11 -> ISA IRQ 11 (edge, high)
ioapic0: intpin 12 -> ISA IRQ 12 (edge, high)
ioapic0: intpin 13 -> ISA IRQ 13 (edge, high)
ioapic0: intpin 14 -> ISA IRQ 14 (edge, high)
ioapic0: intpin 15 -> ISA IRQ 15 (edge, high)
ioapic0: intpin 16 -> PCI IRQ 16 (level, low)
ioapic0: intpin 17 -> PCI IRQ 17 (level, low)
ioapic0: intpin 18 -> PCI IRQ 18 (level, low)
ioapic0: intpin 19 -> PCI IRQ 19 (level, low)
ioapic0: intpin 20 -> PCI IRQ 20 (level, low)
ioapic0: intpin 21 -> PCI IRQ 21 (level, low)
ioapic0: intpin 22 -> PCI IRQ 22 (level, low)
ioapic0: intpin 23 -> PCI IRQ 23 (level, low)
MADT: Interrupt override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
ioapic0: intpin 2 trigger: edge
ioapic0: intpin 2 polarity: high
MADT: Interrupt override: source 9, irq 9
ioapic0: intpin 9 trigger: level
ioapic0: intpin 9 polarity: high
MADT: Interrupt override: source 14, irq 14
ioapic0: intpin 14 trigger: edge
ioapic0: intpin 14 polarity: high
MADT: Interrupt override: source 15, irq 15
ioapic0: intpin 15 trigger: edge
ioapic0: intpin 15 polarity: high
ioapic0 <Version 1.1> irqs 0-23 on motherboard
cpu0 BSP:
ID: 0x00000000 VER: 0x00040010 LDR: 0x01000000 DFR: 0x0fffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000100ef therm: 0x00000000 err: 0x0001000f pcm: 0x00010000
random: <entropy source, Software, Yarrow>
io: <I/O>
mem: <memory>
null: <null device, zero device>
acpi0: <A M I OEMXSDT> on motherboard
acpi0: [MPSAFE]
pci_open(1): mode 1 addr port (0x0cf8) is 0x80015004
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=00d110de)
AcpiOsDerivePciId: bus 0 dev 1 func 0
acpi0: Power Button (fixed)
ACPI timer: 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 -> 10
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0
cpu0: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci_link0: <ACPI PCI Link LKSM> irq 0 on acpi0
pci_link0: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 22
pci_link0: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 22
pci_link0: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 22
pci_link1: <ACPI PCI Link LUS0> irq 11 on acpi0
pci_link1: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 11 N 0 20
pci_link1: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 20
pci_link1: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 20
pci_link2: <ACPI PCI Link LAUI> irq 5 on acpi0
pci_link2: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 5 N 0 21
pci_link2: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 21
pci_link2: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 21
pci_link3: <ACPI PCI Link LKMO> irq 0 on acpi0
pci_link3: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 21
pci_link3: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 21
pci_link3: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 21
pci_link4: <ACPI PCI Link LUS1> irq 5 on acpi0
pci_link4: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 5 N 0 20
pci_link4: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 20
pci_link4: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 20
pci_link5: <ACPI PCI Link LUS2> irq 10 on acpi0
pci_link5: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 10 N 0 20
pci_link5: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 20
pci_link5: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 20
pci_link6: <ACPI PCI Link LNKE> irq 11 on acpi0
pci_link6: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 11 N 0 16
pci_link6: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 16
pci_link6: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 16
pci_link7: <ACPI PCI Link LKLN> irq 0 on acpi0
pci_link7: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 21
pci_link7: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 21
pci_link7: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 21
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
map[10]: type 3, range 32, base f0000000, size 27, enabled
found-> vendor=0x10de, dev=0x00d1, revid=0xa4
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x10de, dev=0x00d0, revid=0xf6
bus=0, slot=1, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x000f, statreg=0x00a0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[20]: type 4, range 32, base 00005000, size 6, enabled
map[24]: type 4, range 32, base 00005040, size 6, enabled
found-> vendor=0x10de, dev=0x00d4, revid=0xa4
bus=0, slot=1, func=1
class=0c-05-00, hdrtype=0x00, mfdev=1
cmdreg=0x0001, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
intpin=a, irq=255
powerspec 2 supports D0 D3 current D0
map[10]: type 1, range 32, base febfd000, size 12, enabled
pcib0: matched entry for 0.2.INTA (src \\_SB_.LUS0:0)
pci_link1: Picked IRQ 20 with weight 0
ioapic0: Changing polarity for pin 20 to high
pcib0: slot 2 INTA routed to irq 20 via \\_SB_.LUS0
found-> vendor=0x10de, dev=0x00d7, revid=0xa5
bus=0, slot=2, func=0
class=0c-03-10, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
intpin=a, irq=20
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base febfe000, size 12, enabled
pcib0: matched entry for 0.2.INTB (src \\_SB_.LUS1:0)
pci_link4: Picked IRQ 20 with weight 1
pcib0: slot 2 INTB routed to irq 20 via \\_SB_.LUS1
found-> vendor=0x10de, dev=0x00d7, revid=0xa5
bus=0, slot=2, func=1
class=0c-03-10, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
intpin=b, irq=20
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base febffc00, size 8, enabled
pcib0: matched entry for 0.2.INTC (src \\_SB_.LUS2:0)
pci_link5: Picked IRQ 20 with weight 2
pcib0: slot 2 INTC routed to irq 20 via \\_SB_.LUS2
found-> vendor=0x10de, dev=0x00d8, revid=0xa2
bus=0, slot=2, func=2
class=0c-03-20, hdrtype=0x00, mfdev=1
cmdreg=0x0006, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
intpin=c, irq=20
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 0000e800, size 8, enabled
map[14]: type 4, range 32, base 0000ec00, size 7, enabled
map[18]: type 1, range 32, base febfb000, size 12, enabled
pcib0: matched entry for 0.6.INTA (src \\_SB_.LAUI:0)
pci_link2: Picked IRQ 21 with weight 0
ioapic0: Changing polarity for pin 21 to high
pcib0: slot 6 INTA routed to irq 21 via \\_SB_.LAUI
found-> vendor=0x10de, dev=0x00da, revid=0xa2
bus=0, slot=6, func=0
class=04-01-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x05 (1250 ns)
intpin=a, irq=21
powerspec 2 supports D0 D1 D2 D3 current D0
map[20]: type 4, range 32, base 0000ffa0, size 4, enabled
found-> vendor=0x10de, dev=0x00d5, revid=0xa5
bus=0, slot=8, func=0
class=01-01-8a, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
powerspec 2 supports D0 D3 current D0
found-> vendor=0x10de, dev=0x00dd, revid=0xa2
bus=0, slot=10, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x00a0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns)
found-> vendor=0x10de, dev=0x00d2, revid=0xa4
bus=0, slot=11, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x0220, cachelnsz=0 (dwords)
lattimer=0x10 (480 ns), mingnt=0x0b (2750 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x1100, revid=0x00
bus=0, slot=24, func=0
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x1101, revid=0x00
bus=0, slot=24, func=1
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x1102, revid=0x00
bus=0, slot=24, func=2
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x1103, revid=0x00
bus=0, slot=24, func=3
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
isab0: <PCI-ISA bridge> at device 1.0 on pci0
isa0: <ISA bus> on isab0
pci0: <serial bus, SMBus> at device 1.1 (no driver attached)
pci0:1:1: Transition from D0 to D3
ohci0: <nVidia nForce3 USB Controller> mem 0xfebfd000-0xfebfdfff irq 20 at device 2.0 on pci0
ohci0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfebfd000
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <nVidia nForce3 USB Controller> on ohci0
usb0: USB revision 1.0
uhub0: nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
ohci1: <nVidia nForce3 USB Controller> mem 0xfebfe000-0xfebfefff irq 20 at device 2.1 on pci0
ohci1: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfebfe000
ohci1: [GIANT-LOCKED]
usb1: OHCI version 1.0, legacy support
usb1: SMM does not respond, resetting
usb1: <nVidia nForce3 USB Controller> on ohci1
usb1: USB revision 1.0
uhub1: nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 3 ports with 3 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfebffc00-0xfebffcff irq 20 at device 2.2 on pci0
ehci0: Reserved 0x100 bytes for rid 0x10 type 3 at 0xfebffc00
ehci0: [GIANT-LOCKED]
usb2: waiting for BIOS to give up control
usb2: timed out waiting for BIOS
usb2: EHCI version 1.0
usb2: companion controllers, 4 ports each: usb0 usb1
usb2: <EHCI (generic) USB 2.0 controller> on ehci0
usb2: USB revision 2.0
uhub2: nVidia EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 6 ports with 6 removable, self powered
pcm0: <nVidia nForce3> port 0xe800-0xe8ff,0xec00-0xec7f mem 0xfebfb000-0xfebfbfff irq 21 at device 6.0 on pci0
pcm0: Reserved 0x100 bytes for rid 0x10 type 4 at 0xe800
pcm0: Reserved 0x80 bytes for rid 0x14 type 4 at 0xec00
pcm0: [GIANT-LOCKED]
pcm0: <Avance Logic ALC650 AC97 Codec (id = 0x414c4720)>
pcm0: Codec features 20 bit DAC, 18 bit ADC, 5 bit master volume, Realtek 3D Stereo Enhancement
pcm0: Primary codec extended features variable rate PCM, double rate PCM, reserved 1, center DAC, surround DAC, LFE DAC, reserved 4
pcm0: sndbuf_setmap 3db86000, 4000; 0xffffffffa5446000 -> 3db86000
pcm0: sndbuf_setmap 3db78000, 4000; 0xffffffffa544a000 -> 3db78000
atapci0: <nVidia nForce3 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 8.0 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xffa0
ata0: channel #0 on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0-master: stat=0x90 err=0x90 lsb=0x90 msb=0x90
ata0-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata0-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata0: [MPSAFE]
ata1: channel #1 on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=03 ostat0=7f ostat1=50
ata1-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-slave: stat=0x10 err=0x01 lsb=0x14 msb=0xeb
ata1: reset tp2 stat0=ff stat1=10 devices=0x8<ATAPI_SLAVE>
ata1: [MPSAFE]
pcib1: <ACPI PCI-PCI bridge> at device 10.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xc000-0xdfff
pcib1: memory decode 0xfc800000-0xfc9fffff
pcib1: prefetched decode 0xfff00000-0xfffff
pci_link8: <ACPI PCI Link LNKA> irq 11 on acpi0
pci_link8: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 11 N 0 17
pci_link8: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 17
pci_link8: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 17
pci_link9: <ACPI PCI Link LNKB> irq 0 on acpi0
pci_link9: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 18
pci_link9: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 18
pci_link9: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 18
pci_link10: <ACPI PCI Link LNKC> irq 10 on acpi0
pci_link10: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 10 N 0 19
pci_link10: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 19
pci_link10: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 19
pci_link11: <ACPI PCI Link LNKD> irq 0 on acpi0
pci_link11: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 17
pci_link11: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 17
pci_link11: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 17
ACPI: Found matching pin for 0.6.INTA at func 0: 21
pci_link11: BIOS IRQ 21 for 0.6.INTA is invalid
pci1: <ACPI PCI bus> on pcib1
pci1: physical bus=1
map[10]: type 4, range 32, base 0000dc00, size 7, enabled
pcib1: (null) requested I/O range 0xdc00-0xdc7f: in range
map[14]: type 1, range 32, base fc9ffc00, size 7, enabled
pcib1: (null) requested memory range 0xfc9ffc00-0xfc9ffc7f: good
pcib1: matched entry for 1.5.INTA (src \\_SB_.LNKC:0)
pci_link10: Picked IRQ 19 with weight 0
ioapic0: Changing polarity for pin 19 to high
pcib1: slot 5 INTA routed to irq 19 via \\_SB_.LNKC
found-> vendor=0x10b7, dev=0x9200, revid=0x74
bus=1, slot=5, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0117, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x0a (2500 ns), maxlat=0x0a (2500 ns)
intpin=a, irq=19
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base fc9a0000, size 17, enabled
pcib1: (null) requested memory range 0xfc9a0000-0xfc9bffff: good
map[14]: type 1, range 32, base fc980000, size 17, enabled
pcib1: (null) requested memory range 0xfc980000-0xfc99ffff: good
map[18]: type 4, range 32, base 0000d800, size 6, enabled
pcib1: (null) requested I/O range 0xd800-0xd83f: in range
pcib1: matched entry for 1.7.INTA (src \\_SB_.LNKA:0)
pci_link8: Picked IRQ 17 with weight 0
ioapic0: Changing polarity for pin 17 to high
pcib1: slot 7 INTA routed to irq 17 via \\_SB_.LNKA
found-> vendor=0x8086, dev=0x1076, revid=0x00
bus=1, slot=7, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0117, statreg=0x0230, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0xff (63750 ns), maxlat=0x00 (0 ns)
intpin=a, irq=17
powerspec 2 supports D0 D3 current D0
MSI supports 1 message, 64 bit
map[10]: type 4, range 32, base 0000d400, size 6, enabled
pcib1: (null) requested I/O range 0xd400-0xd43f: in range
map[14]: type 4, range 32, base 0000d000, size 4, enabled
pcib1: (null) requested I/O range 0xd000-0xd00f: in range
map[18]: type 4, range 32, base 0000cc00, size 7, enabled
pcib1: (null) requested I/O range 0xcc00-0xcc7f: in range
map[1c]: type 1, range 32, base fc9fe000, size 12, enabled
pcib1: (null) requested memory range 0xfc9fe000-0xfc9fefff: good
map[20]: type 1, range 32, base fc940000, size 17, enabled
pcib1: (null) requested memory range 0xfc940000-0xfc95ffff: good
pcib1: matched entry for 1.8.INTA (src \\_SB_.LNKC:0)
pcib1: slot 8 INTA routed to irq 19 via \\_SB_.LNKC
found-> vendor=0x105a, dev=0x3373, revid=0x02
bus=1, slot=8, func=0
class=01-04-00, hdrtype=0x00, mfdev=0
cmdreg=0x0117, statreg=0x0230, cachelnsz=145 (dwords)
lattimer=0x60 (2880 ns), mingnt=0x04 (1000 ns), maxlat=0x12 (4500 ns)
intpin=a, irq=19
powerspec 2 supports D0 D1 D3 current D0
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xdc00-0xdc7f mem 0xfc9ffc00-0xfc9ffc7f irq 19 at device 5.0 on pci1
xl0: Reserved 0x80 bytes for rid 0x14 type 3 at 0xfc9ffc00
xl0: using memory mapped I/O
xl0: media options word: a
xl0: found MII/AUTO
miibus0: <MII bus> on xl0
xlphy0: <3c905C 10/100 internal PHY> on miibus0
xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl0: bpf attached
xl0: Ethernet address: 00:50:da:42:6e:8e
xl0: [MPSAFE]
em0: <Intel(R) PRO/1000 Network Connection, Version - 1.7.35> port 0xd800-0xd83f mem 0xfc9a0000-0xfc9bffff,0xfc980000-0xfc99ffff irq 17 at device 7.0 on pci1
em0: Reserved 0x20000 bytes for rid 0x10 type 3 at 0xfc9a0000
em0: Reserved 0x40 bytes for rid 0x18 type 4 at 0xd800
em0: [MPSAFE]
em0: bpf attached
em0: Ethernet address: 00:0e:0c:37:c2:82
em0: Speed:N/A Duplex:N/A
atapci1: <Promise PDC20378 SATA150 controller> port 0xd400-0xd43f,0xd000-0xd00f,0xcc00-0xcc7f mem 0xfc9fe000-0xfc9fefff,0xfc940000-0xfc95ffff irq 19 at device 8.0 on pci1
atapci1: failed: rid 0x20 is memory, requested 4
atapci1: Reserved 0x20000 bytes for rid 0x20 type 3 at 0xfc940000
atapci1: Reserved 0x1000 bytes for rid 0x1c type 3 at 0xfc9fe000
atapci1: [MPSAFE]
ata2: channel #0 on atapci1
ata2: reset tp1 mask=01 ostat0=7f ostat1=7f
ata2-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata2-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata2-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata2-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata2-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata2-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata2-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata2: reset tp2 stat0=ff stat1=00 devices=0x0
ata2: [MPSAFE]
ata3: channel #1 on atapci1
ata3: reset tp1 mask=01 ostat0=7f ostat1=7f
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3: reset tp2 stat0=ff stat1=00 devices=0x0
ata3: [MPSAFE]
ata4: channel #2 on atapci1
ata4: reset tp1 mask=03 ostat0=50 ostat1=00
ata4-master: stat=0x90 err=0x90 lsb=0x90 msb=0x90
ata4-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata4-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00
ata4: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata4: [MPSAFE]
pcib2: <ACPI PCI-PCI bridge> at device 11.0 on pci0
pcib2: secondary bus 2
pcib2: subordinate bus 2
pcib2: I/O decode 0xf000-0xfff
pcib2: memory decode 0xfca00000-0xfeafffff
pcib2: prefetched decode 0xe4700000-0xec6fffff
pcib2: could not get PCI interrupt routing table for \\_SB_.PCI0.P0P2 - AE_NOT_FOUND
pci2: <ACPI PCI bus> on pcib2
pci2: physical bus=2
map[10]: type 1, range 32, base fd000000, size 24, enabled
pcib2: (null) requested memory range 0xfd000000-0xfdffffff: good
map[14]: type 3, range 32, base e8000000, size 26, enabled
pcib2: (null) requested memory range 0xe8000000-0xebffffff: good
pcib0: matched entry for 0.11.INTA (src \\_SB_.LNKE:0)
pci_link6: Picked IRQ 16 with weight 0
ioapic0: Changing polarity for pin 16 to high
pcib0: slot 11 INTA routed to irq 16 via \\_SB_.LNKE
pcib2: slot 0 INTA is routed to irq 16
found-> vendor=0x10de, dev=0x0181, revid=0xc1
bus=2, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x02b0, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x05 (1250 ns), maxlat=0x01 (250 ns)
intpin=a, irq=16
powerspec 2 supports D0 D3 current D0
pci2: <display, VGA> at device 0.0 (no driver attached)
acpi_button0: <Power Button> on acpi0
pci_link12: <ACPI PCI Link LTID> irq 0 on acpi0
pci_link12: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 22
pci_link12: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 22
pci_link12: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 22
pci_link13: <ACPI PCI Link LATA> irq 14 on acpi0
pci_link13: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 14 N 0 22
pci_link13: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 22
pci_link13: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 22
fdc0: <floppy drive controller (FDE)> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: ic_type 90 part_id 80
fdc0: [MPSAFE]
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
atkbd0: [GIANT-LOCKED]
psm0: unable to allocate IRQ
psmcpnp0: <PS/2 mouse port> irq 12 on acpi0
psm0: current command byte:0065
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model IntelliMouse, device ID 3-00, 3 buttons
psm0: config:00000000, flags:00000008, packet size:4
psm0: syncmask:08, syncbits:00
sio0: irq maps: 0xc21 0xc31 0xc21 0xc21
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
sio1: irq maps: 0xc21 0xc29 0xc21 0xc21
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
atkbdc: atkbdc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
sc: sc0 already exists; skipping it
sio: sio0 already exists; skipping it
sio: sio1 already exists; skipping it
vga: vga0 already exists; skipping it
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <ISA Option ROMs> at iomem 0xc0000-0xcf7ff,0xcf800-0xcffff,0xd0000-0xd0fff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
ppc0 failed to probe at irq 7 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
isa_probe_children: probing PnP devices
Device configuration finished.
Timecounter "TSC" frequency 1470007358 Hz quality 800
Timecounters tick every 1.000 msec
Linux ELF exec handler installed
lo0: bpf attached
ata0-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
ata0-master: setting PIO4 on nVidia nForce3 chip
ata0-master: setting UDMA100 on nVidia nForce3 chip
ad0: <ST380011A/3.04> ATA-6 disk at ata0-master
ad0: 76319MB (156301488 sectors), 155061 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA100
ata1-slave: pio=0x0c wdma=0x22 udma=0x44 cable=40pin
ata1-slave: setting PIO4 on nVidia nForce3 chip
ata1-slave: DMA limited to UDMA33, non-ATA66 cable or device
ata1-slave: setting UDMA33 on nVidia nForce3 chip
acd0: <COM4824/VER 1.01> CDRW drive at ata1 as slave
acd0: read 345KB/s (8251KB/s) write 8251KB/s (8251KB/s), 2048KB buffer, UDMA33
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, packet
acd0: Writes: CDR, CDRW, test write, burnproof
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
ata4-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
ad8: <ST380011A/3.04> ATA-6 disk at ata4-master
ad8: 76319MB (156301488 sectors), 155061 C, 16 H, 63 S, 512 B
ad8: 16 secs/int, 1 depth queue, UDMA100
pcm0: measured ac97 link rate at 17112 Hz
ioapic0: routing intpin 1 (ISA IRQ 1) to cluster 0
ioapic0: routing intpin 2 (ISA IRQ 0) to cluster 0
ioapic0: routing intpin 3 (ISA IRQ 3) to cluster 0
ioapic0: routing intpin 4 (ISA IRQ 4) to cluster 0
ioapic0: routing intpin 6 (ISA IRQ 6) to cluster 0
ioapic0: routing intpin 8 (ISA IRQ 8) to cluster 0
ioapic0: routing intpin 9 (ISA IRQ 9) to cluster 0
ioapic0: routing intpin 12 (ISA IRQ 12) to cluster 0
ioapic0: routing intpin 14 (ISA IRQ 14) to cluster 0
ioapic0: routing intpin 15 (ISA IRQ 15) to cluster 0
ioapic0: routing intpin 17 (PCI IRQ 17) to cluster 0
ioapic0: routing intpin 19 (PCI IRQ 19) to cluster 0
ioapic0: routing intpin 20 (PCI IRQ 20) to cluster 0
ioapic0: routing intpin 21 (PCI IRQ 21) to cluster 0
--8t9RHnE3ZwKMSgU+--
--yNb1oOkm5a9FJOVX
Content-Type: application/pgp-signature
Content-Disposition: inline
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.0 (FreeBSD)
iD8DBQFCQ93qqRfpzJluFF4RArvZAJ0XF3nk3ix1SJMe4BolZ8AdvC/KIgCeJpgY
VIvb/+emJM0ihcBsLuFOLKM=
=P3eJ
-----END PGP SIGNATURE-----
--yNb1oOkm5a9FJOVX--
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20050325094618.GA76747>