Date: Wed, 8 Nov 2000 09:12:36 -0800 From: Paul Saab <paul@mu.org> To: Nick Barnes <Nick.Barnes@pobox.com> Cc: freebsd-multimedia@freebsd.org, freebsd-hardware@freebsd.org Subject: Re: Intel D815EEA motherboard sound and network Message-ID: <20001108091236.A41632@elvis.mu.org> In-Reply-To: <4453.973699030@raven.ravenbrook.com>; from Nick.Barnes@pobox.com on Wed, Nov 08, 2000 at 03:57:10PM %2B0000 References: <4453.973699030@raven.ravenbrook.com>
next in thread | previous in thread | raw e-mail | index | archive | help
You need to run 4-stable or wait for 4.2-RELEASE to come out to support the onboard ethernet on the Intel 815 board. I am going to try and get Cameron an 815 board so he can do the sound support, but that is taking a bit of time to get the hardware for him. Nick Barnes (Nick.Barnes@pobox.com) wrote: > I have a new PC with an Intel D815EEA motherboard. This comes with > onboard sound, network, and display. I have a Matrox graphics card so > I don't care about the onboard display. > > The motherboard doc claims that the network is compatible with Intel > Pro 100, so I expected it to show up as fxp0; it didn't. Archives of > freebsd-hardware suggest this is known and unlikely to be fixed. Oh > well. I've put a RealTek NIC in instead. > > The motherboard doc also claims that the sound is compatible with > SoundBlaster PCI 128. I've never used sound under FreeBSD, so I'm a > bit of a novice here. Can someone advise me what I need in my kernel > config to drive this? I've tried a couple of things (pcm, snd) with > no visible effect on the dmesg. > > Here's a verbose boot with GENERIC. Note also the "Bad PnP BIOS data > checksum" message. > > Copyright (c) 1992-2000 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD 4.1-RELEASE #0: Fri Jul 28 14:30:31 GMT 2000 > jkh@ref4.freebsd.org:/usr/src/sys/compile/GENERIC > Calibrating clock(s) ... TSC clock: 797557265 Hz, i8254 clock: 1193154 Hz > CLK_USE_I8254_CALIBRATION not specified - using default frequency > Timecounter "i8254" frequency 1193182 Hz > CLK_USE_TSC_CALIBRATION not specified - using old calibration method > CPU: Pentium III/Pentium III Xeon/Celeron (797.58-MHz 686-class CPU) > Origin = "GenuineIntel" Id = 0x686 Stepping = 6 > Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,XMM> > real memory = 268173312 (261888K bytes) > Physical memory chunk(s): > 0x00001000 - 0x0009efff, 647168 bytes (158 pages) > 0x00426000 - 0x0ffb7fff, 263790592 bytes (64402 pages) > avail memory = 256700416 (250684K bytes) > bios32: Found BIOS32 Service Directory header at 0xc00fda60 > bios32: Entry = 0xfda74 (c00fda74) Rev = 0 Len = 1 > pcibios: PCI BIOS entry at 0xda95 > pnpbios: Bad PnP BIOS data checksum > Other BIOS signatures found: > ACPI: 000ff980 > Preloaded elf kernel "kernel.GENERIC" at 0xc040d000. > Pentium Pro MTRR support enabled > md0: Malloc disk > Creating DISK md0 > Math emulator present > pci_open(1): mode 1 addr port (0x0cf8) is 0x8000005c > pci_open(1a): mode1res=0x80000000 (0x80000000) > pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=11308086) > npx0: <math processor> on motherboard > npx0: INT 16 interface > pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000 > pci_open(1a): mode1res=0x80000000 (0x80000000) > pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=11308086) > pcib0: <Host to PCI bridge> on motherboard > found-> vendor=0x8086, dev=0x1130, revid=0x02 > class=06-00-00, hdrtype=0x00, mfdev=0 > subordinatebus=0 secondarybus=0 > map[10]: type 1, range 32, base f8000000, size 26 > found-> vendor=0x8086, dev=0x1131, revid=0x02 > class=06-04-00, hdrtype=0x01, mfdev=0 > subordinatebus=2 secondarybus=2 > found-> vendor=0x8086, dev=0x244e, revid=0x01 > class=06-04-00, hdrtype=0x01, mfdev=0 > subordinatebus=1 secondarybus=1 > found-> vendor=0x8086, dev=0x2440, revid=0x01 > class=06-01-00, hdrtype=0x00, mfdev=1 > subordinatebus=0 secondarybus=0 > found-> vendor=0x8086, dev=0x244b, revid=0x01 > class=01-01-80, hdrtype=0x00, mfdev=0 > subordinatebus=0 secondarybus=0 > map[20]: type 1, range 32, base 0000ffa0, size 4 > found-> vendor=0x8086, dev=0x2442, revid=0x01 > class=0c-03-00, hdrtype=0x00, mfdev=0 > subordinatebus=0 secondarybus=0 > intpin=d, irq=11 > map[20]: type 1, range 32, base 0000ef40, size 5 > found-> vendor=0x8086, dev=0x2443, revid=0x01 > class=0c-05-00, hdrtype=0x00, mfdev=0 > subordinatebus=0 secondarybus=0 > intpin=b, irq=9 > map[20]: type 1, range 32, base 0000efa0, size 4 > found-> vendor=0x8086, dev=0x2444, revid=0x01 > class=0c-03-00, hdrtype=0x00, mfdev=0 > subordinatebus=0 secondarybus=0 > intpin=c, irq=10 > map[20]: type 1, range 32, base 0000ef80, size 5 > found-> vendor=0x8086, dev=0x2445, revid=0x01 > class=04-01-00, hdrtype=0x00, mfdev=0 > subordinatebus=0 secondarybus=0 > intpin=b, irq=9 > map[10]: type 1, range 32, base 0000e800, size 8 > map[14]: type 1, range 32, base 0000ef00, size 6 > pci0: <PCI bus> on pcib0 > pcib1: <PCI to PCI bridge (vendor=8086 device=1131)> at device 1.0 on pci0 > found-> vendor=0x102b, dev=0x0525, revid=0x04 > class=03-00-00, hdrtype=0x00, mfdev=0 > subordinatebus=0 secondarybus=0 > intpin=a, irq=11 > map[10]: type 1, range 32, base f2000000, size 25 > map[14]: type 1, range 32, base feafc000, size 14 > map[18]: type 1, range 32, base fe000000, size 23 > pci2: <PCI bus> on pcib1 > pci2: <Matrox MGA G400 AGP graphics accelerator> (vendor=0x102b, dev=0x0525) at 0.0 irq 11 > pcib2: <PCI to PCI bridge (vendor=8086 device=244e)> at device 30.0 on pci0 > found-> vendor=0x8086, dev=0x2449, revid=0x01 > class=02-00-00, hdrtype=0x00, mfdev=0 > subordinatebus=0 secondarybus=0 > intpin=a, irq=11 > map[10]: type 1, range 32, base fd9fe000, size 12 > map[14]: type 1, range 32, base 0000df00, size 6 > found-> vendor=0x10ec, dev=0x8139, revid=0x10 > class=02-00-00, hdrtype=0x00, mfdev=0 > subordinatebus=0 secondarybus=0 > intpin=a, irq=11 > map[10]: type 1, range 32, base 0000d800, size 8 > map[14]: type 1, range 32, base fd9ffc00, size 8 > pci1: <PCI bus> on pcib2 > pci1: <unknown card> (vendor=0x8086, dev=0x2449) at 8.0 irq 11 > rl0: <RealTek 8139 10/100BaseTX> port 0xd800-0xd8ff mem 0xfd9ffc00-0xfd9ffcff irq 11 at device 13.0 on pci1 > rl0: Ethernet address: 00:50:fc:01:f4:0e > miibus0: <MII bus> on rl0 > rlphy0: <RealTek internal media interface> on miibus0 > rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > bpf: rl0 attached > isab0: <PCI to ISA bridge (vendor=8086 device=2440)> at device 31.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <Generic PCI ATA controller> port 0xffa0-0xffaf at device 31.1 on pci0 > ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0xffa0 > ata0: mask=03 status0=50 status1=00 > ata0: mask=03 status0=50 status1=00 > ata0: devices = 0x1 > ata0: at 0x1f0 irq 14 on atapci0 > ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0xffa8 > ata1: mask=03 status0=50 status1=00 > ata1: mask=03 status0=10 status1=00 > ata1: devices = 0x4 > ata1: at 0x170 irq 15 on atapci0 > uhci0: <UHCI (generic) USB controller> port 0xef40-0xef5f irq 11 at device 31.2 on pci0 > uhci0: (New UHCI DeviceId=0x24428086) > using shared irq11. > usb0: <UHCI (generic) USB controller> on uhci0 > usb0: USB revision 1.0 > uhub0: (0x24428086) UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 2 ports with 2 removable, self powered > uhub0: port 1 power on failed, IOERROR > uhub0: port 2 power on failed, IOERROR > pci0: <unknown card> (vendor=0x8086, dev=0x2443) at 31.3 irq 9 > uhci1: <UHCI (generic) USB controller> port 0xef80-0xef9f irq 10 at device 31.4 on pci0 > uhci1: (New UHCI DeviceId=0x24448086) > usb1: <UHCI (generic) USB controller> on uhci1 > usb1: USB revision 1.0 > uhub1: (0x24448086) UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub1: 2 ports with 2 removable, self powered > uhub1: port 1 power on failed, IOERROR > uhub1: port 2 power on failed, IOERROR > pci0: <unknown card> (vendor=0x8086, dev=0x2445) at 31.5 irq 9 > Trying Read_Port at 203 > Trying Read_Port at 243 > Trying Read_Port at 283 > Trying Read_Port at 2c3 > Trying Read_Port at 303 > Trying Read_Port at 343 > Trying Read_Port at 383 > Trying Read_Port at 3c3 > ata-: ata0 exists, using next available unit number > ata-: ata1 exists, using next available unit number > isa_probe_children: disabling PnP devices > isa_probe_children: probing non-PnP devices > fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 > fdc0: FIFO enabled, 8 bytes threshold > fd0: <1440-KB 3.5" drive> on fdc0 drive 0 > bt0: Failed Status Reg Test - fe > bt_isa_probe: Probe failed at 0x330 > bt0: Failed Status Reg Test - ff > bt_isa_probe: Probe failed at 0x334 > bt0: Failed Status Reg Test - ff > bt_isa_probe: Probe failed at 0x230 > bt0: Failed Status Reg Test - ff > bt_isa_probe: Probe failed at 0x234 > bt0: Failed Status Reg Test - ff > bt_isa_probe: Probe failed at 0x130 > bt0: Failed Status Reg Test - ff > bt_isa_probe: Probe failed at 0x134 > aha0: status reg test failed fe > aha0: status reg test failed ff > ated 4 times > atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 > atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 > atkbd: the current kbd controller command byte 0065 > atkbd: keyboard ID 0x41ab (2) > kbdc: RESET_KBD return code:00fa > kbdc: RESET_KBD status:00aa > kbd0 at atkbd0 > kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000 > psm0: current command byte:0065 > kbdc: TEST_AUX_PORT status:0000 > kbdc: RESET_AUX return code:00fa > kbdc: RESET_AUX status:00aa > kbdc: RESET_AUX ID:0000 > psm: status 00 02 64 > psm: status 00 00 64 > psm: status 00 03 64 > psm: status 00 03 64 > psm: data 08 06 05 > psm: data 08 01 00 > psm: status 00 02 64 > psm0: <PS/2 Mouse> irq 12 on atkbdc0 > psm0: model IntelliMouse, device ID 3-00, 3 buttons > psm0: config:00000000, flags:00000000, packet size:4 > psm0: syncmask:08, syncbits:08 > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > fb0: vga0, vga, type:VGA (5), flags:0x7007f > fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000 > fb0: init mode:24, bios mode:3, current mode:24 > fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k > VGA parameters upon power-up > 50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81 > bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96 > b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c > 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff > VGA parameters in BIOS for mode 24 > 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 > bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 > b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c > 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff > EGA/VGA parameters to be used for mode 24 > 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 > bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 > b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c > 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > sc0: fb0, kbd0, terminal emulator: sc (syscons terminal) > pcic1: not probed (disabled) > sio0: irq maps: 0x41 0x51 0x41 0x41 > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > sio0: type 16550A > sio1: irq maps: 0x41 0x49 0x41 0x41 > sio1 at port 0x2f8-0x2ff irq 3 on isa0 > sio1: type 16550A > sio2: not probed (disabled) > sio3: not probed (disabled) > ppc0: parallel port found at 0x378 > ppc0: using extended I/O port range > ppc0: ECP SPP ECP+EPP SPP > ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 > ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode > ppc0: FIFO with 16/16/8 bytes threshold > ppi0: <Parallel I/O> on ppbus0 > lpt0: <Printer> on ppbus0 > lpt0: Interrupt-driven port > plip0: <PLIP network interface> on ppbus0 > bpf: lp0 attached > isa_probe_children: probing PnP devices > BIOS Geometries: > 0:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors > 0 accounted for > Device configuration finished. > bpf: sl0 attached > bpf: ppp0 attached > new masks: bio 68cc40, tty 63109a, net 67189a > bpf: lo0 attached > bpf: gif0 attached > bpf: gif1 attached > bpf: gif2 attached > bpf: gif3 attached > bpf: faith0 attached > ad0: <IBM-DTLA-307045/TX6OA60A> ATA-5 disk at ata0 as master > ad0: 43979MB (90069840 sectors), 89355 cyls, 16 heads, 63 S/T, 512 B/S > ad0: 16 secs/int, 32 depth queue, BIOSDMA > ad0: piomode=4 dmamode=2 udmamode=4 cblid=1 > Creating DISK ad0 > Creating DISK wd0 > ata1-master: piomode=4 dmamode=2 udmamode=-1 dmaflag=1 > ata1-master: success setting up PIO4 mode on generic chip > acd0: <SAMSUNG CD-ROM SC-152C/CS02> CDROM drive at ata1 as master > acd0: read 171KB/s (8937KB/s), 128KB buffer, PIO4 > acd0: Reads: CD-R, CD-RW, CD-DA stream, packet > acd0: Audio: play, 255 volume levels > acd0: Mechanism: ejectable tray > acd0: Medium: no/blank disc inside, unlocked > Mounting root from ufs:/dev/ad0s1a > ad0s1: type 0xa5, start 63, end = 41929649, size 41929587 : OK > start_init: trying /sbin/init > > > -- > FreeBSD 2.2.8-RELEASE: up 6 days, 5:09 > last reboot Thu Nov 2 10:55 (lightning strike) > > > To Unsubscribe: send mail to majordomo@FreeBSD.org > with "unsubscribe freebsd-hardware" in the body of the message -- Paul Saab Technical Yahoo paul@mu.org - ps@yahoo-inc.com - ps@freebsd.org Do You .. uhh .. Yahoo!? To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-hardware" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20001108091236.A41632>