Date: Sun, 12 Mar 2017 13:49:14 -0400 From: Outback Dingo <outbackdingo@gmail.com> To: freebsd-arm@freebsd.org Subject: Debugging ESR - Any Ideas? Message-ID: <CAKYr3zynVfS2gM2TNqTJ5M=O-P=ggzQAHEvaBTH%2Bgmk%2BHBgi1A@mail.gmail.com>
next in thread | raw e-mail | index | archive | help
Okay list, any further ideas to debug this?
U-Boot 2016.09.01-00012-g1c00e8f-dirty (Mar 01 2017 - 13:40:10 -0500)
SoC: LS1043AE (0x87920010)
Clock Configuration:
CPU0(A53):1400 MHz CPU1(A53):1400 MHz CPU2(A53):1400 MHz
CPU3(A53):1400 MHz
Bus: 400 MHz DDR: 1600 MT/s FMAN: 466.667 MHz
Reset Configuration Word (RCW):
00000000: 0810000e 0c000000 00000000 00000000
00000010: 45550002 00004002 e0025000 61002000
00000020: 00000000 00000000 00000000 00020f78
>> FreeBSD EFI boot block
Loader path: /boot/loader.efi
Initializing modules: ZFS UFS
Probing 4 block devices.....*. done
ZFS found no pools
UFS found 1 partition
Consoles: EFI console
MMC: block number 0x72c001 exceeds max(0x72c000)
efipart_readwrite: rw=1, status=9223372036854775815
MMC: block number 0x72c001 exceeds max(0x72c000)
efipart_readwrite: rw=1, status=9223372036854775815
Command line arguments: loader.efi
Image base: 0xfcc58000
EFI version: 2.05
EFI Firmware: Das U-boot (rev 0.00)
FreeBSD/arm64 EFI loader, Revision 1.1
(Tue Feb 28 09:17:19 EST 2017 root@FISORLBSD01)
EFI boot environment
Loading /boot/defaults/loader.conf
/boot/kernel/kernel data=0x826f08+0x43b040 syms=[0x8+0x105a20+0x8+0xbed65]
/
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...
Using DTB provided by EFI at 0x88000000.
"Synchronous Abort" handler, esr 0x86000004
ELR: ffff000000001030
LR: f4c01028
00000000f4c05000: f4c04003
00000000f4c05fd0: f4c08003
00000000f4c05fd8: f4c09003
00000000f4c05fe0: f4c0a003
00000000f4c05fe8: f4c0b003
x0 : ffff000000e2a000 x1 : 0000000004c5d91d
x2 : 000000000405d11d x3 : 00000000030802e2
x4 : 00000000fffbc240 x5 : 00000000f4c01024
x6 : 00000000f4c07000 x7 : 0000000000000001
x8 : 00000000f4c06000 x9 : 00000000000f4c07
x10: 0000000000000000 x11: 0000000000000001
x12: 0000000000000003 x13: 00000000f4c06003
x14: 0000000000000398 x15: ffff000000001030
x16: 0000000000000000 x17: 0000000000000000
x18: 0000000000000000 x19: 00000000f4c00000
x20: 00000000f4c01000 x21: 0000000000000000
x22: 000000000000000d x23: 000000000000000e
x24: 00000000f4c05000 x25: 00000000fcc3e29b
x26: 00000000f4c04000 x27: 00000000f4c07000
x28: 00000000f4c00000 x29: 00010000f4c00000
Resetting CPU ...
resetting ...
U-Boot 2016.09.01-00012-g1c00e8f-dirty (Mar 01 2017 - 13:40:10 -0500)
SoC: LS1043AE (0x87920010)
Clock Configuration:
CPU0(A53):1400 MHz CPU1(A53):1400 MHz CPU2(A53):1400 MHz
CPU3(A53):1400 MHz
Bus: 400 MHz DDR: 1600 MT/s FMAN: 466.667 MHz
Reset Configuration Word (RCW):
00000000: 0810000e 0c000000 00000000 00000000
00000010: 45550002 00004002 e0025000 61002000
00000020: 00000000 00000000 00000000 00020f78
00000030: 00000000 04003102 00000096 00000001
Model: LS1043A FRD Board
Board: LS1043AFRD, boot from NOR
SERDES Reference Clocks:
SD1_CLK1 = 100.00MHZ, SD1_CLK2 = 100.00MHZ
I2C: ready
DRAM: 8 GiB (DDR4, 32-bit, CL=11, ECC off)
DDR Chip-Select Interleaving Mode: CS0+CS1
SEC0: RNG instantiated
Waking secondary cores to start from fff15000
All (4) cores are up.
Using SERDES1 Protocol: 17749 (0x4555)
Flash: 128 MiB
NAND: 0 MiB
MMC: FSL_SDHC: 0
PCIe1: Root Complex x1 gen1, regs @ 0x3400000
PCI:
01:00.0 - 126f:0750 - Display controller
PCIe1: Bus 00 - 01
PCIe2: Root Complex no link, regs @ 0x3500000
PCIe3: Root Complex x1 gen1, regs @ 0x3600000
PCI:
03:00.0 - 168c:003c - Network controller
PCIe3: Bus 02 - 03
In: serial
Out: serial
Err: serial
Net: Fman1: Uploading microcode version 108.4.5
FM1@DTSEC1, FM1@DTSEC2, FM1@DTSEC3 [PRIME], FM1@DTSEC5, FM1@DTSEC6
Hit any key to stop autoboot: 0
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?CAKYr3zynVfS2gM2TNqTJ5M=O-P=ggzQAHEvaBTH%2Bgmk%2BHBgi1A>