Date: Thu, 29 Jan 2009 17:34:53 +0300 From: Mike Barnard <mike.barnardq@gmail.com> To: freebsd-stable@freebsd.org Subject: Unable to boot after upgrade to 7.0 or 7.1 STABLE Message-ID: <7dc029620901290634q7ca5361ct496fc2c4a6bfe53f@mail.gmail.com>
next in thread | raw e-mail | index | archive | help
Hi All,
I have run into a problem that seem rather puzzling. I have upgraded an
installation of FreeBSD from 7.0-RELEASE to 7.0-STABLE and 7.1-STABLE, but i
fail to boot with either one of the STABLE upgrades. I end up at this point:
Trying to mount root from ufs:/dev/ad0s1a
Manual root filesystem specification:
<fstype>:<device> Mount <device> using filesystem <fstype>
eg. ufs:da0s1a
? List valid disk boot devices
<empty line> Abort manual input
When i type ?, i get nothing. When i try to load all possible drives, from
ad0s1a to ad9s1a, i get nothing. When i boot kernel.old, i see this:
atapci0: <Intel ICH7 SATA300 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfa00-0xfa0f mem 0xfdffe000-0xfdffe3ff
at device 31.2 on pci0
...
ad0: 152627MB <WDC WD1600AAJS-60PSA0 21.12M21> at ata0-master SATA150
It seems that FreeBSD recognises this drive as a SATA300 but later on refers
to it as SATA150. Could this be the problem.
This is what i have about this disk when i boot the RELEASE version of
FreeBSD:
#pciconf -lv
atapci0@pci0:0:31:2: class=0x01018a card=0x73361462 chip=0x27c08086
rev=0x01 hdr=0x00
vendor = 'Intel Corporation'
device = '82801GB/GR/GH (ICH7 Family) Serial ATA Storage Controller'
class = mass storage
subclass = ATA
#atacontrol cap ad0
Protocol Serial ATA II
device model WDC WD1600AAJS-60PSA0
serial number WD-WMAP96717073
firmware revision 21.12M21
cylinders 16383
heads 16
sectors/track 63
lba supported 268435455 sectors
lba48 supported 312581808 sectors
dma supported
overlap not supported
Feature Support Enable Value Vendor
write cache yes yes
read ahead yes yes
Native Command Queuing (NCQ) yes - 31/0x1F
Tagged Command Queuing (TCQ) no no 31/0x1F
SMART yes yes
microcode download yes yes
security yes no
power management yes yes
advanced power management no no 0/0x00
automatic acoustic management no no 0/0x00 0/0x00
# atacontrol mode ad0
current mode = SATA150
When i boot in verbose mode, i get this:
atapci0: <Intel ICH7 SATA300 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfa00-0xfa0f mem 0xfdffe000-0xfdffe3ff
at device 31.2 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xfa00
pci0: child atapci0 requested type 4 for rid 0x24, but the BAR says it is an
memio
ata0: <ATA channel 0> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ioapic0: routing intpin 14 (ISA IRQ 14) to vector 54
ata0: [MPSAFE]
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=03 ostat0=00 ostat1=00
ata1: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: stat1=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: reset tp2 stat0=00 stat1=00 devices=0xc<ATAPI_SLAVE,ATAPI_MASTER>
ioapic0: routing intpin 15 (ISA IRQ 15) to vector 55
ata1: [MPSAFE]
ata1: [ITHREAD]
...
...
ata0-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=40 wire
ad0: 152627MB <WDC WD1600AAJS-60PSA0 21.12M21> at ata0-master SATA150
ad0: 312581808 sectors [310101C/16H/63S] 16 sectors/interrupt 1 depth queue
GEOM: new disk ad0
ad0: Intel check1 failed
ad0: Adaptec check1 failed
ad0: LSI (v3) check1 failed
ad0: LSI (v2) check1 failed
ad0: FreeBSD check1 failed
ata1: reiniting channel ..
ata1: reset tp1 mask=03 ostat0=00 ostat1=00
ata1: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: stat1=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: reset tp2 stat0=00 stat1=00 devices=0xc<ATAPI_SLAVE,ATAPI_MASTER>
ata1: reinit done ..
ata1: reiniting channel ..
ata1: reset tp1 mask=03 ostat0=00 ostat1=00
ata1: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: stat1=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: reset tp2 stat0=00 stat1=00 devices=0xc<ATAPI_SLAVE,ATAPI_MASTER>
ata1: reinit done ..
ata1-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=40 wire
Any one with any ideas?
--
Mike
Of course, you might discount this possibility, but remember that one in
a million chances happen 99% of the time.
------------------------------------------------------------
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?7dc029620901290634q7ca5361ct496fc2c4a6bfe53f>