Date: Mon, 13 Mar 2006 15:51:07 +0100 From: Wilko Bulte <wb@freebie.xs4all.nl> To: Steve Rikli <sr@genyosha.net> Cc: freebsd-alpha@freebsd.org Subject: Re: DS10 6.0 new install hangs mounting root from ufs:/dev/ad0a Message-ID: <20060313145107.GA18799@freebie.xs4all.nl> In-Reply-To: <20060313143622.GA97709@dragon.genyosha.net> References: <20060313040335.GA90811@dragon.genyosha.net> <20060313073840.GA17327@freebie.xs4all.nl> <20060313143622.GA97709@dragon.genyosha.net>
index | next in thread | previous in thread | raw e-mail
On Mon, Mar 13, 2006 at 06:36:22AM -0800, Steve Rikli wrote.. > On Mon, Mar 13, 2006 at 08:38:40AM +0100, Wilko Bulte wrote: > > On Sun, Mar 12, 2006 at 08:03:35PM -0800, Steve Rikli wrote.. > > > Just finished an apparently uneventful install of 6.0 from CD > > > onto a DS10. > > > > > > The system hw is all healthy AFAI can tell -- it was previously > > > running OFS1 okay. > > > > > > The 6.0 install finshed and I rebooted -- last thing it ever > > > says on serial console is: > > > > > > ... > > > Waiting 5 seconds for SCSI devices to settle > > > Trying to mount root from ufs:/dev/ad0a > > > > > > and then nothing. No more <cr> or ^c or the like do anything. > > > > > > I've included as much of the serial console output as I could > > > capture. Suggestions/help/etc. very welcome. > > > > ATA support appears to be hosed on Alpha, and from looking at it this > > has been a problem for a long time. I run my DS10s with SCSI and > > did not notice any problems on those. It is also not only ATA on DS10 > > that has problems, my 164SX also suffers from it. > > Which SCSI controller & drive do you use? > > I suspected ATA was simply out in the weeds, so I installed an isp > and then later an ahc -- using a Hitachi 36GB (DK32DJ-36MW) caused > a panic during the device probing while booting the 6.0 install CD. I use an Qlogic isp1040, so the isp(4) driver > An 18GB Hitachi passed the probing, but the sysinstall never found > the drive to open for partitioning, even though the probing showed > it as da0. Sounds like the drive might have a pre-existing disklabel on it, this tends to confuse sysinstall on Alpha. > Both PCI scsi controllers yielded the same results; Alpha firmware > showed both drives, fwiw. > > I believe the drives are healthy, but I don't know of their contents; > do I perhaps need to zorch something in their volume header/label > ahead-of-time, just in case? > > cheers, > sr. > > > > > Waiting (max 60 seconds) for system process `vnlru' to stop...done > > > Waiting (max 60 seconds) for system process `bufdaemon' to stop...done > > > Waiting (max 60 seconds) for system process `syncer' to stop... > > > Syncing disks, vnodes remaining...3 0 0 0 done > > > All buffers synced. > > > Uptime: 38m17s > > > > > > halted CPU 0 > > > > > > halt code = 5 > > > HALT instruction executed > > > PC = fffffc0000757560 > > > Reseting I/O buses... > > > >>>show dev > > > dqa0.0.0.13.0 DQA0 Maxtor 5 3073H6 DAC10SC0 > > > dqb0.0.1.13.0 DQB0 Compaq CRD-8402B 1.03 > > > dva0.0.0.0.0 DVA0 > > > ewa0.0.0.9.0 EWA0 08-00-2B-87-3A-49 > > > ewb0.0.0.11.0 EWB0 08-00-2B-87-3A-29 > > > pka0.7.0.14.0 PKA0 SCSI Bus ID 7 5.57 > > > >>>boot dqa0 > > > (boot dqa0.0.0.13.0 -flags A) > > > block 0 of dqa0.0.0.13.0 is a valid boot block > > > reading 15 blocks from dqa0.0.0.13.0 > > > bootstrap code read in > > > base = 200000, image_start = 0, image_bytes = 1e00 > > > initializing HWRPB at 2000 > > > initializing page table at 3ff3e000 > > > initializing machine state > > > setting affinity to the primary CPU > > > jumping to bootstrap code > > > Loading /boot/loader > > > Consoles: SRM firmware console > > > VMS PAL rev: 0x1004700010154 > > > OSF PAL rev: 0x1003f0002014f > > > Switch to OSF PAL code succeeded. > > > > > > FreeBSD/alpha SRM disk boot, Revision 1.2 > > > (root@ds10.freebie.xs4all.nl, Wed Nov 2 16:27:20 UTC 2005) > > > Memory: 1048576 k > > > Loading /boot/defaults/loader.conf > > > /boot/kernel/kernel data=0x619410+0x39820 syms=[0x8+0x6c060+0x8+0x59b68] > > > > > > Hit [Enter] to boot immediately, or any other key for command prompt. > > > Booting [/boot/kernel/kernel]... > > > Entering /boot/kernel/kernel at 0xfffffc000034a9d0... > > > Copyright (c) 1992-2005 The FreeBSD Project. > > > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > > > The Regents of the University of California. All rights reserved. > > > FreeBSD 6.0-RELEASE #0: Thu Nov 3 01:10:43 UTC 2005 > > > root@ds10.freebie.xs4all.nl:/usr/obj/usr/src/sys/GENERIC > > > ST6600 > > > COMPAQ AlphaServer DS10 466 MHz, 462MHz > > > 8192 byte page size, 1 processor. > > > CPU: EV6 (21264) major=8 minor=4 extensions=0x303<BWX,FIX,MVI,PRECISE> > > > OSF PAL rev: 0x1003f0002014f > > > real memory = 1070841856 (1021 MB) > > > avail memory = 1040449536 (992 MB) > > > tsunami0: <21271 Core Logic chipset> > > > pcib0: <21271 PCI host bus adapter> on tsunami0 > > > pci0: <PCI bus> on pcib0 > > > isab0: <PCI-ISA bridge> at device 7.0 on pci0 > > > isa0: <ISA bus> on isab0 > > > dc0: <Intel 21143 10/100BaseTX> port 0x10100-0x1017f mem 0x1091000-0x10913ff irq 29 at device 9.0 on pci0 > > > miibus0: <MII bus> on dc0 > > > dcphy0: <Intel 21143 NWAY media interface> on miibus0 > > > dcphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > > > dc0: Ethernet address: 08:00:2b:87:3a:49 > > > dc0: interrupting at TSUNAMI irq 29 > > > dc1: <Intel 21143 10/100BaseTX> port 0x10180-0x101ff mem 0x1091400-0x10917ff irq 30 at device 11.0 on pci0 > > > miibus1: <MII bus> on dc1 > > > dcphy1: <Intel 21143 NWAY media interface> on miibus1 > > > dcphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > > > dc1: Ethernet address: 08:00:2b:87:3a:29 > > > dc1: interrupting at TSUNAMI irq 30 > > > atapci0: <AcerLabs M5229 UDMA33 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x10210-0x1021f irq 238 at device 13.0 on pci0 > > > ata0: <ATA channel 0> on atapci0 > > > ata0: interrupting at ISA irq 14 > > > ata1: <ATA channel 1> on atapci0 > > > ata1: interrupting at ISA irq 15 > > > isp0: <Qlogic ISP 1020/1040 PCI SCSI Adapter> port 0x10000-0x100ff mem 0x1090000-0x1090fff irq 35 at device 14.0 on pci0 > > > isp0: interrupting at TSUNAMI irq 35 > > > isp0: [GIANT-LOCKED] > > > atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 > > > atkbd0: <AT Keyboard> irq 1 on atkbdc0 > > > atkbd0: interrupting at ISA irq 1 > > > atkbd0: [GIANT-LOCKED] > > > fdc0: <Enhanced floppy controller> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 > > > fdc0: interrupting at ISA irq 6 > > > fdc0: [FAST] > > > fd0: <1440-KB 3.5" drive> on fdc0 drive 0 > > > mcclock0: <MC146818A real time clock> at port 0x70-0x71 on isa0 > > > ppc0: <Parallel port> at port 0x3bc-0x3c3 irq 7 on isa0 > > > ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode > > > ppc0: FIFO with 16/16/1 bytes threshold > > > ppbus0: <Parallel port bus> on ppc0 > > > lpt0: <Printer> on ppbus0 > > > lpt0: Polled port > > > ppi0: <Parallel I/O> on ppbus0 > > > ppc0: interrupting at ISA irq 7 > > > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > > > sio0: type 16550A, console > > > sio0: interrupting at ISA irq 4 > > > sio1 at port 0x2f8-0x2ff irq 3 flags 0x80 on isa0 > > > sio1: type 16550A > > > sio1: interrupting at ISA irq 3 > > > Timecounter "i8254" frequency 1193182 Hz quality 0 > > > Timecounter "alpha" frequency 462394124 Hz quality 800 > > > Timecounters tick every 0.976 msec > > > ad0: 28629MB <Maxtor 53073H6 DAC10SC0> at ata0-master UDMA33 > > > acd0: CDROM <Compaq CRD-8402B/1.03> at ata1-master PIO4 > > > Waiting 5 seconds for SCSI devices to settle > > > Trying to mount root from ufs:/dev/ad0a > > > > --- end of quoted text --- > _______________________________________________ > freebsd-alpha@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-alpha > To unsubscribe, send any mail to "freebsd-alpha-unsubscribe@freebsd.org" --- end of quoted text --- -- Wilko Bulte wilko@FreeBSD.orghome | help
Want to link to this message? Use this
URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20060313145107.GA18799>